Having problems with your Honda Karcher G2400HH-R Pressure Washer ?

Pump doesn't work [email protected]

\015 Pump doesn't work pump not engaging e-mail is [email protected] comcast.net pressure washer Karcher g2400 hb\015

Answers :

Repair Help & Product Troubleshooting for Honda Karcher G2400HH-R Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The spray from the pump doesnt hit the top rack and it doesnt clean the bottom rack effienctly. the pumps works and it does spray some but the sprayer in the middle doesnt extend all the way up


... Frigidaire 18 in. FDR252RB Built-in Dishwasher

My Bosch dishwasher (SGV57T03GB/08) is draining and filling with water but none is being let into the main pump. I can see water going into the side reservoir but it doesnt seem to be let into the main pump area - any ideas on what is not working? Dishwasher tray is dry and float switch is not stuck.


... Bosch 24 in. SGV57T03GB Built-In Dishwasher

Gsd5940 pump works but doesnt pump out the final rinse. it doesn't even try


... GE 24 in. GSD5940 Built-in Dishwasher

When I hit the start button on my dishwasher nothing happens. It still "finishes" the cycle but nothing ever cuts on. It doesnt fill with water and the sump pump never engages to drain the water that's not there. Any ideas? I know the inlet water pump works, I've detached it and connected it with a pigtail to an outlet.


Replace the main control board ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My dish washer fills with water washes but fails to empty so when door is opened plates are washed but water is left in the bottom the pump must be working as it doesnt leak is the controller faulty on that phasae of the cycle


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain ... Bosch Dishwashers

Whirlpool dwh b10.yesterday had problem with water not going anywhere,had to bail it out.today cleaned all filters,now can hear pump working but doesnt appear to be taking water in.i press start button for two seconds,re-programme,and it does the above.then start button flashes and there is a continual beep the programme indicator changes from a wash to rinse during this process.any help ? thanks pete.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have DW60BI dishwasher that has stopped working. Doesnt pump water, only makes the noise that indicates it has finished.


... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Dishwasher fills with water, but spray arms don't spray water or spin. As the cycle moves forward, water is eventaully pumped out (so the pump is working). i've selected different cycles with the knob on the front of the machine but they all work the same.... no swishing with the spray arms. When the cancel button is pushed, the water is pumped out... as it should. Thanks for the help.


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

Cancel wash working fine. when ready to wash get humming sound. pumpmotor not turning. A glass dish broke a week ago and work fine till know remove screen today found some small brokeb glass - like when a harden glass brakes? if something is in the pump how do i remove pump


In\015\012most dishwashers, the water pump is located under the lower sprayer\015\012arm. This component pumps the water through the dishwasher. The pump\015\012has two impellers, top and bottom. These, as well as other components,\015\012can become ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

I have a bosch shv99a13uc. i rescued this from a thrift store so i am not sure of the history . i have installed it . all the controls work . it fills and trys to work it dosen't spray much and grinds like a very loud timer what tests should i do and can i get a manual that shows me ho to get the pump out. I think it sounds like something in the pump any help would be great Thanks


Hello &\015\012Welcome to FixYa\015\012\015\012Please check\015\012this video on how to clean the pump filter:\015\012\015\012 ... Bosch 24 in. SHV99A13UC Dishwasher

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

GE Profile Dishwasher about 7 years old. everything seems to work door locks the machine trys to pump water in but it can't. I put water in thhe bottom of the machine and it does work a little but verry weak spray. It does pump out fine. Help


The washer doesn't pump water in--plumbing water pressure forces it in when the water inlet solenoid opens the valve. Check the water inlet solenoid--they are a common failure point. Look under the front of the washer behind the panel to find it--jus ... GE Dishwashers

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

Fuel pump not working when trigger pulled, all temp. lights on. checked flow switches all ok and new fuel pump coil an stalk fitted. the burner will work if the o ring removed from bottom of stalk allowing fuel through so something is stopping coil from getting 24v(it does get a nominal voltage of 10v)... anyone got any thoughts


... Pressure Washers

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Proline Logic diswasher won't pump out water. Checked the following:- No blockage Pump works OK Pressure switch appears to work OK What other faults could cause this problem.


... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

My ASKO 1805 Dishwasher started to smell weird and white smoke came from it. I turned it off, but after I turned it on again it just keeps pumping water in and out, I can't get in contact with it (None of the indicator lights are working and it is not reacting to any commands) In addition the safety feauture that is supposed to stop all operation the moment the door is opened is no longer working. (i.e. even with the door open it is still pumping water) Does it sound like an expensive repair? (


Hello,\015\012\015\012Welcome to FixYa. Based on your description ( specifically the white smoke and smell ) I would suspect the control board is faulty. \015\012\015\012If the unit does not stop when the door is open can be r ... Asko 24 in. 1805 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1110 seconds