Having problems with your Honda Landa PG 3500 PSI Pressure Washer ?

I have a power washer with a Honda 390 GX engine it runs and then dies

\015 I had it tuned: carberator cleaned, oil changed, spark plug changed thinking it needed a good tuneup. It does the same thing as when I brought it in- runs great for a few minutes, cuts out, then dies. What do I need to do?\015

Answers :

Repair Help & Product Troubleshooting for Honda Landa PG 3500 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a power washer with a Honda 390 GX engine it runs and then dies


... Honda Landa PG 3500 PSI Pressure Washer

13 hp honda pressure washer 3000 psi 4gal/min Hard to start and dies out after 20 seconds after the engine gets hot and running after multiple starts the engine will stay running but then dies every 30 minutes


There are a couple of things that can cause this problem. The first thing to check is if you are loosing spark. Dying after it gets hot sounds like to stater is failing in the engine. If you loose spark this is more than likely the issue. If you are ... Honda Landa PG 3500 PSI Pressure Washer

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

I have a Honda ,gas powered power washer and when I squeeze the handle the water pump kills the motor. I've let the engine run until warm and it still can't take the water pump engaging. It's a three year old washer.


... Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

I have a keihin carb on a honda engine, used on a power washer, that only runs with choke fully engaged. I have taken the carb apart and cleaned it thoroughly to no avail. the part # on the carb can't be found online. I don't know enough about carbs, theory of operation, to continue and can't find a technical ref for the keiwin being used, any suggestions as the only # on the carb yeilds no hit on the web. # stamped on carb is 65bbkf7


... Honda Pressure Washers

Why wont blackmax power washer 2700 psi honda engine wont stay running once i spray


... Honda Pressure Washers

Honda Pressure Washer Black Max 2600 Psi 161cc Problem: manual choke pulled on when starting. When attempting to turn off the choke the motor dies. This occurs no matter how long the engine runs for.


... Honda Black Max 2600 PSI Pressure Washer

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

Honda GC 160 Engine, I had the carb replaced about 1 year ago, now its doing the same thing. At first it wouldnt start at all, I cleaned the carb, then it started would speed up and die. I then took the carb off and cleaned the jets, now it starts with the choke in the closed position only, at high speed it sputters and dies, but will I run it at med speed it runs but will die with tiller has a load, also when you put the choke to open it always dies. I dumped all the gas, and checked the fuel


This really sounds like a carb problem, good to hear that you are taking the carb all the way off and soaking it, this is the best way to clean a carb. I don't think it would be the fuel pump, they either work or they don't. I would check the governe ... Karcher 2500 PSI Pressure Washer

I have a XR2600 honda pressure washer that the engine dies when you stop spraying


... Pressure Washers

I have a XR2600 honda pressure washer that the engine dies when you stop spraying


... Pressure Washers

I have a XR2600 honda pressure washer that the engine dies when you stop spraying


... Pressure Washers

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

DeVilbiss Pressure WAsher EXH2425 Honda engine GC160qha pump DAPC axcial cam. When using washer sprayer both the engine and pump seem to operate normally. As soon as I let off the trigger of sprayer the engine dies. Help?


Hi and welcome to FixYa. I am Kelly \015\012Take a look at your engine parts manual here: \015\012\015\012 ... Pressure Washers

John Deere power washer with the Honda GX390 on it that won't stay running.


... Master Heaters Pressure Washers

My Honda gx160 5.5 hp engine only runs with full choke on. This has been the case since it was new. The engine runs very smooth, but dies if I open the choke. Thanks


... Karcher 2500 PSI Pressure Washer

The washer will run about 2 min. then die. i have checked the oil, air filter and gas. it has good presure when running then it acts like its out of gas by stalling and dieing. Problems with Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt?


It is possible that the oil pressure switch is not functioning properly or you have a lighter oil in the machine than is recommended.Post a comment if you need more assistance. ... Honda Pressure Washers

For pressure washer Model WP-2402-SWHB, SN 10132043: With Honda engine running, or no engine running, no water will pass through the pump.


Hi If no water is passing through your pump on mains water pressure and not sucking from a barrel then it will be either a blocked nozzle,blocked unloader on the side of the pump or a blocked water filter. ... Pressure Washers

I have a B&S 3.75, model 98902,type 014301,code 96032254 gas engine which powers a 1500PSI Clean Master power washer. The engine will start if primed but will not continue to run unless fuel is sprayed down the throat of the carburator.Apparently a gumedup/dirty carb. what is the best way to proceed to clean it? Where is best place to get a rebuild kit and/or replacement carb if needed? What are other possibilities if not a dirty carb?


... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a Honda Excel Pressure washer with 5 hp engine. I just started using it for 5 - 10 minutes and the engine stopped running. I can't pull the cord to turn over the engine. Ithas plenty of oil, I disconnected the hose and the wand and still can't get the engine to turn over.What next?????


... Pressure Washers

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

Rebuilt honda GC160 5hp engine for a power washer and only got the engine to start once. Just took apart and saw that the cylinder and piston was all scored up again.


... Honda Pressure Washers

Honda gas power pressure washer runs for awhile then cuts off.


Did you pour all of the old gas out before you started to use it. Sometimes condensation builds up in gas tank when stored. You need to dump old gas an put in new gas. ... Honda Karcher G4000RH Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0925 seconds