Having problems with your Honda Maxus Pressure Washer MX5222 ?

Pull cord is loose on my Honda 2500 Pressure Washer unable to start engine.


Answers :

Complete pull rope units are available for appx $23
Repair Help & Product Troubleshooting for Honda Maxus Pressure Washer MX5222

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pull cord is loose on my Honda 2500 Pressure Washer unable to start engine.


Complete pull rope units are available for appx $23 ... Honda Maxus Pressure Washer MX5222

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Start problems The 1st time I tried to start my Honda 2400 pressure washer the pull cord came all the way out with no resistance and it wouldn't recoil. I took it to a repair shop and they said atyhe engine was shot due to a broken piston. How could this have happened and is a new engine the only fix?


... Honda Pressure Washers

I have a Honda Excel Pressure washer with 5 hp engine. I just started using it for 5 - 10 minutes and the engine stopped running. I can't pull the cord to turn over the engine. Ithas plenty of oil, I disconnected the hose and the wand and still can't get the engine to turn over.What next?????


... Pressure Washers

I have Honda pressure washer.Inorder to start the pressure washer you have to pull the cord. THe cord is stuck and I am not able to pull the cord. Why it and what should I do to start the washer.


... Honda 2500 PSI Gas Pressure Washer

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

Karcher G 3050 OH pressure washer with honda engine: The pull cord is locked so I can't start the machine. Help!


The model G3050 OH use gas or mix? ... Pressure Washers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

Honda XR 2600 pressure washer, cord will not pull on engine


This is typically due to the unloader bypass valve not operating properly. You can remove and clean this valve or you may want to replace the valve with a new one.If you take the high pressure hose off of the pump and with the water turned on you ... Honda Maxus Pressure Washer MX5222

I tried to start the pressure washer by lulling the cord, there was sharp popping noise, and the engine would not crank to start. It is a Honda K. washer. What went wrong? Pls advise, thanks.


Make sure your oil level is correct and not overfull. If ok, pull the sparkplug out. Then, pull the starter rope to see if the engine spins freely. If it does, pull it 4-5 more times to clear the cylinder of oil or gas. Put the plug back in and try i ... Honda Pressure Washers

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

My Honda GC160 engine on my pressure washer is next to impossible to pull start. I have checked and added oil to make sure it is full. Still no luck getting it to pull.


Honda pressure washer ohv was running great died like someone turned of the switch ! has spark, oil full, sparkplug looks good any ideas please. ... Karcher 2500 PSI Pressure Washer

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers

Honda gcv160 pressure washer won't turn over. pull cord just starts to move then STOPS hard.


... Honda Pressure Washer PSI 3000

Cannot pull start pressure washer. Cord will not


Cord will not extend past 3 inches; just shut down after last use after 30 seconds. ... Pressure Washers

Hello, I own a Honda Pressure Washer (Porter Cable Model) with a Cat pump 2600psi and 6.5 hp. An Excellent machine for the past 7 years. Last fall I noticed it was not producing the full pressure but still Engine was running strong. This past weekend. started it up and used it for about 1 hour still with minimal pressure at full throttle. Then pressure was totally cut off. I stopped and started the engine the engine and it had minimal pressure again. Same thing happened again. I stopped the engi


... Honda Pressure Washers

HAVE A DEWALT PRESSURE WASHER WITH 6.5 HONDA ENGINE THAT WAS STORED FOR A COUPLE OF YEARS. IT WILL START BUT ONLY RUN FOR3-4 SECONDS WITH CHOKE ON THEN KILLS. WAIT A MINUTE OR SO, PULL ROPE AND WILL RUN FOR ANOTHER 3-4 SECONDS. WON'T RUN CONTINUOUSLY. PUT FRESH GAS AND CLEANED BOWL UNDER CARB. ANY OTHER TIPS? THANKS, FOREST


Look for plugged filter anywhere in fuel line. ... Pressure Washers

My porter cable 2400 psi pressure washer will not start. has honda engine gc160. pulled plug and put up against frame and it has spark. It's full of oil.


... Porter Cable Cable Commercial Pressure Washer PCH3200

I have honda gcv160 5.5 pressure washer, after sitting over winter, I went to use it, and I can't even pull the cord to try and start it. What are any reccomendations as to what I can do to fix this?


My power washer started doing that after the pull-cord mechanism broke.I took off the hoses to make sure there was no back-pressure caused by the pump.And pull rope was still frozen.We took off the pull rope cover on top of the mach ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1609 seconds