Having problems with your Honda Maxus Pressure Washer MX5222 ?

Retentioning a pull cord

\015 How do i retention a pull cord? do i pull the assembly off?\015

Answers :

Yes
Repair Help & Product Troubleshooting for Honda Maxus Pressure Washer MX5222

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Retentioning a pull cord


Yes ... Honda Maxus Pressure Washer MX5222

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

My neighbor just gave me a Troy Bilt 020207 power washer. It is 2450 PSI and 2 GPM. He snapped the pull cord rope. I looked at the pull cord cover and it seems to have 3 rivets holding it to the main housing. How do you recommend to repair or replace the pull cord?


Sounds like a briggs engine, DONT remove the rivits, go down a little further and remove the 4 3/8 bolts that hold the blower housing on.Turn it upside down, prewinf the pulley in the direction that it turns when the rope is being pulled. When it sto ... Briggs & Stratton Pressure Washers

I have Honda pressure washer.Inorder to start the pressure washer you have to pull the cord. THe cord is stuck and I am not able to pull the cord. Why it and what should I do to start the washer.


... Honda 2500 PSI Gas Pressure Washer

I have an Excell VR2522 that will not start after sitting for a while. Tried pulling the cord and it would pull okay for a while, then it tightened up to the point that I could barely pull the cord. Any help?


... Karcher 2500 PSI Pressure Washer

Just bought a john deere 3300 power washer. It started with no problem. shut it off to answer the phone. When I went to start it the pull cord wouln't pull tryed everything but still the pull cord was in a locked position. Don't know what to do hoping you have an answer for me


First turn off the water to the machine. pull the trigger to release any trapped pressure in the high pressure hose, then try to start the machine. if it starts then turn on the water to the machine.it may be that the engine is tryi ... Pressure Washers

I purchased a Honda Power Washer Model PWH2600 two weeks ago. I cleaned half my deck when the motor shut off unexpectantly, and now the cord will not pull to restart the engine. Any ideas what I can do for the cord to pull normally?


You just bought it so it is under warranty. I would take it back to the place you bought it for service. If the starter rope will not pull then the engine may be locked up. Check the oil level and make sure it is full before returning it for service. ... Honda Pressure Washers

Pull cord won't pull out


... Honda Maxus Pressure Washer MX5222

Pull cord is stuck and will not pull


TAKE THE PLUG OUT AND THEN TRY ... Honda Maxus Pressure Washer MX5222

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

The rip cord wont pull to start pulls once and then wont pull real hard to pull


Try squeezing the wand when you are starting the motor.\012it will let the water pressure go through. ... Honda Pressure Washer PSI 3000

I havehonda gs 160 5.0 hp petrol powerwasher,it madea noise and just stoppe going,the pull cord wont even pull what is wrong?


Did you figure this out ... Pressure Washers

PULL CORD TO HARD TO PULL FOR A POWER WASHER


... Psi Blue Max 2200 High Pressure Gas Power Washer

Just bought a jet usa 7.0HP 3950 PSI pressure washer, put it together and put oil in it and i cant pull the pull start cord out at all?


... Pressure Washers

Pull cord won't pull


I'ts a possibility that the engine has seized, remove the spark plug and look at it it will give you and indication if the engine is burned up. ... Honda Maxus Pressure Washer MX5222

Pull start won't pull. Engine was running then stopped. Now the pull cord won't extend


First. Turn off the water....Release all of the pressure off of the hose and pressure washer. Try and pull again. If it still won't pull check to see if there is oil in the engine. The engine may have locked up. ... Briggs & Stratton 2200 PSI Gas Pressure Washer

Cannot pull start pressure washer. Cord will not


Cord will not extend past 3 inches; just shut down after last use after 30 seconds. ... Pressure Washers

Excell vr2522 pull cord jammed


Is the garden hose connected and turned on?If so make sure that the trigger on the gun is being pulled while your trying to start the engine! The backed up pressure in the high pressure hose can mimic a blown or seized engine in this situation. ... Pressure Washers

Pull cord getting stuck


Pull cord is completely hard to pull. Pressure washer stopped running and the pull cord is locked. ... Karcher 2500 PSI Pressure Washer

Pull cord is locked. Was running fine and just


Any oil in the engine? pull cords are easy to replace but sounds like you run out of oil and the engine locked up! ... Karcher 2500 PSI Pressure Washer

My pull cord to my pressure washer is hard to pull and it's not starting. Why? This all started after I tried to start it without the water on while attempting to start.


Take out the spark plug and trying pulling it , if its still tight then you may have seized your pump ) , put a rag over te spark plug hole as there may be fuel/oil mix in the cylinder , check the oil in the engine , check the oil in the pump ( look ... Pressure Washers

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

Pull cord seems to grab and can't get it to start since it grabs too quickly..... tried pulling it out slowly and then let it feed back... no good... manual doesn't address this at all


... Karcher G 2600 VH Gas Pressure Washer

Pull cord on gcv160 stuck, hear a grinding when I try to pull it


... Craftsman Pressure Washer 2600 PSI, 2.3 GPM Honda Powered CA
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0266 seconds