Having problems with your Honda Pressure Washer PSI 3000 ?

Torque on rocker nuts

\015 Have a honda 5.5 160. had a push rod bent. somehow, the valve was not bent. replaced head gasket, cleaned and checked valves, replaced valve guide seals. got it all back together, set the valves at tdc. question is how do you set the 17 ft lb torque on the rocker nut. every time I begin to torque it, the nut just keeps turning in until the valve is pressed all the way open. hope this makes sense. dont know any other way to explain it. thanks, jay\015

Answers :

First of all, put down that torque wrench! It's BS that the mfr puts in there to cover their ***.

You'll need a 14mm and 10mm open end and of course a set of feeler gauges.

With the small nut loose set your gap ( .006 intake/ .008 exhaust +/- .001 on each). Once you got your gap, hold the large nut with the 14mm and tighten down the small one. Now check your gap again, it hard to keep from moving slightly and my take a few attempts. You want to make it snug but don't gorilla torque it.
Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Torque on rocker nuts


First of all, put down that torque wrench! It's BS that the mfr puts in there to cover their ***.You'll need a 14mm and 10mm open end and of course a set of feeler gauges.With the small nut loose set your gap ( .006 intake/ . ... Honda Pressure Washer PSI 3000

Noticed water on floor. Found both heater nuts cracked and letting water by the rubber gasket and tub. Water leaking into the heater power supply wires. Bought new nuts and want to know if this is a constant issue. Nuts are just cheap stampings and it seems likely it will happen again. Any suggestions Don


Change out your heating element as well. Sounds like you need a better seal. \012\012Thanks ... Dishwashers

My dishwasher did not clean well. I replaced the seal on the bottom spray arm. there is a wobble now. the nut does not seem to screw down tightly. there is nothing wrong with the nut, it simply does not reach. I don't know if the lower arm is supposed to wobble, or if the nut should screw down tight. I can't seem to find a picture anywhere so I can visualize exactly how the spray are fits together. Is there a diagram on line? Dishwasher model: whisper quiet #KUDM25SHW1 bought in 1999


... KitchenAid Dishwashers

Removed lower spray arm of KitchenAid dishwasher and need to reinstall it. This installs over a spray arm nut that is a split ring. The nut goes over the outlet pump. I cannot get the nut to go over the outlet pump and then go inside the spray arm, which is 1/4-inch smaller in diameter.


... KitchenAid KUDS24SE Built-in Dishwasher

Fisher Paykel dish wash 920. Plastic door latch on main body is broken and is held by bolts with nuts in the lining. How to replace latch and bolts when nuts have moved out of place?


... Fisher and Paykel Dishwashers

I have Whilpool dishwasher, model# GU 980SCGB3. The nut (part# 8268873) is broken and screw side is stuck inside. How to take it out to replace the nut.


Go to a hardware store and get a tapping system for screws and tap the screw to remove broken screw ... Whirlpool Dishwasher Lower Sprayarm Nut 8268873

What size are the two nuts that hold down the plastic cover that covers the sprocket wheel. Seems to be 5/16-24 but my thread gauge fits the threads at about 20 threads per inch????????????? Is these metric screws and nuts.


... Champion 26 in. D-HBC Free-Standing Dishwasher

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

The note by FixAllPhil entitled "Poor cleaning or noisy pump on Whirlpool or Kenmore dishwasher" has a significant error. The first step should be to "Remove the lower wash arm (1) by turning the nut CLOCKWISE (right)". I damaged the threads on my dishwasher nut by trying to turn it counterclockwise. Once that error is corrected, please remove this post.


Thank you! ... Whirlpool Dishwashers

The brass nut on the bottom of the heating element has a split in it and will not tighten up. One on the common wire is leaking and i can not get this nut tight enough to stop the leaking. Any suggestions?


The only thing to do is replace the nut the part number for the heater nut is 154106202. they run about 3.50 dollars from a local parts supplier ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

I need bolt torques and valve clearences for pressure washer?


... Pressure Washers

Threads stripped on nut holding lower wash arm


... Whirlpool Dishwashers

Trying to replace the brass nuts to the heater element to dishwas


... Frigidaire Dishwashers

A grey oil coming from a yellow brether nut on


That breather is the oil port that lubes the engine. As it heats the oil expands....you over filled it ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Torque tornillo cabezote gx390


... Honda Pressure Washer PSI 3000

Hub nut and strainer basket


Call a service tech! ... Dishwashers

MY GU 2400 DISHWASHER IS CLOGED WITH SHAVED PECAN NUTS


... Whirlpool GU2400XTP Built-in Dishwasher

Where can purchase pressure fit axle nuts for my


These are available at Lowe's/similar. \015\012Best regards, --W/D-- ... Karcher 2500 PSI Pressure Washer

Need to know the head bolt torque for Craftsmam Pressure Washer


... Pressure Washers

Karcher 720 mx white seal nut underneath leaking


... Pressure Washers

I need a switch fo a Mcculloch FH140A or rocker parts


The switch number I found is 7022140A02 and list is 2.84. You can go to McCullochpower.com and find a dealer near you or order the part online. You can follo the links to look at the same breakdown I found for other parts ... McCulloch FH160G Pressure Washer

Torque foe head bolt on Craftsman High Pressure Washer 7.0 Horsepower 2900 PSI 2.3 GPM Model Number 580.752410


... Pressure Washers

Won't drain The water won't drain away, I have the top off and the spinner spins easily, but I can't seem to remove it. I have the screw driver trying to turn it while holding the 1" nut, I don't know if this is the way to get to the bottom of the pump. Its a kenmore fh3726568. built in.


Hi,\015\012Please follow the steps provided bellow :\015\012Fill washer with water and wait for the timer to get to the drain mode. \015\012Unplug the washer from the electric outlet. \015\012Open the case, and disconnect the ... Kenmore 24 in. 15689 Built-in Dishwasher

Grinding Noise I think someone dropped some pistachio nut shells in the dishwasher. How do I clean them out. It's making a terrible grinding noise.


Wash out the drain and filter. ... Amana 24 in. ADB3500AW Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0156 seconds