Having problems with your Honda Pressure Washer PSI 3000 ?

Honda gx340 hi i have a honda gx340 the valves have bend on me twice how is this happening and can i stop it from bending them


Answers :

Have the engine timing set correctly so that the valve do not contact the piston.
Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Honda gx340 hi i have a honda gx340 the valves have bend on me twice how is this happening and can i stop it from bending them


Have the engine timing set correctly so that the valve do not contact the piston. ... Honda Pressure Washer PSI 3000

Honda gx340 the valve have bent on me twice could u tell me what is the cause of this.


Hi,Typically Honda GX engines are pretty much bullet proof, but the GX340\015\012and 390's need valve adjustments more regular then the smaller Honda's.The bent one might be there due to many reasons - worn out, Improper setti ... Honda Maxus Prosumer MX5223 Pressure Washer

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

My husky gcv 160 with a honda motor, has stopped pumping water. My brother said he went to use it and the motor wouldn't pull so he left it alone, i tried it and it pulled and started fine but the pumps not pumping and the relief valve( guess that's what it is) is spraying intermitingly, Could you please help, Thanks


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Hi i have a honda gx340 11hp washer it has.nt being used in over 2 years i had to change the valves, got it going now its blowing black smoke and running very low on power thanks shane.


Hi,It would generate smoke if there is too much oil is left in the filter. Check air cleaner and it would fix the issue.Let me provide you with Service Manual ( Generic ) for all the Honda Engines.The link would be ... Karcher 2500 PSI Pressure Washer

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

Inlet Valve keeps stopping and starting, takes a bit of water then stops take a bit more then stops, on off on off for about 10 mins until its taken enough water to srta the cycle , have replaced the Inlet Valve still happening and water flow meter with pcb still happening Any suggestions? It a DWLT65


What about the overflow valve? It could be sticking ... Beko Dishwashers

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

Solenoid Vater Valve or Aqua Stop Valve


On your model the aqua stop valve is the root of what is causing the leak, the check valve inside the aqua stop is reducing the pressure too far and the seat on the water inlet is bypassing due to the aqua stop.So to repair this order the ... Bosch Dishwashers

I have a SMEG DWF614 SS dishwasher. I continue to get an E8 error message. The diverter valve motor turns freely & the motor turns freely when they are seperated. However, when they are assembled, the motor turns the valve & continues to try turning the valve when the valve is on its stop position. Is the motor & valve faulty or is it the control. If you can answer, what part number would I require. Regards Leighton Davies


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Honda gc160 steps to change a broken valve


... Pressure Washers

GE model#vrb4119vw129 My water inlet valve wont stop pumping water after the tub is full. I have replace the water inlet valve and the float switch.


... Dishwashers

My friend gave a pressure washer honda 5.5. He tried to adjust the valves now it won,t start. What is the valve clearance


The valve clearance is 0.15mm Intake 0.20 Exhaust ... Honda Pressure Washers

When hood is lifted up water do not stop running, Have to close the shut of valve to stop water.


Hello,\015\012There is a magnetic switch underneath and behind the panel I think its at the front or side where the lid sits.this may be faulty but sometimes they can drop out of line,look up inside hood for other half of sensor this may have c ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

I have Whirlpool dishwasher about 3years old it is the ADP7966 AAA 6th sense. When I put it on and turn the temperature knob, only the first temperature green light comes on althou I can turn the knob all the way round none of the other lights come on, my rinse aid and salt programmes light up thou ,and when I press the start button it flashes twice stops a bit then flashes twice again, and thats all it keeps doing. I would be very grateful if you help to solve the problem. Many thanks to you.


... Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Have a Power washer with Honda 390X engine. Engine intermittently stops and has to be manually restarted. It only stopped once in 10 hours yesterday, but already several times today.


... Honda Pressure Washers

Honda GVC 160 lost pressure - noticed small black valve (back - rear) after pressure builds up , short spray then nothing - hot water comes shooting out the black valve - did something pop off?


The small black valve is called a thermal relief valve. If it is open you will have no pressure. If the water is getting hot enough to pop that valve, there might be internal problems with the pump. ... Karcher 2500 PSI Pressure Washer

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

Asko Dishwasher DW20.1 d3120 Water not coming through inlet valve. I have replaced the inlet valve - solenoid only releases when on/off switch and start button are pressed and released simultaneously. A burst of water comes out at that point and stops. What could be wrong?


Hi, Welcome to FixYa.\015\012\015\012I'll start by saying your description sounds exactly like a symptom of a faulty control board on Asko dishwasher's...specifically the relay responsible for energizing the fill valve. It sounds to me like the relay ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0595 seconds