Having problems with your Honda Pressure Washer PSI 3000 ?

I have a Honda 3500 pressure washer. The motor

\015 I have a Honda 3500 pressure washer. The motor starts fine. When I pull the trigger, water comes out under pressure, but the engin stalls. I think it's the oil pressure. Any ideas?\015

Answers :

You need to start the unit and let it run for few minutes to get worm, make sure the water is fully open and the unit is fully cleaned. Push on the trigger on and off for few times not letting the unit shutdown, then start increasing the fuel mixture ¼ turn and push on the trigger again and see…this could be that the unit need service or the governor springs getting week if you got one on your unit…let me know how that work for you and please do not forget to rate my service so we can improve on it with your help. God bless
If the oil level is OK and no leaks it should be OK there
It may be the idle is too low or it may just be a blockage in the nozzle
Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Honda pressure washer model # exhp3640-1 3600psi 0=13hp has low water pressure out of triggers motor does not engage for higher pressure


... Pressure Washers

Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure


What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

11 hp honda motor on landa cold water pressure washer runs good except when trying to pressure wash the motor & pressure go up & down pulsating bbruummmmmbbbbrrruummmmbbbrruuummmmwhats the problem and how to fix it?


... Honda Landa PG 3500 PSI Pressure Washer

I change oil on my 3700 psi honda motor pressure washer motor and pump and after i done that the tigger rope is to hard to pull looks like some who is pressure some where can some one help me whit this problem .. thank you


Most likely has nothing to do with oil change. Have someone hold the trigger on handle open to relieve pressure on system/pump , this will make engine turn easier when you pull rope. ... Karcher 2500 PSI Pressure Washer

Honda 2400 psi before it went out i cold tap the end of the wand on the ground and the pressure would return now when pull the trigger there is no pressure only a fine spray .its a karcher with a honda motor thanx


Hi, there is a small ball bearing inside the nozzle on the end of the lance , this can get jammed or missaligned and the nozzle orifice can get blocked , clean this or replace the whole lance with another 200 Bar lance .hope this he ... Honda Karcher G2400HH-R Pressure Washer

I have a 3000 PSI Honda pressure washer. The motor


Your nozzle could be plugged or partially plugged. Also, try running it with the high pressure hose taken off to flush the pump. ... Honda Pressure Washer PSI 3000

I have a Honda 3500 pressure washer. The motor


You need to start the unit and let it run for few minutes to get worm, make sure the water is fully open and the unit is fully cleaned. Push on the trigger on and off for few times not letting the unit shutdown, then start increasing th ... Honda Pressure Washer PSI 3000

I have a Husky gasoline pressure washer. The honda motor starts but stalls because the pressure by-pass (not the right term) doesn't seem to open and builds up pressure. I haven't tried to remove any parts yet. I think grit has got in but don't know for sure. The pump looks pretty simple and the part I want to remove for cleaning looks like a plastic hexagon nob. Will this access the by-pass or is it something else.


I think you're right about the knob, but try this:Open the water to the washer. Leave the line open, and hold the trigger down to get all of the air out of the supply and discharge lines. While still holding the trigger down on the spray gun, ... Pressure Washers

I have a DeVilbiss pressure washer, Serial# 2251136878, Model# WVRH2421, Radial Pump# D28703, with a 5.5hp honda motor. It has no pressure. If the pump can't be fixed, is there another brand of pump that will fit this model pressure washer?


THE PUMP FITS THE MOTOR and the pump i always use is a ROYALPUMP made in Italy and they are long lasting and easily serviced ,any of the Italian pumps are good ... Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

No pressure to the wand. Motor runs and pressure gauge reads 4000 psi.Feels like no power in the wand Is a Honda pressure washer model #BEEX-2965HWCOMX.


... Honda Pressure Washers

NO PRessure i have a Honda gcv160 5.5 dt2400cs CRANKS RUNS FINE AS LONG AS TRIGGER IS pulled to let water trough it has no pressure soon as you let go pressure starts building then it kills the motor will not run unless you hold handel


Hi It sounds to me like your unloader valve is stuck, this is the thing that is meant to move up and down when pressing the trigger.Please remove the unloader valve assembly and check for damage. If no damage is found then grease and lubricate this p ... Honda Pressure Washer PSI 3000

GX 340 Honda motor has no visible spark. - Honda Maxus Prosumer MX5223 Pressure Washer


... Honda Maxus Prosumer MX5223 Pressure Washer

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

Cvg 190 honda motor flywheel frozen - Honda Pressure Washers


... Honda Pressure Washers

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

I have a Husky 2600 Psi 2.3 GPM Honda powered gas pressure washer. When i turn it on the motor runs fine, But when i squeeze the trigger the water is not pressurized when it comes out. How do i fix this problem?


... Honda Pressure Washers

5.0 Hp Honda motor for pressure washer . Will not start. pops threw carb. seems to have back pressure, without waterpump attatched.


... Simpson PS2600 PowerShot Commercial-Duty Gas Powered Pressure Washer

Absolutely no water pressure on Husky 2600 psi w/ HOnda motor


Hook up water hose dose not pump water? ... Pressure Washers

Troy built pressure washer won't start. It has a Honda 160 CVG motor. I used it for about a year and then it stopped working. I've replaced fuel and spark plug. Spark plug is soaked every


... Karcher 2500 PSI Pressure Washer

Water connected to new tt2028 pump on honda motor and nothing happens, no leaks but no pressure


... Northstar Pressure Washers

Where can i find pricing an parts for a pressure washer model 01903? honda 5.0 horse motor,2450psi/2.5gpm??


... Karcher 2500 PSI Pressure Washer

Wont start I have a North Star pressure washer that has been in storage for three years.It has the Honda motor GX 160 5.5 I put in new gas changed the oil, air filter,and spark plug.But it wont kick over. Im not sure how to work the levers upon starting it.Theres one for gas, choke,idle,and of course an on switch.Please help


Tip a cap full of fuel in top of the carb to start intitially, check for spark as common fault is on/off switch, If no spark, link the 2 wires on on/off switch together. ... Pressure Washers

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0484 seconds