Having problems with your Honda Pressure Washer PSI 3000 ?

My motor will not start?? It gets spark, I see the piston fire, Is it out of time. seems like there is too much gas. How would I check for timing. Or other problem. Mike [email protected] thanks for the help.


Answers :

Has it been sitting for a long time? 9 times out of 10 the carburetor is dirty and just needs to be cleaned. you could soak it in some carb cleaner sold by auto parts stores or go so far as to buy a rebuild kit for it and replace gaskets and such.
Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My motor will not start?? It gets spark, I see the piston fire, Is it out of time. seems like there is too much gas. How would I check for timing. Or other problem. Mike [email protected] thanks for the help.


Has it been sitting for a long time? 9 times out of 10 the carburetor is dirty and just needs to be cleaned. you could soak it in some carb cleaner sold by auto parts stores or go so far as to buy a rebuild kit for it and replace gaskets and such. ... Honda Pressure Washer PSI 3000

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

The whirlpool agp 931 keeps blinking 7 times, puase, 7 times when I start it. It does not do the washing program . Is that a code for an error? any help would be much appreciated


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or it can be a simple glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Whirlpool 18 in. ADP530 Free-standing Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

Hello, My GE dishwasher stopped draining. Model Number: VSD2304JOOWW I emptied out the dishwasher of the liquid, removed the cover and checked the filter. (Didn't look bad.) Checked the drain pipe under the sink and there was a little debris (slime) but very minimal. The garbage disposal was installed at the same time as the dishwasher 3 years ago (brand new place). What else could it be? Any advice would be helpful as my new home seems to be falling apart and it is getting pretty e


Drain pump either disconnected or jambed ... GE Profile PDW8400J Built-in Dishwasher

Hi, I have a bosch SGS43E02Z dishwasher that dont seem to wash clean. It would seem that some times the presure from the spinning washers arnt working well enough as it dont even move rice from plates stacked next to each other. i have checked all filters inside the machine and if you start a wash program the sprayers work and the water is splasing. please help with sugestions.


... Bosch Dishwashers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

I have ge nautilus...it has been working great but last time i turned it on it worked for app 3 mins then just got quiet. its not making any noise. wondering if anybody has suggestions as to what might be problem. i checked the breaker..it wasn't tripped. any ideas would be helpful. thanks


Sometimes the door switches go bad. If you are handy you can break it apart and clean the contacts. ... GE Nautilus 24" Built-in Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

I had gas problems cleaned the carb,brass tube,filter many times. engine would start run for 20 to 40 sec.start to hunt than stop oil is new at correct level even unplugged the level device, the same results. ordered a new carb. installed it same results taken cap off tank to check if it is not a vent problem.I have tried everything, HELP


Try to start it and then start spraying with it to make sure that your pressure relief valve is working. My son-in-law had this problem and it was because the pump built up so much pressure that the engine couldn't overcome it and it would stall out ... Honda Pressure Washers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

I have used the McCulloch (FH180A) three times over the course of two years. On my fourth use the pressure washer just surged on and off and I would get a tiny spray from the gun each time it surged. In other words it would do nothing. Please help... very frustrated. Thanks


Sounds like the problem could be low input water flow or pressure. There could be crud on the intake where you hook up the garden hose, there could be some other sort of blockage. Try hooking it up to the hose and pull the trigger (with the po ... McCulloch FH180A Electric Pressure Washer

Hi There I am having a problem with my Candynova CD122J Dishwasher, The problem is the water is not emptying out of it, I have checked and cleaned the filter and made sure there was not cutlery etc caught in it, Have you come across this problem before or would you have any help on this?? Any help would be well appriciated. Regards, John 00353852113372


Water pump could be out could be restriction in the hose that runs into the sink drain ... Dishwashers

We have standing water in our GE monogram dishwasher at the end of the cycle. I checked the hose and there is no blockage. Would a reset help this? Do I need to contact a technician? Any help would be appreciated. Thanks!


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Dont think reset will help as dishwasher not draining properly\015\012or not draining at all issue ... GE Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Lately the soap remains in the dispenser, dried and caked in (I have to dig it out with a sharp object, as it becomes a solid piece). I have also tried gel soaps, but find them in the bottom of the dishwasher, partially intact. The mistery is this does not happen all the time, but most of the time! I've checked the water pressure and the water temperature: both seem to be fine. The dishwasher does run a full cycle. Is it time to buy a new one? Would you also be able to tell me what year this mod


... Frigidaire 24 in. GLD3450RD Built-in Dishwasher

I have a hotpoint aquarius DF22, problem: machine not taking in water to commence the cycle, (this is intermittent and worked sometimes) the plumbing has been checked regularly and for a time would start after reconnection, the motor is fine the electrics have been checked by a qualified electrican who cannont source the problem, now the machine will not take in water at all, any suggestions please?


... Dishwashers

3 wk old Kenmore Elite D/W will not drain. Have attempted to Cancel/drain several times. Tried short cycles. Checked twist out filter. Baffled. Help? Is there a way to manually drain? Manual no help.


Hi,Sorry you are having trouble, this is a good dishwasher I have the same one in my home.In order to help I need to ask you a couple questions.When you push cancel drain if you listen close, do you hear the drain ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

The dishwasher is making a horrible noise. Could it be the motor? Tried running both drawers and same noise each time. About how much would it cost to replace motors? Would I be better off getting a new dishwasher?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1270 seconds