Having problems with your Honda Pressure Washer PSI 3000 ?

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


Answers :

Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

I recently replaced the water seals, V-packing & all six check valves in a CW-3504-4MGH pump on a MiTM 3504 pressure washer that had very low pressure. Usually this would fix most pressure problems on most machines, but in this case it had little to no effect. I suspect that the unloaded is the culprit in this case, but since I have had little experience in repairing unloaders (let alone adjusting them). I would appreciate feedback from anyone that has experience in this area. Thanks


Check the wand tip for a tiny piece of debris like a tiny rock or something stuck in the tip. ... Mi T M Pressure Washers

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

Dishwasher stop running with about a minute left to go, water still in the bottom. Following lights are blinking; high temp wash, sanitize, and no heat dry. I have check that the garbage disposal is clear, even ran it for a while. The over flow valve does move up and down. Pressing the buttons mentioned above does nothing.


I am assuming this problem has been fixed. If not then please post a comment to confirm which bit is still not resolved. ... Frigidaire Dishwashers

How do I clean the unloader valve on a Karchner model G2600VH Cannot get steady pressure from the outlet of the nozzel have clean filter checked for leaks and replaced all nozzels still having issue with flux in pressure.


Check the tips and Videos at http://www.ereplacementparts.com/karcher-2600-11944040-pressure-washer-parts-c-33388_33389_34001.html ... Karcher 2500 PSI Pressure Washer

Drain problems I have a Kenmore 665.17292992 portable dishwasher. I've changed the filter and the seals however it still does not want to drain. It will drain but extremely slowly and since it's on a timer, it only drains maybe 10% of the water out. My next step was/is going to be the Check Valve... but I am at a loss right now. I thought for sure it would be the filter. Any advice would be appreciated. Thanks, PM


This may not be the solution, but look for an air in-take somewhere on the top/back of the unit. It's probably covered by a stainless steel cover that can be taken off. Unscrew this cover and see if the air intake is blocked with lint. This is usua ... Dishwashers

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

I have a leak from the pressure washer output manifold and sears model 580752050. (pump model mtpv93517) The check valve kit Briggs and Stratton # 193806gs I ordered was correct from but the check valves are too tall to seat into the output manifold and be flush when reinstalling. Did I order the wrong check valve kit or is there another problem?


... Pressure Washers

My Maytag Model # mdb7130aww will not fill with water. I did the auto function test and it completed without any codes but when the water valve was supposed to come on, it didn't. Everything else functioned. I tested the resistance of the valve and my multimeter went from 1 to .90 or so when I checked the terminals. Also, this problem is intermittent and when I check the voltage to the valve it reads around 70 unplugged and 120 when its plugged up to the valve. Does this mean the water cont


... Maytag MDB7130 Dishwasher

Hotpoint hda3440g02sa leaves a little water at the bottom of the dishwasher I have checked the check valve have even replaced I have put a high loop in the drain hose and still no help it leaves just a little water I hate to put a new pump because I have on this type of dishwasher before and still no help


Hi\015\012\015\012 \015\012\015\012When the dishwasher leaves just a little water and drains\015\012maximum then I would say that it is fine & the drain pump is also working\015\012fine. These units are designed in such a way tha ... Dishwashers

Inlet Valve keeps stopping and starting, takes a bit of water then stops take a bit more then stops, on off on off for about 10 mins until its taken enough water to srta the cycle , have replaced the Inlet Valve still happening and water flow meter with pcb still happening Any suggestions? It a DWLT65


What about the overflow valve? It could be sticking ... Beko Dishwashers

Just installed an estate TUD6710S and on the first run it is leaking from the check valve. It is leaking from the pump side of the valve. There isn't any leak where I have the drain connected. I do not have a garbage disposal, so, there's not a problem there. The drain connection is 20" from the sub-floor... don't know what else to check.


... Estate TUD6710 Built-in Dishwasher

My Karcher 4000 SHR Pressure Washer pressure pulses when operating. I have checked with Karcher Technical Support and all their trouble shooting procedures except checking the unloading valve. Where is this valve, how do I get to it and how do I lubricate it?


It sounds like your unloading valve is crudded up with mineral deposits and stuck in a partway open state. look for a plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the ... Honda Karcher G4000RH Pressure Washer

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

Electrolux EIDW6305GS1 will not run , keeps flashing error code 11 which indicates drain valve problem. I have replaced drain valve, wash pump, float valve and reed switch but no luck, still flashin


Success....Error 11 on Electrolux dishwasher?\012 I have an Electrolux EWDW 6505 which in the start of a wash cycle would start beeping and Error code 11 would display.\012 The problem: Drain Valve (Small copper lever switch inside)\01 ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Honda GC 160 Engine, I had the carb replaced about 1 year ago, now its doing the same thing. At first it wouldnt start at all, I cleaned the carb, then it started would speed up and die. I then took the carb off and cleaned the jets, now it starts with the choke in the closed position only, at high speed it sputters and dies, but will I run it at med speed it runs but will die with tiller has a load, also when you put the choke to open it always dies. I dumped all the gas, and checked the fuel


This really sounds like a carb problem, good to hear that you are taking the carb all the way off and soaking it, this is the best way to clean a carb. I don't think it would be the fuel pump, they either work or they don't. I would check the governe ... Karcher 2500 PSI Pressure Washer

My karcher is still running even after i release the trigger and visual check i cant see any leak from outside where can i check further to solve this problem thanks in advance.


... Karcher Pressure Washers

I have a triton XL model GSD6900 that does not fill with water. I replaced the fill valve about 8 months ago. Have checked the inlet valve and coil shows continuity. Ran it thru a cycle and found no voltage at the valve. I assume the problem is in the timer. If this is the case should I have it repaired or buy a new dishwasher.


... GE 24 in. GSD6900J Built-in Dishwasher

Fuel pump not working when trigger pulled, all temp. lights on. checked flow switches all ok and new fuel pump coil an stalk fitted. the burner will work if the o ring removed from bottom of stalk allowing fuel through so something is stopping coil from getting 24v(it does get a nominal voltage of 10v)... anyone got any thoughts


... Pressure Washers

Electrolux EIDW6305GS1 will not run , keeps flashing error code 11 which indicates drain valve problem. I have replaced drain valve, wash pump, float valve and reed switch but no luck, still flashing error code 11


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0943 seconds