Having problems with your Honda Pressure Washer PSI 3000 ?

I have a Honda 11.0 HP pressure washer 3000# ,how do I remove the pump from the engine?


Answers :

Remove the bolts holding the pump to the engine. Turn the engine over to align the hole on the flange with the set screw inside holding the pump to the crankshaft. Loosen the set screw fully which is more than likely an allen screw. Now remove the pump from the engine. You may have to pry with a screwdriver to get it loose. If it still will not come off there are special holes that you can use to thread into these holes near the mounting holes to press the pump off. Just tighten them alternating back and forth until they push the pump off the crankshaft. Your pump may be slightly different depending on make.
Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers

Hello, I own a Honda Pressure Washer (Porter Cable Model) with a Cat pump 2600psi and 6.5 hp. An Excellent machine for the past 7 years. Last fall I noticed it was not producing the full pressure but still Engine was running strong. This past weekend. started it up and used it for about 1 hour still with minimal pressure at full throttle. Then pressure was totally cut off. I stopped and started the engine the engine and it had minimal pressure again. Same thing happened again. I stopped the engi


... Honda Pressure Washers

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Assembly I recently purchased a pressure washer from Home Depot. It is rated at 3100 psi. It is a comet pump with a honda gas engine. The assembly instructions recommended that I remove the plug on the top of the pump and replace it with a vented plug that was provided. However, none of the other enclosed manuls talk about the vented plug. Am I reading the assembly insturctions correctly. Should there be a vented plug ?


HI your machine would have been delivered with a blanking plug in the pump. You will need to remove this and fit a vented pump or your pump will build up too much pressure inside. ... Comet BXD2527 Pressure Washer Pump

How to remove pump from engine - Honda Pressure Washer PSI 3000


I wasn't able to find a schematic for your pump dis assembly, but here is a Link to a site that may be able to help you:www.pressu ... Honda Pressure Washer PSI 3000

I have a Honda 11.0 HP pressure washer 3000# ,how do I remove the pump from the engine?


Remove the bolts holding the pump to the engine. Turn the engine over to align the hole on the flange with the set screw inside holding the pump to the crankshaft. Loosen the set screw fully which is more than likely an allen screw. Now remove the pu ... Honda Pressure Washer PSI 3000

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

DeVilbiss Pressure WAsher EXH2425 Honda engine GC160qha pump DAPC axcial cam. When using washer sprayer both the engine and pump seem to operate normally. As soon as I let off the trigger of sprayer the engine dies. Help?


Hi and welcome to FixYa. I am Kelly \015\012Take a look at your engine parts manual here: \015\012\015\012 ... Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

I have a Husky gasoline pressure washer. The honda motor starts but stalls because the pressure by-pass (not the right term) doesn't seem to open and builds up pressure. I haven't tried to remove any parts yet. I think grit has got in but don't know for sure. The pump looks pretty simple and the part I want to remove for cleaning looks like a plastic hexagon nob. Will this access the by-pass or is it something else.


I think you're right about the knob, but try this:Open the water to the washer. Leave the line open, and hold the trigger down to get all of the air out of the supply and discharge lines. While still holding the trigger down on the spray gun, ... Pressure Washers

My troy bilt pressure washer only runs a few seconds then dies.I thought the pump was plugged so I removed pump.While pump was off I ran the engine in case it was a fuel issue,The engine ran fine.Whic


... Pressure Washers

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

I have a ANNOVI pressure washer and I can not seam to get the engine apart from the pressure pump. All bolts are removed and the bludy thing will not come apart. The lock nut on the drive is not even


There may be no good news for you. Once those hollow shaft pumps seize to a engine shaft, they can be real buggers. In fact, they can be impossible. But before you give up and completely destroy the pump to remove it from the shaft -- the ... Pressure Washers

I can't remove the pressure washer pump because the Engine Adaptor, part # 95165 will not come off. Anyone know how to remove it? The model is 580751651.


... Pressure Washers

I temporarily misplaced (not lost for good) the owners manual for my honda pressure washer : engine and pump. I do not want to run my machine again until I verify the pump oil content/level. On the pump itself, at the top, there is a black, unscrewable oil cap, with blue-ish oil in it, BUT NO DIP STICK! How do I check the level? What kind of oil, specs etc? Thanks!


Http://www.ultimatewasher.com/download/honda-engines/gc160.pdf ... Karcher 2500 PSI Pressure Washer

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

I HAVE AN EXCELL PRESSURE WASHER-MODEL EXPRO 2530-HONDA ENGINE GX200QX2-IT HAS A CAT PUMP MODEL#2SFX30GZ1. IT IS VERY HARD TO CRANK UNLESS YOU DEPRESS THE HANDLE ON THE SPRAY WAND WHILE CRANKING.ONCE STARTED IT WORKS FINE UNTIL YOU RELEASE THE HANDLE AND THEN THE ENGINE QUITS.IT DOES NOT GO INTO BYPASS MODE.


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I have an excel pressure washer 11 hp Honda engine. water is leaking into the cat pump 4hp40gl causing the oil to become milky, after the washer sits overnight the oil clears up. Any and all help will be appreciated. Thanks


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

190 honda engine only runs on choke? - Honda 50 W Ar Pump 2500 Psi 25 Gpm Pressure Washer


Pour a large amount of carburator cleaner into the gas tank \015\012run the engine for five minutes then shut it off and let it sit for a couple of days.\015\012then start it and see if it runs any better\015\012the longer you let i ... Honda 50 W Ar Pump 2500 Psi 25 Gpm Pressure Washer

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

For pressure washer Model WP-2402-SWHB, SN 10132043: With Honda engine running, or no engine running, no water will pass through the pump.


Hi If no water is passing through your pump on mains water pressure and not sucking from a barrel then it will be either a blocked nozzle,blocked unloader on the side of the pump or a blocked water filter. ... Pressure Washers

I need to know what kind of oil the pressure washer takes, I noticed it has a place for oil on the engine and another neat the pump. The product is a honda pressure wave 220 PSI Model NO 2225cwh-2


... Honda Maxus Prosumer MX5223 Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1427 seconds