Having problems with your Honda Pressure Washer PSI 3000 ?

Excel engine ic2 xr2625 the pressure relief is not working. when you release the trigger on the wand the pressure builds and kills the engine. what is not functioning


Answers :

Repair Help & Product Troubleshooting for Honda Pressure Washer PSI 3000

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Excel engine ic2 xr2625 the pressure relief is not working. when you release the trigger on the wand the pressure builds and kills the engine. what is not functioning


... Honda Pressure Washer PSI 3000

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

Lack of pressure after releasing the trigger on the wand


Hello awcockerill:This sounds like the bypass (unloader) valve is sticking. Here is a diagram of your machine's pump. On page 2. ... Karcher 2500 PSI Pressure Washer

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

My pressure washer will not start or stay running unless the trigger is open on the wand. The engine runs good until the trigger is released then the engine stalls instantly. what is worng and how do I fix?


... Briggs & Stratton 2200 PSI Gas Pressure Washer

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I HAVE AN EXCELL PRESSURE WASHER-MODEL EXPRO 2530-HONDA ENGINE GX200QX2-IT HAS A CAT PUMP MODEL#2SFX30GZ1. IT IS VERY HARD TO CRANK UNLESS YOU DEPRESS THE HANDLE ON THE SPRAY WAND WHILE CRANKING.ONCE STARTED IT WORKS FINE UNTIL YOU RELEASE THE HANDLE AND THEN THE ENGINE QUITS.IT DOES NOT GO INTO BYPASS MODE.


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

Engine dies when wand trigger is released


Re-kit the unloader. ... Briggs & Stratton 020272 Elite Series Portable Gas Pressure Washer

Does not stop building pressure when the trigger is released. It will stall the engine


... Honda Pressure Washer PSI 3000

ENGINE STALLS WHEN YOU RELEASE WAND TRIGGER - Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer


... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer

Craftsman gas powered pressure washer kills motor when you release wand trigger.


The unloader/bypass valve is jamming or defective. When you are not pressing the button the water is directed through the unloader valve/check valve to recirculate.It is common for them to corrode or for the spring to break.If it has an adjustment sc ... Pressure Washers

I have a bosch 110 plus pressure washer the problem i have is i turn on washer squeeze trigger and works fine when i release trigger and press again it wont work and trigger seems to have pressure on it


... Bosch AQUATAK 110 Pressure Washer

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

Ex-Cell VR2500 Builds Pressure but Won't Spray


I have a similar problem and diagnosed it to be a problem with the gun. I spoke to a technician that services this pressure washer and he walked me through all the diagnostic steps. The pump is working because there is pressure being built up and t ... Karcher 2500 PSI Pressure Washer

Engine dies when pressure washer trigger is released-kickback


... Pressure Washers

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Honda pressure washer cuts out when lance trigger released.


When you release the trigger the pressure inside the pump rises above\015\012working pressure. Once it reaches a set control pressure (around 20%\015\012higher than working pressure) a sprung loaded piston actuates a switch\015\012thus stopping the m ... Karcher 2500 PSI Pressure Washer

Kranzle 160t pressure washer works but full pressure drops off I then release the pressure trigger for a while and it will work at full pressure again for half a minute.


... Pressure Washers

Fluctuating pressure I have a brand new Northstar 4000 psi, which I started using today. I start the PW and the pressure is great, then the pressure drops. If I release the trigger the problem repeatsand if I hold the trigger the pressure remains low. Very frustrating when you are trying to work.


... Northstar Professional Series Pressure Washer 4000 PSI

Presure relief value not working when let off trigger on wand


Sounds exactly like the problem and the soluition you are looking for. ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1277 seconds