Having problems with your Honda Pressure Washers ?

The washer will run about 2 min. then die. i have checked the oil, air filter and gas. it has good presure when running then it acts like its out of gas by stalling and dieing. Problems with Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt?


Answers :

It is possible that the oil pressure switch is not functioning properly or you have a lighter oil in the machine than is recommended.

Post a comment if you need more assistance.
Repair Help & Product Troubleshooting for Honda Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The washer will run about 2 min. then die. i have checked the oil, air filter and gas. it has good presure when running then it acts like its out of gas by stalling and dieing. Problems with Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt?


It is possible that the oil pressure switch is not functioning properly or you have a lighter oil in the machine than is recommended.Post a comment if you need more assistance. ... Honda Pressure Washers

I have a Husky 2600 Psi 2.3 GPM Honda powered gas pressure washer. When i turn it on the motor runs fine, But when i squeeze the trigger the water is not pressurized when it comes out. How do i fix this problem?


... Honda Pressure Washers

Throttle problems Homelite pressure washer model UT80709A. bought it 10 months ago with no problems and stored it for last 9 months. Before doing so, drained gas, oil. Brought out of storage a few days ago, filled with fresh gas, oil, cleaned air filter. Starts great first try but after about 30 seconds the throttle starts visibly revving the motor a litlle at first then gradually faster and faster until it seems to flood and die. Then you cant start for about an hour and its the same story. Hav


... Homelite Pressure Washers

I have used my Honda Pressure washer 3 times over a period of 1-2 years. I could not get it to start today. I did not drain the old gas but added some new gas (which was probably a few months old). I have never had problems with a lawn mower sitting for a few months; but my guess is, this is the problem? How can I repair this?


Check the oil level in the crankcase if it just spills out the oil fill hole it fine\015\012\015\012drain tank and drain float bowl and clean fuel tap make sure the carb is not green and blocked if so give it a good clean out ... Honda Pressure Washer PSI 3000

Honda GC 160 Engine, I had the carb replaced about 1 year ago, now its doing the same thing. At first it wouldnt start at all, I cleaned the carb, then it started would speed up and die. I then took the carb off and cleaned the jets, now it starts with the choke in the closed position only, at high speed it sputters and dies, but will I run it at med speed it runs but will die with tiller has a load, also when you put the choke to open it always dies. I dumped all the gas, and checked the fuel


This really sounds like a carb problem, good to hear that you are taking the carb all the way off and soaking it, this is the best way to clean a carb. I don't think it would be the fuel pump, they either work or they don't. I would check the governe ... Karcher 2500 PSI Pressure Washer

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

New pressure washer runs starts and runs for 30-45 minutes with no problems then dies and will not restart. Once it cools for a few minutes it will restart but will die again quickly. If it is allowed to sit for 30+ minutes it will run for another half hour but then dies again. Changed oil, gas, checked all obvious areas. Any suggestions?


Try removing the carb bowl and check for dirt/water etc , also if the machine is over heating it may be getting vapour locked ... Honda Pressure Washer PSI 3000

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

I got a devilbiss power washer 2400psi wvrh2421 2.1gpm 5.5 honda engine its not getting gas and where the position for to turn on the gas


... Pressure Washers

Honda CU2400 1-MHC has been sitting in my parents garage for about 2 years. It was used once or twice. It looks new. I tried to start it and it wouldn't. I drained the gas and put new premium gas in it and it started but it won't stay running and the pressure is not what it should be. It doesn't clean as well as the electric one I used last time. So, my problem is, it won't stay running and when it is running it doesn't have enough pressure. Any ideas???


After sitting that long, I'd guess the carburetor linkages etc., are partially seized and the governor is not operating as it should to allow proper RPM's when under load. Real good chance carburetor is gummed up good too. I'd get carb serviced, but ... Pressure Washers

Pressure washer sputters and stalls when trigger is engaged


Hi k2times01It is a always a good idea to clean out the gas tank and use new fuel, however, this sounds like an RPM problem. Try adjusting the RPM up a tad and see if it runs better when you load it. If the RPM isn't the problem, you may have ... Pressure Washers

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

I have a Honda GCV160 5.5 HP engine, CV-2400-1MHC, 2400psi, 2 GPM Chore Master MI-T-M gas pressure washer, about 5 years old (the manual is dated 2005). I am the second owner and the first owner told me he did not use it very much. I just bought it in July 2010. When I adjust the nozzle the only setting that will clean my timber deck is the high pressure with the narrowest flow. At this setting it will take forever to clean the deck. The setting with a broader coverage and high pres


... Honda Pressure Washers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

My Honda pressure washer engine model GC190 is leaking gas from the carburator when running. How can I repair this problem


... Honda Karcher G2400HH-R Pressure Washer

Got a Dewalt 3800 PSI Pressure Washer with 4.0 GPM with a Honda GX 390 gas engine. Tipped it up to roll it out to my truck and got a big puddle of water with what looked like Pump oil in the puddle. Can you help???? It is less than a year old with 10-15 hours on it.....


Could very well be. Did you check the oil level and condition of oil? If its too full or if its light brown milky, then water has entered crankcase. Pressure washer pumps cannot stand to ever let run dry. Even a little. Also excessive idling will ov ... Dewalt 3800 PSI Pressure Washer

WE HAVE A HONDA ic2 EXCELL 2500PSI VR2522 2.2 GPM 5.5HP GCV160.THE PROBLEM IS OIL COMING OUT OF UNDER THE ENGINE I DON'T KNOW WHERE.


Check oil filter/sump gasket or sump oil drain plug copper washer ... Honda Pressure Washers

Where can i find a service center - Simpson Taskmaster Industrial Gas Powered Pressure Washer 4000 PSI @ 3.5 GPM Honda GX390 Engine And 50' Non-Marring Hose #TM4000BD


On the internet. ... Simpson Taskmaster Industrial Gas Powered Pressure Washer 4000 PSI @ 3.5 GPM Honda GX390 Engine And 50' Non-Marring Hose #TM4000BD

Hi I have a brand new Honda Power washer GC 160,2600 psi 2.3 GPM my husband taught me how to use it last night and I think I have followed all of steps: 1. hose free of kinks 2. connected to machine 3. purged pw handle of air and made sure water from house coming through 4. pulled out choke 5. turned red button to "ON" position 5. pulled T handle enging starter and it sounds like it will start but doesnt what am I doing wrong??? yes it does have gas in the fuel tank.


... Karcher 2500 PSI Pressure Washer

Engine will not turn-over. It is a Honda 11 HP, OHV on a Karcher Pressure Washer. It was running fine for about 45 minutes. All of a sudden it stopped. When I tried to start it again, the engine is bound up so that the pull rope will not pull out at all. It has plenty of gas. The crank case is full of oil, not over full.


Pull the spart plug out and see if you can pull it. Sometimes the carb will flood the engine to a point that they get hydrolic lock.If it does free up then I suggest cleaning the carburator before trying to start it again.If it does not free up the y ... Karcher 2500 PSI Pressure Washer

Describe your Honda Maxus Prosumer 2750 PSI Pressure Washer w/ GX & CAT Pump - MX5223 Problem keeps dying


If it has a bowl on the bottom of the carb you float might be stuck, and check if the air cleaner is dirty ... Honda Maxus Prosumer MX5223 Pressure Washer

Troy built 2350 psi 2.0 gpm. pressure washer. starts onne then dies. will not start again. has briggs and straton motor. has been sitting up for the winter. have changed spark pulg. checked air filter that is clean, has oil and gas.


... Pressure Washers

What do I use for oil in motor? - Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt


I always use synthetic oil in my small engines, and recommend it. Use 5w-30, 5w-20, or 10w-30 ... Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt

I have a reconditioned Husky 3000PSI with Honda GCV190. We used it for a couple of hours. Had to put gas in it once and it started up no problem. However when we undid the water hose and moved it to back yard we could not get it to start again. Ckd oil dip stick and was fine. Any thoughts?


... Pressure Washers

Honda GX100 gas engine will not idle, it just dies. Runs OK at WOT


You will need to adjust the low speed idle screw. Make sure the spark plug is clean before adjusting. ... Honda Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0961 seconds