Having problems with your Honda Pressure Washers ?

I poked a hole in the top of the engine right were the ohc letters are how do i fix it


Answers :

The only thing you can do is repalce the cover. You will have to replcae the gasket aswell. It is't expesive or hard to do yourself. I would ecommend covering the hole with gaffer tape or something untill you get a new part, and not using the machine as yo udon't want anything getting in there and damaging anything.
\015\012Find your local dealer on here http://ww1.honda.co.uk/common/multimap/honda_pe_xml/multimap.html?franchise=l&division=garden
\015\012
\015\012 If you are not UK then try http://www.honda.com/ and follow the links. Honda normally despatch parts to arrive next day, and all dealers can access there extranet system for ordering/pricing so you shouldn't have to wait long for the part.
\015\012
\015\012Before going to your local dealer, get the serial number and full model number of the machine. Serial number is normally letters prefix (GCAB or similar) followed by a six digit number. Check the rating for the full model number. Alot of manufacturers use Honda engines, so I would suggest making a note of the engine model number aswell (usually on the pull start housing).
\015\012
\015\012Before fitting your new parts, make sure there is no debris in the housing. Depending on the model it will either have valves/rockers there or a plastic pulley and belt. Try not to disturb these parts as they have to be set in certain positions with regards to the timing. If you are unsure take it to your local dealer for checking. IF IT HAS VALVES there is normally a small metal cap on the exhaust valve. MAke sure this hasn't come dislodged or fallen off.
Repair Help & Product Troubleshooting for Honda Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I poked a hole in the top of the engine right were the ohc letters are how do i fix it


The only thing you can do is repalce the cover. You will have to replcae the gasket aswell. It is't expesive or hard to do yourself. I would ecommend covering the hole with gaffer tape or something untill you get a new part, and not using the machine ... Honda Pressure Washers

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

The top level is not getting clean. We think the passage to the top water jet is clogged. There are two holes in the back that the washing arm fits into, depending on what level the top rack is set at, and one of them is stuck open. We have not been happy with this dishwasher from the start and are trying to decide if we should get it fixed or just buy a new one.


Sometimes it is not worth the headache.dishwashers are a dime a dozen,if you want to happy,just replace it,most dishwashers are unrepairable.no matter what the maytag man says. ... Dishwashers

There is a leak at the top of the manifold which is positioned under the engine...Is there a repair kit or suggestions for a fix. It seems as though the water is coming from a bolt at the top of the manifold. Thanks in advance for your help!


If this manifold is held on by 4 Allen head screws it is very common for the rear o-ring to become damaged and cause the unit to leak.What is the model number of your pressure washer. ... Pressure Washers

My GE Profile dishwasher PDW9980N is leaking from the top of the door and the right corner. Please let me know what could it be and how to fix it?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... GE PDW9980NSS Built-in Dishwasher

I have a Frigidaire FBD1250REQ0 dishwasher, and the top rack keeps coming off the wheels on the right hand side. How do I fix this? Also, when we push the start button the washer does not aways start. We have to open and close the door and try again, usually several times. Is this fixable?


Hello,what this simply mean is that there has been a lost or pastier connection on the power distributor from the panel to the control unit .what you are to do to solve this problem is to unscrew the washer from the screws then trace the ... Frigidaire 24 in. FDB1250RE Built-in Dishwasher

GE ZBD6800K starts with a high pitched tone while filling. Also the paint is blistering toward the top right near control panel. Can this be fixed? Is there a fire danger?


... GE 24 in. ZBD6800K Built-in Dishwasher

Have a dd603 with an issue...took off the arm and the metal silver disk (the ones with holes) to get to the wash impeller-(the thing with blue blades) the wash impeller will not spin-which I think is part of my problem, since i looked at the lower drawer and was able to spin the blue blades easily...was also able to pull it right out. Cant pull out the upper wash impeller!!!! Really want to get this fixed before my husband gets home and I get the lecture about how I purchased a cool looking d


Lol I don't know a lot about dishwashers, just do him good and tell him afterwards, and then hire a mechanic to look at it.Why would you want to pull the propellers off anyway? The top one doesn't pull off because it's screwed on, and the botto ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, our dishwasher is giving us some difficulty.it is under a year old but when we turn it on it is showing us a little tool and also the letters al appear on the top right corner,any hints on what to do?


Hi.The problem depend on the error code displayed. Contact Hobart to get the machine repaired. You are still in warranty, purchase receipt is not needed to validate warranty.See: ... Hobart Dishwashers

We have a GE dishwasher with upper and lower sprayers. The upper sprayer (one located right under top rack) won't spray or turn which leaves the dishes in upper rack dirty, any suggestions on how to fix this, will it require replacement of the sprayer arm?


Try c.l.r. to clean dishwasher check and clean lower and upper spray arms out, run no detergent you can also run vinegar in it as well about a cup full,let the machine start to run then stop dish washer for a few hours then restart see if this works ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Kenmore Ultra Wash Plus Quiet Pak Plus We have moved into a rental. It has the above dishwasher but only the letter ABC and then the dial which also just says ABC. There are two button for each letter and then a further four button to the right of the letters. Can you tell us what the ABC stand for, what each other the two button by each letter stabds for and what the four buttons to the right stand for? We have no manual the machine looks old, and any pictures that might help are rubbed off.


... Kenmore Dishwashers

Water is leaking from the top of the top drawer, mainly on the right side of the top drawer. Is there an adjustment to raise the tub so that it would have an even seal to prevent the water from leaking. I noticed that the top drawer has a bigger gap on the right side or has more give-in/movemenet when the tub is lifted compare to the left side. This casue the flooding error at the end of the washing cycle.


I have had similar problems with my DD603SS. The leakage leads to the water detection in the bottom of the unit and the resulting F1 error. The movement and height of the lid is controlled by the lid actuators. There is one on each sidewall. The draw ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Dirty Dishes in top rack, Sears Kenmore Mod. 16032 - Fixing Pump Impeller?


... Dishwashers

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Engine lockup I have a craftsman power washer with a briggs and stratton 850 series engine, craftsman model 580752220, the engine will not turnover unless i remove the spark plug, it has electric start and will turn over with no problem like this but if i put my finger over the plug hole it locks up immediatly


Sounds like the intake or exhaust valve is not opening. ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

I have a frigidaire dishwasher 4000 series aqua surge with speed clean. The small spray arm on the ceiling of the washer came off. I found it sitting on top of some cups in the top basket. There is a loose part inside the retainer in the ceiling that moves back into the retainer when I try to put the spray arm back on. How do I fix this and how do I get the top basket out to work on it?


The top arm snaps into place. Simply unscrew the retaining clip from the ceiling of the washer. Inside of there, you will find a small white plastic clip. Make sure the two prongs are pointed down and poking out through the hole in the bottom of the ... Frigidaire PLD4555RFC Dishwasher

We have a built in GE dishwasher. It has worked fine for about 4 years but now the glasses in the top rack will not come clean. I have cleaned all the holes where the water comes out but I think the sprayer that is beneath the top rack (the one that is attached to the bottom of the top rack) is not rotating. We had someone out to take a look at it and they said it was fine. It isn't fine as it is not cleaning the dishes. Is there a reason that the bottom sprayer is not turning?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Maytag Dishwasher

I have a honda GX240K1 on a BCS tiller. The engine seems to defy reason. I have adjusted the governor, set the max speed screw, adjusted the idle speed and have achieved some success but cannot seem to control max RPM's. The engine max's out at over 5K. I have tried about everything I can imagine yet nothing seems to fix it. Spec's say that it should idle at about 1400 Rpm yet it seems to idle best at about 1800-1900. I am using a EZ328 instrument to check the engine RPM and it's reading i


Hello. It sounds like the governor is either out of adjustment or in need of replacement. I agree that you should not run this in this condition or you will have a much larger repair to do. I would replace the governor. J. ... Honda 8 HP Engine

I have mod. # FDB1050REB0 the top rack wash/rise arm is not turning at anytime during the wash cycle--- We are not covering the hole into which the water is being pumped---- the bottom washing is turning---- this leads me to to believe the line to the top arm is obstructed from the pump to the wash outlet (in the top of the machine)---- what can I do to check the line?


Hi\015\012\015\012Please check if something is blocked near the top spray arm\015\012and also make sure that all holes are open. Use a sharp metal pin to clean the\015\012holes on the top spray arm. Make sure the water pressure is not low ... Frigidaire Dishwashers

I bought a house with a Bosch dishwasher in it and soon found that the top spinner holes are blocked with bits of old labels. I have removed the spinner and separated the concentric tubes but I do not see how to push the debris back along to the inlet. Do I need a power but very small jet to put into the holes along the arm? Would drying it then putting the suction of a vacuum over the inlet hole be useful?


This is very common if the filters are not cleaned regulary if you remove the arms and soak them in hot soapy water for around half an hour this should loosen the debris also tap them on the side of the sink this will remove more stubborn debris ,ref ... Bosch Dishwashers

Pump fluid coming out of breather hole in plastic cap on top of pump


... Comet AXD 3020 G Pressure Washer Pump

I NEED HELP CLEANING OUT MY FILTER ON MY HOTPOINT DISHWASHER..... WHEN WE GO TO RUN IT THE WATER STAY'S IN THE BOTTOM AND WILL NOT DRAIN OUT SO PLEASE HELP ME FIX MY PROBLEM CUZ I CANNOT AFFORD RIGHT NOW SOMEONE COMING OUT TO LOOK AT IT SO IF I CAN FIX IT MYSELF THAT WOULD BE GREAT AND WITH YOUR ALL'S HELP IF YOU WILL THANKS ALICIA


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Design Flaw I had the same problem. While under warranty they "fixed" the problem by putting in a zip tie (no joke) to keep top spray arm from rattling. The tech said they were working on a resolution of the design flaw. Then, when the zip tie broke I called them again. This time they replaced a small o-ring where the water line comes into the top spray arm. The o-ring eventually fell off. When that came out for the 3rd time, they re-ordered the same o-ring. Now again, I am having problems with


... GE 24 in. GSD2120C Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0996 seconds