Having problems with your Honda Pressure Washers ?

My Honda Excell 2400 psi EXH2425 pressure washer starts and runs pretty smooth but I can't get very much pressure in the spray. I have used carburator cleaner and the air filter looks alright, aside from a dent in the filter. Any other ideas? Thank you!


Answers :

It sounds like the unloader on your pump is going bad but it is hard to say if it is that or the valves in the pump. The only issue with this machine is that parts are no longer available for this pump. The only option I really have for you is to replace the pump with a new one, it is a very simple process and only takes about 15 minutes to complete.
\012
\012See this link for information on the pump that would fit your machine
\012
\012The only thing else you might need is a coupler to have the hose adapt onto this pump
\012
\012See this link for the coupler
Repair Help & Product Troubleshooting for Honda Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Honda Excell 2400 psi EXH2425 pressure washer starts and runs pretty smooth but I can't get very much pressure in the spray. I have used carburator cleaner and the air filter looks alright, aside from a dent in the filter. Any other ideas? Thank you!


It sounds like the unloader on your pump is going bad but it is hard to say if it is that or the valves in the pump. The only issue with this machine is that parts are no longer available for this pump. The only option I really have for you is to rep ... Honda Pressure Washers

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

I have a 7 hp B&G craftsman Pressure washer , if I place an air filter on it ,it wound't start or run , if I remove the air filter it would run like a champ, but after 10 mints , oil would shoot out off the carb like a running faucet , why is it not running with the filter on,.Now am not so sure if the air filter is the correct size , because when I put it on it seem to be a bit on the taller size rather than a perfect fit, thanks for your help , in Hollywood , Reinaldo Roman .


First,It sounds like the air filter is full of dirt preventing air from flowing through, starving the engine of air.As for the oil shooting through, are you certain the oil is coming from teh carb?. Makes no sense the engine w ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a troy built pressure washer leaking gas from the air filter i looked around for advice and hurd bang against the carb and it will realease the float valve i did it and it worked but should i clean out the fuel in the filter area or the filter will it harm it as it is or should it be okay? the filter was soaked in gas dry now and when it happened the gas flowed from the air intake (behind the filter) if i need to clean out in there how do it do it and if i need a new filter


Definetly replace the paper filter and yes Lowes will carry them.if it does not leak now, I would leave it alone or you will be installing a nine dollar kit.The briggs kit # is 294260 is you choose to do it anyway ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Hi. I'm scratch building a pressure washer using a Comet BXD2831G pump. If I don't plan on using any type of detergent, is it OK (or manditory) to plug the detergent intake to keep it from sucking air? I would use a short piece of hose over the intake with a screw in the opposite end. Also, is it possible to set the pressure by ear? If so, what should I listen for? Thanks for your help!


No need to plug the injector because under pressure (internal force/pressure) keeps valve shut. It only opens when large nozzle (black tip) is used lowering internal pressure causing siphon effect. Some chemical injectors have a thumbwheel ... Comet GXD2527G Pressure Washer Pump

Hi I have a flavel dwf640 w dishwasher and since i've had it it doesn't seem to be washing the dishes properly at all, glasses are all smokie looking, cutlery are all grey looking and its not taking the tea and coffee stains off the cups. I use finish powerball tablets and salt and rinse aid , i also have cleaned out the filters and used a dishwasher cleaner, and yet this is still happening, most of the time i have to scrub my dishes first and leave my cups and glasses and cutlery steeping to g


... Dishwashers

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

I have been negligent in not cleaning out the filters and after the unit more or less stopped, I pulled the two filters finding them full of what looked like soap scum. I cleaned them best I could (but noticed the inner filter still had most of the small holes blocked) Started the unit and it cleaned alright for a couple of days. Last night after running a load all the water did not empty from the bottom of the tub? Any suggestion on what wrong? Bought the unit on 1/19/05. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Odor We have had our electrolux dishwasher for a year, recently we are experincing a very strong rancid odor inthe dishwasher and around the sink. I have used disposal cleaners, but it does not appear to correct the problem, is there something I need to be looking for internally? (I have looked inside the trap and there is sitting water but nothing within the filter that would warrant this smell.


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I'm using a Dewalt 2800 power washer and someone set it on its side. And now it will not start. The air cleaner is full of oil. I think there is oil in the carb. I took the air filter off and almost get it to start. Any help?


Take the air filter off and wash in petrol.allow to dry,and put back on. then take the fuel bowl off and clean.turn fuel tap on and drain fuel from carby for a few seconds.turn fuel tap off.put fuel bowl back on.then take spark plug out and turn moto ... Dewalt 3800 PSI Pressure Washer

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

My homelite 2200 pressure washer leaks fuel outta the air filter area. There's a brass, looks like a bulb, fittting underneath it with holes for 2 brass screws, only one screw is in there and the other empty screwhole is where the fuel pissin outta. Just bought earlier today, when I ran it, I only got a few minutes usage. Should there be a screw there perhaps? Is it missing?


... Homelite Pressure Washers

Pressure washer has been sitting up for about 2 years.. worked perfectly before I parked it.. lol.. But, I put a new spark plug on, cleaned the filter, sprayed carb cleaner in it drained the gas tank and added new gas.. But it still does the same thing.. It starts in the choke position, runs awhile, and then shuts off. While its running, I tried to put the switch in the run position and it kills. Just wanted to see what an expert would say about the matter before I Brake it down. thanks


... Briggs and Stratton 020275 Elite Series 3400 PSI Portable Gas Pressure Washer

Recently there's been a white coating on dishes. Has to be scrubbed off manually or soaked in a vinegar/water solution. I flushed out the rotating arms to be sure water flows thru & it does. Checked bottom filter & basket...both clean. Twice used "finish" cleaner for dishwashers in the scrub cycle as directed. Turned off during drying cycle and now there is water across the bottom of the dishwasher. Next? Thanks for any help. Rosemary


Use any brand of dishwasher cleaner from a local store and run your dishwasher with it.I would also recommend that a calcium lime and scale remover be ran through your dishwasher to clean it out.\012this may have to be done a couple of times. ... Kenmore Dishwashers

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

B/s lawn mower, when primed engine starts but stops when petrol is used up.I have cleaned air filter, which looked ok to no avail.


Your description sounds normal, gas engines stop when guel is used up, but I presume that you meant after the prime fuel is used up. This sounds like a fuel delivery problem, and most likely within the carb itself, you need to disassemble and clean o ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have a Jenn aire jdb8910aww dishwasher and after every type of treatment and cleanser I still cannot get the powdery residue to go away. The only thing that works is white vinegar, but i have to use it in every cycle. I even have a water filtering system in our home. What could be the problem?. Thanks, Michelle


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Jenn-Air 24 in. JDB8910 Built-in Dishwasher

Hi, I have a white film on my dishes when I use my dishwasher,and my water temp is set at 130. We have a water filter system and have lost water pressure because of it. Do you think this could be my problem are do I need to raise my water temp? Thanks


What does this mean?: "yea youre no help"\015\012\015\012It sounds like whatever type system you have (sediment filter, neutralizer, softener, etc.) needs maintenance. It's releasing something undesirable into your water. ... Whirlpool Dishwashers

I just bought a 3-3050 pressure washer and after using for about 2 hours I have developed a bad gas leak out of the carburator seal area. The bolts were on tight and I am perplexed. I contactacted CPO and they recomended sending it back. I'm in the middle of painting my house and was wondering if ther was a easy fix to this probem--thanks Bill


No quick fix. You have to replace that seal ... Karcher G3025OH Pressure Washer

Starts but won't stay running, i clean carburator and still have same problem, unit has been used very little, still look new, Thanks,


Have you checked your oil? You need pump oil half way up in reservoir. Open plug on top of pump and check oil. Pump takes SAE 20 or 30Next, open oil plug below engine and check your oil level. It should come up 1/2 way on dip stick. Engi ... Honda 2500 PSI Gas Pressure Washer

Pressure washer has been sitting for 6 months only runs when i prime thru air filter the book says the alchol in fuel can be problem where i can i get a carb rebuild kit thanks


... Karcher 2500 PSI Pressure Washer

I have a Briggs & Stratton Pro 3400 pressure washer that I got new last year and used for maybe 5 hours and it worked great. Have had it stored since then with stabilizer in the gas (I didn't run it dry) and now it won't run for more than a minute or two without dying. A dealer said it was probably bad gas and I now know that even with the stabilizer I should have run it dry last year before storing. Everything is like brand-new including plug and air filter so it must be the gas/carberator gunk


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

No pressure HOSE IS BIG ENOUGH,NO KINKS, FILTER IS CLEAN. TOOK THE PUMP APART AND CHECKED ALL THE CHECKS, THEY WERE ALL OK.WHAT ELSE CAN I LOOK FOR? THE PUMP IS A KARCHER-MODEL G 1800 LB Thanks, Art


Brother Art,\015\012\015\012Try this trick; it always works for me. Assemble the garden hose to the washer, install the HP hose, turn on the water. Now, make sure that there is no air trapped in the garden hose. Manipulate so as to dir ... Karcher Pressure Washers

My Honda VR 2522 on Excell 2500 psi pressure washer run good when in use but when i release the trigger on the wand the motor idles and begans to pulsate, hit and low. Where to i start looking to repair. I have a new air filer installed Roy


... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1059 seconds