Having problems with your Honda Pressure Washers ?

Does not get up to pressure engine runs fine any suggesting thank you


Answers :

If the engine is turning and running OK then its one of two differant problems . The first is it could be that one of the valves inside the valve body is stuck or something is inside keeping the valve from seating properly somethimes the cages brake and get stuck in there . Its made of plastic and likely if removed the valve will work correctly again .If you look at the valve body you will see caps most of the time brass the valves are located under these caps take them off one at a time being careful of the Oring seal all it takes is one of them to create this problem . The other thing is called the unloader valve . Its located derictly under the pressure control knob and is 4 or 5 inches long . What it dose is allow the water to recurlitate thought the body when the trigger is off so the pressure dosn't build up and blow something out . There is a relief valve but that is tempature sensitive works more like the thermostat in your car and most blow at 145 degrees . If the unloader valve is not moveing then the mechine just runs and never will build up pressure . The problem is most of them especaly on smaller mechines are not serviceable and need to be replaced as a unit you can't even take them apart . The good news is most of the time if you take them off and spray light oil into themlike WD40 and work them back and forth they can be cleaned and will work with out any other problems . You should regeralr turn this knob and during winter storage the valve body should be filled with antifreeze with a lubericant . 9 out of 10 times if you check these things it will fix the problem and woun't cost you anything but some of your time . Let me know gal per min and max pressure output [email protected]
Repair Help & Product Troubleshooting for Honda Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Does not get up to pressure engine runs fine any suggesting thank you


If the engine is turning and running OK then its one of two differant problems . The first is it could be that one of the valves inside the valve body is stuck or something is inside keeping the valve from seating properly somethimes the cages brake ... Honda Pressure Washers

I have a Generac 2300 pressure washer that has not been used for a couple of years. The engine runs fine but I get absolutely not increase in pressure when I press the trigger on the sprayer. Where should I start trying to diagnose? Thanks, Mike


... Pressure Washers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

My pressure washer was running fine then bogged out.The person who lent it to me said dont worry about the oil it is fine, so i didnt check. I checked the oil and it was almost bone dry. So i filled it with oil but now it wont start, is it possible that the engine is siezed up or, can i get it running.


You probably helped destroy the engine. Honda's are great engines until they run low on oil ... Karcher 2500 PSI Pressure Washer

Husky ran great for couple of hours. Now no pressure at all. Water comes thru for suds, but no near enough. Engine runs fine but will not build pressure. Checked for trash blockage-all clear. Thanks, Ed [email protected]


Same old problem... water admitance valve sticking.\012\012Remove the valve spool and clean the bore with crocus cloth on a dowel rod.\012\012Replace O rings and lube lightly with plumber's grease. Reassemble... good as new! ... Honda Pressure Washer PSI 3000

Low Pressure The output pressure seems very low. No crimps in the hose, the engine runs fine, the nozzle seems "open". Any suggestions?


... Honda Black Max 2600 PSI Pressure Washer

DeWalt DPE3800X runs fine for 10-15 minutes but after it warms up, it shuts down and is very difficult to get running again. I expect that there might be an issue with the pressure valve but can't be sure. Any suggestions?


... Dewalt 3800 PSI Pressure Washer

Model she44c02uc; 2 years old. no matter which cycle we pick, it just keeps on running..it gets down to about 15 minutes on the countdown timer, and then resets itself to 80 minutes or so and washes over again...if we manually turn it off and then push quick wash, it seems to finish, but doesn't dry the dishes.......we have tried all suggestions in the manual and cleaned both filters; the line is not clogged...the sink and disposal both work fine. thanks


Hi,gibpru,ngafm at your service,You said, no matter which cycle you pick, it just keeps on running..it gets down\015\012to about 15 minutes on the countdown timer, and then resets itself to\015\01280 minutes or so and washes o ... Bosch Dishwashers

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer

Power washer loses pressure. Engine runs fine. Taking the nozzel off, squeezing the trigger, and then putting the nozzel back on sometimes remedies the problem. How do I fix it? Thank you.


Your bypass valve is jamming. All you do is take it out, put a smear of o ring grease around the o rings then put back in, make sure you push it all the way in and should fix the problem. ... Karcher 2500 PSI Pressure Washer

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Appliance had been working fine now all of a sudden no water is running in the dishwasher.The machine appears to run through all of its cycles but without water. The water pressure in the ajoining sink appears a little low though the water pressure in the rest of my home is fine. I see no water leakage anywhere. Do I need to call an appliance tech or should I call a plumber? Thank you.


... GE GSD1000 Dishwasher

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

13 hp honda pressure washer 3000 psi 4gal/min Hard to start and dies out after 20 seconds after the engine gets hot and running after multiple starts the engine will stay running but then dies every 30 minutes


There are a couple of things that can cause this problem. The first thing to check is if you are loosing spark. Dying after it gets hot sounds like to stater is failing in the engine. If you loose spark this is more than likely the issue. If you are ... Honda Landa PG 3500 PSI Pressure Washer

I have an 1800 psi coleman gas washer that worked fine,then the next time i went to use it no pressure.motor runs fine,good water pressure just will not build pressure thanks dave


... Coleman Pressure Washer PW0881800

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

My 1 year old gas powered Husky model HU80432 starts and runs fine but gets no pressure from the wand. Water is running freely through all connections and hoses so there are no obstructions, just no pressure, the water just shoots out in a thin stream for about 3 feet. I stored it inside for the winter so there were no freezing issues. What's wrong?


Lime/calcium build up in the pump.\015\012Pour a large amount of liquid TSP into the fresh water inlet and let it sit for two or three days, the longer the better.\015\012This is how I fixed my no pressure problem.\015\012Works gre ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1597 seconds