Having problems with your Honda Pressure Washers ?

How to replace piston rings on honda 6 horse motor

\015 How to replace the piston rings on 6 hp honda engine for pressure washer ?\015

Answers :

You need to remove the pump then the end cover from the engine remove the cylinder head the unbolt the connecting rod push out the piston hone cylinder and then wash the motor out with soap and water i use tide clothes soap and hot water put it back to gether now why does it smoke check the head gasket the over head engines blow head gaskets and **** oil from the crankcase
Repair Help & Product Troubleshooting for Honda Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace piston rings on honda 6 horse motor


You need to remove the pump then the end cover from the engine remove the cylinder head the unbolt the connecting rod push out the piston hone cylinder and then wash the motor out with soap and water i use tide clothes soap and hot water put it back ... Honda Pressure Washers

Whats the piston ring gap - Honda Gx390 Motor Inside Cover


... Honda Gx390 Motor Inside Cover

Have a Kenmore Elite Dishwasher (66513123K701). Was not cleaning dishes very well so we ran diagnostics on it and found a problem with the diverter motor (W10155344) so we replaced it. Now, the dishwasher is leaking from the diverter. There was a o-ring from the original diverter that we had to keep since the new motor did not come with it. Wondering if we should get a new o-ring/seal, but I cannot find mention of such a part anywhere. Is there a certain way to seat the o-ring? Is it ok to


I have experienced the same diverter motor leaking problems. I have the whirlpool gold with the diverter motor (w10155344). I bought the unit new 4 years ago. The fix is remove the the two screws that hold the diverter motor and pull the motor. ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

XR2750...PROB=NO OUTPUT REMOVED BRASS PUMP FRM. ENG. PISTONS WORKING OK FOUND "O" RING IN CENTER OF PISTON ARRAY SPLIT-REPLACED NO CLOGS THAT I CAN SEE EXCEPT IN CENTER OF "O" RING IS THAT THE ONLY INPUT OF WATER TO PISTONS?


... Honda Maxus Prosumer MX5223 Pressure Washer

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Rebuilt honda GC160 5hp engine for a power washer and only got the engine to start once. Just took apart and saw that the cylinder and piston was all scored up again.


... Honda Pressure Washers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Troy built pressure washer won't start. It has a Honda 160 CVG motor. I used it for about a year and then it stopped working. I've replaced fuel and spark plug. Spark plug is soaked every


... Karcher 2500 PSI Pressure Washer

HOW TO REPLACE PISTON O-RINGS IN A CRAFTSMAN PRESSURE WASHER 580.752342


... Pressure Washers

How to replace low oil sensor on a honda gx160 motor


... Honda Pressure Washers

I have a Troy Built 2500 PSI pressure washer with Honda 160 CVG motor. It won't start. I've replaced the gas and spark plug. Every time I pull the spark plug out it's soaked. Not sure


... Pressure Washers

Won't start I have checked the spark plug and I have good saprk. I have checked the fuel sysstem and the primer bulb injects fuel. I have removed the head and cjecked for engine damage and all cycle correctly. Vaves opne on time piston shows no dmagae. side walls are smooth and not damaged. This engine was working fine but the pressure washer needed some O rings replaced. I have tried to start it with and without the pump attahced. Evrything on the engine looks fine. I removed the spark plug and


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

Mdb2400awe dishwasher motor o ring replacement


... Maytag Dishwashers

Unit is leaking. Just bought it used, runs fine but leaks water out the bottom of the motor. Can this be repaired ? Is there a gasket or o-ring or something to replace ?


It might be the pcv(positive crankcase ventilation) valve. Go to a parts store and ask for a new valve($5-$10) and also ask where it is. It's usually right on top in the back of the engine where you described. If the hose is all cracked then yo ... McCulloch FHH18A Electric Pressure Washer

I have a Coleman powermate clean machine pressure washer 2500 psi 2.36gpm and has a 6x200 honda 6.5 horse motor. I just bought at a garage sale.It started just fine when I got home and in less that 2 minutes quit. It says the engine will stop automatically when low on oil. what kind of oil should I use and for the pump what kind of oil do you use?


... Coleman Pressure Washer PW0881800

Looking for replacement hose for a Simoniz 2500 gas pressure washer with a five H.P honda motor .


... Karcher 2500 PSI Pressure Washer

Cam replacement and timing on a Honda GC160 motor


... Honda Pressure Washers

Where can i find pricing an parts for a pressure washer model 01903? honda 5.0 horse motor,2450psi/2.5gpm??


... Karcher 2500 PSI Pressure Washer

My Maytag model mdb9600aws motor shaft seal is leaking. How do I remove the seal and replace a new one. I am a novist, but I have taken the motor completely out and replaced the seal / gasket that the motor sits in, but there still is a leak. I am afraid the leak is going to destroy the motor as it has corrosion / salt like stuff about the motor. I have attempted to pry the shaft off with the use of 2 screw drivers. I was thinking since I am going to replace the whole motor shaft seal and chop


You are wise to realize the leak would destroy the motor.Take a close look at the diagram to see everything that gets placed on the motor shaft. That should give you a good idea what can/must be removed from that shaft. ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Blown Motor DW is about 16 months old. Started making some real bad noise. Lasted about a minute and then had a death howl. Called in repair tech who says motor is blown. $399 for repair which includes $125 for the part. I've rebuilt car engines, so can probably replace a DW motor. Any insight on how to replace the motor? is it worth paying 275$ for labor? Just bugs the hell out of me paying $400 bucks for a repair when i can get a new one for $450.


I haven't changed that particular brand of dishwasher motor, so I cant give a step by step, sorry. I do know the other brands it is optional to get the motor alone or the motor with the pump assembly attached, so you may want to ask abo ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

We need to replace the locking ring in the bottom of our Asko 1716 dishwasher.(It's cracked) I can only find one kind of replacement ring for that,but it looks like the right size. I need to know if Asko uses one ring for more than one model of dishwasher?It's a 5" locking ring for the bottom well of the tub. Thanks for your help!


Only 1 size ... Asko D1716 Built-in Dishwasher

I am replacing a frigidaire dishwasher washmotor. Everyone and videos tell me how to replace the motor. In the instructions in the box they say replace the sump bottom also. Why would i have to replace the sump also and not just the new motor?


Hello, chris\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take some ... Amana ADB1400AWB Dishwashers

I have a Kenmore Dishwasher Model #665.168790000 and the water fills just fine and empties fine when cancelling cycle but when pressing any wash cycle the pump/motor just makes a loud humming noise and does nothing. I took apoart the lower assemblies to clean everything out but the problem hasn't gone away. Do I need to replace the motor or the whole motor assembly (also contains impeller kit)??? Also, I don't think I need to replace the whole sump & motor assembly do I???


... Kenmore Dishwashers

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

I have a problem that appears to be a bad motor on a Whirlpool dishwasher. The motor costs $300 and the dishwasher is about 6 years old...Does it make sense to replace the motor or just replace the whirlpool diswasher (18 in unit = $600 new)...your thoughts?


Hello, W/D here.I try to work replacement vs. repair like this:If the cost of repair is greater than 50% of replacement, I always go for the replacement. My reasoning is that the remainder of the appliance is more likely to develop fault ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0872 seconds