Having problems with your Honda XR2750 powetr washer ?
how to trouble shoot low water pressure on my Honda XR2750
Engine cranks. No clogs in the lines or heads.
Repair Help & Product Troubleshooting for Honda XR2750 powetr washer
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure
What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers
Craftsman pressure washer with honda engine. low pressure and volume on high pressure setting. lots of water volume on low pressure setting. Screens not clogged.
Sounds like pump is not making pressure. Thats why you get flow, but no pressure.\015\012If it sat for awhile, check shaft connection to pump. Sometimes the impeller or shaft will shear partially due to corrosion when stored. Seals on pump valv ... Pressure Washers
Honda CV-2400-1MHC pressure washer has low water pressure.
... Pressure Washers
I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?
... Honda Pressure Washers
Honda pressure washer model # exhp3640-1 3600psi 0=13hp has low water pressure out of triggers motor does not engage for higher pressure
... Pressure Washers
I have low water pressure on my 5hp honda pressure washer
The seal dry up inside if not stored properly ... Pressure Washers
Honda GVC 160 lost pressure - noticed small black valve (back - rear) after pressure builds up , short spray then nothing - hot water comes shooting out the black valve - did something pop off?
The small black valve is called a thermal relief valve. If it is open you will have no pressure. If the water is getting hot enough to pop that valve, there might be internal problems with the pump. ... Karcher 2500 PSI Pressure Washer
I have a landa hmp-4-3500 heated pressure washer and i am problems with the water heater. where can i find a trouble shooting guide for this machine
Landa does not have a model HMP so I am not sure which machine you have. If you can provide a full model and serial off of the model tag on the machine I can provide you with a digital copy of the manual you are looking for.Sincerely, ... Honda Landa PG 3500 PSI Pressure Washer
Karcher G2600 VH - low water pressure
If the spill valve activates is "spills" water under the washer. There is a restriction or the pump has become inefficient and will not pump the volume and pressure it should at full RPM. ... Karcher G 2000 MK 2000 PSI 20 GPM 87cc Gas Powered Pressure Washer
Honda 3600 psi 0-13hp model # exhp3640-1 has low water pressure
... Honda Pressure Washers
The top rack isn't getting clean. Is it needing something cleaned out, or is something not sealing and taking the water pressure up to the top rack? How do I trouble shoot this. I already tried running an empty load with white vinegar...
Good evening. The white vinegar was a good start. It may not have helped the problem described, but will help clean out the lower end of the unit. Look for plugged nozzles and slots on the arms. Remove the arms and wash backwards through th ... Maytag 24 in. MDB6601AWS Stainless Steel Dishwasher
I'm trying to find out how much oil should be in the water pump of a honda pressure washer model xr2750-1
It's an ex-cell pressure washer with a honda motor.engine oil capicity: 0.61 qts(.58L)view owner manual here:http://www.excellpressurewasher.com/documents/pdf/a12338-e.pdf ... Honda Pressure Washers
Low pressure While I initially get high pressure, when I resume washing after having released the trigger, water pressure is low. By removing the nozzel tip and reinstalling, high water pressure is resored. What is happening?
If this keeps happening repeatedly it sounds like you need a new seal kit put in it can be done easily enough by you or you can get a shop to do it , if you live in a cold winter climate be sure to winterize the washer every year or keep it somew ... Karcher 2500 PSI Pressure Washer
I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.
Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers
I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help
This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer
Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl
... Karcher 2500 PSI Pressure Washer
I have a Honda gc160 5.0 pressure washer. All fluids are fresh. Water is hooked up with plenty of pressure but the water pressure is up and down then goes completely out. No water will come out of the wand? Please advise. Thank you.
Needs new pump ... Karcher 2500 PSI Pressure Washer
Water pressure? I read somewhere that low pressure of the incoming water will make it so that the items on the top drawer will not be as clean. I don't see how this can be the case, as I thought that the way the washer worked was that the washer filled (at whatever speed) and then the machine itself pumped the water through the system at the appropriate pressure. Please clarify.
Mom...not true. The water fills the machine which then uses its own pump to spray the dishes with the water/detergent. If your dishes are not getting clean, use the recommended amount of detergent. Hard water will require a spot treatment like Jet ... KitchenAid KUDR01TJ Dishwasher
Appliance had been working fine now all of a sudden no water is running in the dishwasher.The machine appears to run through all of its cycles but without water. The water pressure in the ajoining sink appears a little low though the water pressure in the rest of my home is fine. I see no water leakage anywhere. Do I need to call an appliance tech or should I call a plumber? Thank you.
... GE GSD1000 Dishwasher
Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots
The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers
Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!
You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer
Briggs & Stratton 2200psi/model 020228 siphon hose shoots water out when using high pressure nozzles
... Briggs & Stratton 2200 PSI Gas Pressure Washer
I have a mod. GSD2200G00WW . It has low water level and not enough pressure to turn the spray arm. When first starting i see water coming in but not enough. I added water in manually with a container and turned on and the spray arm rotated fine. I closed the door and turned back on and the water drained out of it instantly back to a low level. What now?
... GE Dishwashers
2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx
It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers
I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller
Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers