Having problems with your Hoover HD95M Free-standing Dishwasher ?

Hoover dishwasher HD95M is sticking between numbers 3 and 4 on the dial, and programme does not move on unless dial is turned to 4. Pump seems to be working


Answers :

Repair Help & Product Troubleshooting for Hoover HD95M Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover dishwasher HD95M is sticking between numbers 3 and 4 on the dial, and programme does not move on unless dial is turned to 4. Pump seems to be working


... Hoover HD95M Free-standing Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

My Candy CD474 dishwasher seems to get stuck on some of the programme setings. It sounds like it is still working however the dial does not move on. The cycles are also tking longer than expected


... Candy Dishwashers

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

I have a Zanussi Dishwasher DW907 age 10 years. The PROGRAMME SELECTOR DIAL became very stiff to operate,to start washing cycle, finally something seemed to snp and Dial now moves freely but not operating the programme of washing. Where can I obtain a replacement Dial and correct the Dial movement? I live in Ombersley, half way btween Worcester & KKidderminster.


DEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012I am happy to be of assistance!\015\012\015\012\015\012\ ... Zanussi Dishwashers

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

Hello my dishwasher seems to only do half a job at a time (and the timings for the programmes have increased dramatically). It will do a programme, but not drain, leave a puddle and leave everything dripping wet (no drying) then if I press reset the machine will drain (so the pump is working) but after resetting the problem remains and the programmes continue to not work properly. Can I solve this myself, or is this a problem with the 'computer'? Please help.......!


... Siemens Dishwashers

My stupid Candy CDI45 refuses to work when I turn it on and try to select a programme. It seems that the PR button (to select a programme) doesn't work anymore. Anyone?


... Dishwashers

Elba dishwasher (turn dial model) under 2 years old, this will be the 3rd time this has occured. You turn dial to preferred setting and press power it pumps out continuely and wont move to next stage, i have tryed reseting but to no avail please help, I will not be buying another F&P product again.


Your unit has had a "brain aneurysm" IE: Your Microprocessor has failed...Either a fix or a new one? ... Dishwashers

I have an shx65905uc bosch dishwasher that runs and works except for that there is not enough water pressure to rotate the top wand or operate the top sprinkler. The bottom wand does have water and turn and does the top but it is not enough to turn it. If i remove the bottom wand and plug it off then the top will work properly. I have cleaned all screens and removed the plate to access the pump and all seems fine. Any Thoughts


... Bosch SHX65P05UC Dishwasher

I have a Jenn-Air JDB9910AWB dishwasher. The problem I am having is everything seems to work fine until the drain cycle. It sounds like the pump is frozen. After selecting the drain button you can hear a click in the control panel followed by a 1-2 second growl in the pump but it doesn't turn or pump. I am assuming the pump runs in reverse for draining? Is it safe to assume the pump is bad?


... Jenn-Air JDB9910 Dishwasher

The dial on my model#DU8016XB-1 is frequently VERY difficult to turn, causing me to think I will break it. Once I am able to force the dial to the START position, the dishwasher cycle seems to work just fine. Can the dial be fixed? Thanks, Bob


HI. Unfortunately, this damaged timer control module will need to be replaced. This type of device is not designed to be repaired. The timer motor mechanism is damaged, thus, causing theses issues you are experiencing. Apparently, part of the timer d ... Dishwashers

Newdishwasher installed October. Seems to be making "put putting sounds" clicking noises. Programme just not moving on. Filters clean. Shouldnt be kinks anywhere, as the machine has worked great since installation, and hasnt been moved atall.. Machine is AEG Favorit 35020 V1


... AEG Dishwashers

Our asko dishwasher won't stop pumping out. The drip tray underneath fills with water and floods out. It doesn't matter where you turn the dial it is stuck in the pump cycle. When you empty the drip tray it works again for a while then the same happens again.


You have a leak. only way forward is to take of the panels and look for it ... Asko Dishwashers

New apartment. The dishwasher won't work nothing moves inside when u turn it on. The dial in the front slowly turns and the base fills up with water and that is it. Encore model 363.16129100. Was hoping I was missing something simple. I do switch the lock closed before starting . Thank you any help would be appreciated


The movements are caused by the water pump inside sounds like the pump is jammed or bad.see if the propeller looking pieces turn free by hand if so the pump is not working. you could try and see if there something stopping the pump if you feel ... Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

1)My Candy DFI 50 is not washing properly, it leaves residue on the pots. 2)The programme controller on my DFI 50 seems to be sticking. Sometimes the dial doesn't move at all or takes 'hours' to run a programme. Thanks


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Candy DFI Plan Built-In Dishwasher

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

Dishwasher was making a loud hum. I turned it off and started it this morning. Seemed to be working fine, but after about 5 minutes it started making the same loud hum. The first time it seemed to be between cycles with no water, this time there water moving as normal except for the loud hum.


... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

HELP!!. Have an old smeg dishwasher - SNZ10. We turn it on, and it goes, but the dial never moves on through the cycles - it just stays stuck wherever you have turned it to. Does seem to be heating and water coming in. Husband grumpily doing dishes by hand! HELP!!


After a while thje dial on Dish Washers, wear out and jam, It sounds like it needs a new Timer, However if it's old, I would replace the Dish Washer. ... Smeg CSU2001 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 630.17303406) and it just stopped working. Doesn't drain what's left in the bottom and just makes a humming sound when turned on. Power is good, sounds like the motor is working. Doesn't seem like it is drawing water in. I want to check the pump and motor, anybody have any advice?


If nothing obvious like blocked / obstructed outlet pipe\015\012You need to check if the outlet pump motor in line with the outlet hose is spinning when in the outlet mode. First check if it is spinning by looking at it and see if the small fan ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1605 seconds