Having problems with your Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher ?

Hi the dishwasher is leaking from the back of the machine, problem is I cannot get the machine out to see or fix the problem as i cannot unscrew the rear feet and dont want to pull too vigorously as i would break the feet. Any suggestions?


Answers :

Repair Help & Product Troubleshooting for Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi the dishwasher is leaking from the back of the machine, problem is I cannot get the machine out to see or fix the problem as i cannot unscrew the rear feet and dont want to pull too vigorously as i would break the feet. Any suggestions?


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Machine does not heat up. The water remains cold and the cycle takes hours irrespective of the setting temp. Heater seems to be OK and a tech guy repleced the sensor today as he thought that was the problem after everything else seemed to checkout ok but still no go. It has already cost us 200 dollars and I dont want to keep spending money having tech guys guessing the problem. Any suggestions? Thanks


Depending on the model, I have had loads of Bosch dishwashers fail because they have blown the heater relay solder joint on the main control board. Usually just requires control board to be opened up, and the faulty solder joint re-soldered. Occasion ... Bosch Dishwashers

My hobart dishwasher fxd200 doesn't want to fill with water anymore... What could the problem be and any suggestions? Have just had other expensive repairs done and don't want to spend any more money on this old machine if it is not worth it


... Hobart Dishwashers

I have a fisher & Pakel dishwasher and it appears to have brown a fuse inside the machine which means it does not work at all and the problem occurred during the wash cycle. This means the seal (which is a top piece that's lifted and lowered by two motors. When the seal is in the lowered position it creates a complete seal but it also locks the drawer (single drawer dishwasher) so it cannot be pulled out. I repaired the dishwasher two years ago. One of the lifter motors didn't work. I replaced t


According to the service manual there is no problem in manually forcing open the drawer in the situation where the power has failed part way through the diswasher cycle.\015\012\015\012The problem is that once you force the lid open, you ... Fisher and Paykel Dishwashers

Just purchsed G1173Vi - failed to fit due to exiting pipework on wall being directing in line with the inlet hose which is located directed above the waste hose. Had no problems fitting previous 2 dishwashers, is this common? Pipes are sealed to the machine Can you suggest a solution? obviously I cannot move exiexisting pipework.


Hi there!\015\012\015\012You say - "obviously I cannot move exiexisting pipework."\015\012, but I would consider it necessary if you need to fit this machine.\015\012\015\012The only other option is to fit a diferent m ... Miele Dishwashers

My one month old dishwasher keeps flashing the red light that indicates inlet/drain problems. I have tried what they suggest in the manual and I have rung miele and was told to reset the machine, but I am about to pull it out and leave it on the side of the road. Please help!!!


You have not mentioned Model of mechine. by the way,\015\012you can visit following website which helps you to find out exact problem.\015\012 ... Dishwashers

Moffat dishwasher The door has come repositioned on the left side and it will not shut properly and when the door is all the wway open, the bottom rack will not pull out smoothly without lifting it up slightly. Haven't tried it since the problem arose as I was afraid that it would leek. also I didn't want to force it back into position for fear that I ould break it. I bought it Aug., 2006. It is a Moffat Model #MHDD210LOOWW.


... Dishwashers

Pump problems we have a mobile car wash service that we use in the winter months we have a 300 gal tank and several power washers.we use 3 diffrent machines [email protected] gal 2500 [email protected] and a3000psi @3.0 gal i;m having a lot of pump problems with all of these machines.a friend that he thinks that the hose that the machines feed of is to small 3/4'' he suggests i use a1 1/2 hose as close to the machine before adapting to the 3/4'' fitting right now it;s about12'' long away from the tank.any info wo


Are you only using gravity to feed the machines. The law of gravity is that, for every foot of elevation you will get 2 PSI ( pounds per square inch) of pressure. You can figure out the minimum volume that the manufacture requires and make sure that ... Comet GXD2527G Pressure Washer Pump

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

I have a hotpoint aquarius DF22, problem: machine not taking in water to commence the cycle, (this is intermittent and worked sometimes) the plumbing has been checked regularly and for a time would start after reconnection, the motor is fine the electrics have been checked by a qualified electrican who cannont source the problem, now the machine will not take in water at all, any suggestions please?


... Dishwashers

Dishwasher Problem... Hey, I'm sorry I can't seem to find this information anywhere else. I'm having a similar problem with my dishwasher (also a kenmore quiet guard) and I wanted to try to clean the filter. I'm not sure how to remove the lower arm of the dishwasher. There is a kind of plastic-screw in the middle of the lower arm, is that what holds it on? I'm afraid to try twisting it because I don't want to break it. How did you get it off of yours? I hope I'm not bothering you! Thank you, Je


You are right. The plastic screw needs to be removed. I have a Quiet Guard 4. My procedure is as follows:\015\0121. Remove baskets. Need to pop off the 'keepers' at the ends of the top slidding shelf supports.\015\0122. Remove bott ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

I recently purchased a northstar 4000 psi pressure washer. I had the same series pressure washer for the past 6 years and used a downstream chemical unloader quick connect to pull chemical. I attached it to the pressure washer and it is not pulling. I havent modified anything and I dont want to pull chemical through my machine.


The injector might be worn out or have something inside of the valve causing it not to ****. If you are using a new high pressure hose or a longer hose this may also have an effect over the injector not working. ... Northstar Professional Series Pressure Washer 4000 PSI

I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was "I" indicated, or maybe means "1". Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling out the plug from the wall socket, and reconnecting the machine, on the display stays the indication "I" or "1". I can't do anything ...what's the problem


I do not know if you been talking to other experts but without knowing how far you went with them if any I may need to start from the beginning these units are sold in Europe and not the US is that true. Second from your post you went t ... Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Flashing light The 3rd light to the right keeps flashing. I cannot cancel the programme or move the indicator light to any other setting. When I close the door the machine does not come on, just the light keeps flashing. Any idea what the problem can be? There is no water in the machine and doesnt appear to be any blockage in the outlet pipe.


... Smeg 24 in. DWI612 Built-in Dishwasher

Dishwasher flooding Hi my Asko D1716 Super Cleaning System Dishwasher has started to have a flooding problem. When the cycle finished last night it seemed fine then in the morning the machine was full of water, I scooped out the water and by this evening the machine had flooded onto the kitchen floor. I tried other solutions I found on this website but they didn't suit my dishwasher as it doesn't have the appropriate buttons. Any suggestions would be appreciated!


When you say that you tried other solutions.. it's hard to know which you've tried and which you haven't so I will suggest some basics first.. ( if you've tried them, then disregard)...\015\012Have you checked or addressed the following:\ ... Asko D1716 Built-in Dishwasher

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

My Hotpoint FDW20 dishwasher does not heat up and is washing cold. Could you, please, suggest a solution to the problem. Can you also forward me a circuit diagram for the machine along with a manual with the location of various sensors, switches and other electrical components and the wire colouring to these components. I am an electronics engineer by profession so if had a circuit diagram and a legend of the various sensors and switches along with their location on the machine it should be pos


Hi,Check your heating element.. \015\012A bad heating element causes many problems in dishwashers...Dishwasher Problems The Heating Element n ... Hotpoint Dishwashers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

Same problem! Did you ever get your machine fixed? If so, do you have any suggestions? I am encountering the same problems. thanks, Gigi


Yesn i did fix my dishwasher my self it was the thermal fuse it cost 27.95 at the local appliance store easy fix front panle comes off you cut the old one out but be sure to turn off electric crimp the new one on does not matter which wire you hook u ... Dishwashers

Maytag MDB6000AWB runs good. Steam coming out from under counter in back of machine. Machine is installed in a peninsula. Can't find a break in supply line. no evidence of water when unit was pulled out to look for water leaks.


Called repair man ... Dishwashers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

I have an LG Dishwasher model LDF9810ST. Error code E1 keeps showing (Water Leakage Problem) NO water problems anywhere to be found. I have a hard time shutting down the machine. It has had a new MAIN BOARD, and a NEW MOTOR. This unit is not 1 year old yet. Any suggestions?


Are you draining the unit in the basement or under the kitchen sink?\015\012\015\012If you are draining the unit to the floor you will need a new drain hose with a syphon breaker. This drain hose is factory installed on all new LG dishwas ... LG LDF9810ST Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1502 seconds