Having problems with your Hotpoint 23 in. BFI62 Built-in Dishwasher ?

Cycles are off

\015 Somehow the knob that you turn to the cycles is messed up. The cycle does not start at start, rather somewhere closer to rinse. The soap container won't lock until the knob is somewhere half way pointing down, etc.\015

Answers :

If you can pull knob off make sure shaft is not cracked inside if thats alright take screws out of dishwasher down the sides and around console to access timer make sure timer mounts are not broken
Repair Help & Product Troubleshooting for Hotpoint 23 in. BFI62 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

First we had drain issue with Bosch Integra® 500 SHX55M05UC Built-in Dishwasher ECO cycle. It stopped after a while. I thought it may be because last cycle might not be finished well. When we ran again ECO cycle with no drain issues but cycle did not finished as it used to be. I am sure because cycle countdown were not zero and because infra red light was off which is sing of complete cycle.


... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

Dishlex dx303wk heating the water to luke warm on normal cycle but heats ok on intensive cycle. Also not heating on rinse cycle. Also no heating on the drying cycle


... Dishwashers

FDW60 Error code 3&4 . After reset m/c drains on all cycles. Start new cycle, m/c fills but then cycle stops. Makes bubbling noise and appears to overheat. Fault is same on all cycles. M/C drains on all cycles following reset.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

I have a Whirlpool model #GU2548XTPQ3 that flashes the glass express cycle when not in use and when using the cycle switches from the cycle that was set to the glass express cycle. The unit will not allow you to cancel the setting and restart. I have to unplug it after each use, until today in which I was unable to use at all because it will not clear the glass express cycle.


I don't know if this will work but it is worth a shot. Try to reset your dishwasher by pushing the buttons in a sequence. Usually it is Heated Dry, then Normal, then Heated Dry again and then Normal again - all in a row, don't pause, but do it in a f ... Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

I have a frigidaire dishwasher model # PLD2850RDC0, it will not change cycles from the lower rack wash cycle. It will not turn off or change to any other cycle. When I take power from it and reconnect it will let me change cycles at first, a sensor light on the control panel lights then it changes to the lower rack cycle by itself and we repeat it all over again.


... Frigidaire Dishwashers

Am15 dishwasher problem: The pad will only turn on and off. Can't get it to cycle. Was on cycle 4 needed cycle 1. Got it to cycle 1, but now on and cycle does not work and when I push the off button it reboots to on. I put new pad on thinking it was the pad but same problem. Question: Is there a way to reset the board? should I be looking some where else? I cut the power at the breaker box to see if that might reset with no luck.


... Hobart AM15-2 Dishwasher

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

ARISTON LSI 45/50 UK ALL COLD CYCLES ARE PERFECT ON HOT CYCLES IT GOES THROUGH ALL THE STAGES BUT NEVER ENDS THE CYCLES AND ALSO I THINK THE ELEMENT TEMPERATURE IS NOT BEING SENSED TO ALLOW HOT WASHES TO CONTINUE AND FINISH I ALREADY REPAIRED THE INITIAL FAULT WHICH WAS A RED 2 PIN CONNECTOR WITH A WHITE SOCKET GOING IN TO IT BOTH WITH 2 RED WIRES ON WHICH WAS VERY BADLY BURNED / CORRODED I REPLACED THIS WITH A 15 AMP CONNECTOR BLOCK BUT NOW I HAVE THE HOT WATER CYCLE FAULT


I tried to look up your model dishwasher ( aristion lsi 24/50uk ) by whirplool / can not find in data base / also you stated that all cold cycles work/ most d/w only use hot and there is no cold cycles . so there is always time to ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher is starting it's cycle, then running for a minute or 2, then it stops and drains itself, then starts the cycle over and repeats this. It won't continue it's cycle and it seems to be stuck in a certian cycle


You seem to be stuck in a 'quick rinse' cycle. double check your buttons as well as your timer/dial to see if you are using the normal wash cycle. especially check the buttons. good luck ... Frigidaire Dishwashers

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0946 seconds