Having problems with your Hotpoint 23 in. BFI68 Built-in Dishwasher ?

Function buttons do not work on off button does

\015 Hotpoint dishwasher bfi 680\015

Answers :

I have expreienced the same problem and carried out a hard re-set by holding down the on/off switch whilst pressing the program button. It's now working - but not sure for how long!
Repair Help & Product Troubleshooting for Hotpoint 23 in. BFI68 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

MDB9600 buttons function erratically and the display is not working Heavy wash button will not function at all.


DSX-1 interface. Pinouts for each of the RJ-48C jacks are RCV to the DSX-1 from the span on pins 1 and 2, .... DSX-1 Drop. RJ-48 C, terminal blocks. Power Supply Options ... HiGAINMINI SHELF. INPUT: WITH PS 100/1 ... Dishwashers

I have a Maytag quiet series 200, it been working fine since I purchased it last year, as of today I pressed start and it won't start and yet when I press the delay buttons of 2, 4, 6 it lights up and so do the other functions but to change my settings that doesn't work neither as well as my start button. Whats wrong with it? Any ideas? My model # is NY2222514


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Kenmore Dishwasher model # 665.16602300 Control panel push buttons do not function except cancel and delay buttons. No other buttons work at all. Thanks for help in advance Rich Bussmann


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

KitchenAid dishwasher, KUDE40FXSS, stopped functioning, buttons do not seem to work, when you close the unit keeps beeping


... KitchenAid KUDE40FXSS Builtin Dishwasher

Wash buttons don't work. 3 second light is on, flashes when other function buttons are pushed.


... Maytag 24 in. MDB8750A Jetclean II Built-in Dishwasher

My Maytag mdb5130aww dishwasher stopped working; the only function it does is DRAIN. The panel buttons light up. WASH, RINSE etc all do not work. How do I test if the control panel is sending out power to the water pump? What else can I check?


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I have a Maytag dishwasher model MDBTT60AWW. None of its wash modes will work when pressing their respective buttons. The Fields Service Test functioned normally with the exception of the "heated dry" and "sanitize" LEDs not being lit. Tried to perform the Manual Function Test, but none of the components would operate upon pressing the respective keys for testing their operation.


Hi, \015\012Sounds like either the control board or the keypad.Try removing power from the unit to see if it will reset.\015\012Now try running the diagnostics…RIBBON CABLE CLEANING ... Maytag 24 in. MDBH955AW Built-in Dishwasher

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

I have a MDB5130AWW model dishwasher and it has worked extremely well up until a week ago. Now there is water sitting at the bottom of the dishwasher, and the "Clean" and "Rinse Only" buttons are blinking. I've read the manual, and ran the Automatic Function test, and it seems that these two buttons blinking indicates a Motor problem, specifically a low current problem. Please Help!


You may have a seized/stuck motor. Turn the electricity off and remove the lower panels. Take a flat head screw driver and carefully attempt to move the motor impellers. If the impellers feel hard to turn continue to try and free the impellers. I ... Maytag Dishwashers

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

BOSH DISHWASHER SHU5300: DOESN'T DRAIN COMPLETELY, WATER DOES NOT SIT ON THE BOTTOM BUT POOLS UNDER THE FINE FILTER. THE WATER HAS A BUILD UP AND THEN BEGINS TO SMELL. UCK!! I HAVE DONE ALL OF THE CARE & CLEANING POINTS FROM THE MANUAL. THE DRAIN HOSE DOES NOT HAVE AIR GAPS, THAT ISSUES WAS ADDRESSED. PLUS SEVERAL OF THE BUTTONS DO NOT WORK. THE BUTTONS DEPRESS BUT DO NOT FUNCTION. BEGINNING TO QUESTION IF I SHOULD REPLACE THE DISHWASHER? (10 YEARS OLD) THANKS FOR YOUR HELP!


Def replace .....time to put the old girl down ....whirlpool is a good choice ....or another bosh ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a Kenmore elite 13102 dishwasher touchpad that has begun to crack around the start button. Does this necessitate changing out the whole electronic control pad or is there a part that is the "overlay" to the control panel? The functions for each button on the panel work fine. LH


Hello,You will need to replace the touch pad assembly. You can purchase the part from the link below. ... Dishwashers

Function buttons do not work on off button does


I have expreienced the same problem and carried out a hard re-set by holding down the on/off switch whilst pressing the program button. It's now working - but not sure for how long! ... Hotpoint 23 in. BFI68 Built-in Dishwasher

Greetings. I have a Fisher & Paykel dishdrawer - the top drawer appears to have lost power mid cycle and the lid has not retracted - no led display - no response from the buttons. The bottom drawer functions ok. I have tried turning the power off at the wall for 30 seconds and on again. I have tried swapping the top and bottom controllers and the bottom still works but the top does not, so the controllers must be ok Not sure where to find the model number sorry. Any suggestions?


Describethe inside of unit,any wear on it anywhere, the rack the dishes go on is it plastic coated? is it wore with rust comeing though on tips here and there? ... Fisher and Paykel DishDrawer DS605FDSM Stainless Steel 23 in Builtin Dishwasher

Hi, I have an Electrolux ESL 4115. It seems to be stuck on 50 degrees but wont start as usual when I close the door, the on/off button works and lights functioning as normal but that's all. Thanks


I had a similar problem - seemingly stuck or locked with a solid light showing (in my case on the 65 degree wash). Nothing seemed to unlock it. But when I closed it and went away to think about what to do next - some 5 minutes later - it made its e ... Electrolux 24 in. ESI6220X Free-standing Dishwasher

Bosh Diswasher SHU3326UC/U12 Diswasher pump is stuck at drain, motor running non-stop. Control cycle button not functionning, only the ON/OFF. What can I do? I try to put circuit breaker OFF and ON to do a reset. It didn't work


Dry out the catch pan under the dishwasher. Unplug the unit for 45 min. Repair man said this should reset the unit. ... Bosch Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Kenmore Elite Dishwasher- The touchpad (control panel) keeps going ot and stops functioning. The control board is fine but the start button on the touchpad stops working. If I press it multiple times over and over it will finally engage and kick on. This is my second control panel, can the switch membranes be cleaned somehow?


Jodahabo,\015\012\015\012can you post the rest sequence? i would love to try this!\015\012\015\012thanks,\015\012\015\012the_strum_one ... Dishwashers

Whirlpool GU1500 dishwasher - no wash cycle buttons would turn on (no indicator light/no operation), but the Cancel button/2 minute drain function works. Any suggestions?


I had the same issue. If you have a 1100,1200,1500 etc you have the first series of the dishwasher and there is a heat sensor issue. The dishwasher runs and checks if the water heats up by 8 degrees. If the water doesn't heat enough then the washe ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1062 seconds