Having problems with your Hotpoint 24 in. DF55 Free-standing Dishwasher ?

Water fill problem on Hotpoint Dish Washer Deluxe Model DF 31

\015 \015\012Hotpoint Dish Washer Deluxe Model DF 31 \015\012 \015\012Problem started with water inlet safety valve not letting enough water into machine, I tested coil on solenoid and found it open circuit. Coil changed, however, after changing coil only limited amount of water if any now entering machine and machine waiting for sufficient water to start washing cycle.\015\012 \015\012After fitting new coil to the machine it did run through washing cycle but took along time to fill and rinse, now it appears insufficient water is entering machine. I have tried the solenoid on a test lead with the water connected and solenoid works however solenoid dose pass water but not with any force. There is a small black pipe also connected to the solenoid housing looks like so kind of bellows / pressure switch not sure what this dose or if it can be part of the problem?\015\012 \015\012Any help would be most welcome\015\012 \015\012Regards\015\012 \015\012Brian \015

Answers :

Pl check the small filter fitted near the water inlet hose. Probably you may have to pull this filter as this is housed in the threaded pipe attached to the body.

Remove the hose from the machine and try flushing. see whether you get sufficinet pressure from over-head tank!

Clean the filter with tooth brush or reverse clean. Do no for get to fit rubber washer.
Repair Help & Product Troubleshooting for Hotpoint 24 in. DF55 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water fill problem on Hotpoint Dish Washer Deluxe Model DF 31


Pl check the small filter fitted near the water inlet hose. Probably you may have to pull this filter as this is housed in the threaded pipe attached to the body.Remove the hose from the machine and try flushing. see whether you get suffi ... Hotpoint 24 in. DF55 Free-standing Dishwasher

Hi, I have a Miele G681 dish washer with an intake/drain light problem. I've read all posts about similar problems I could find both on this forum and others but I'm afraid I still can't figure my problem out. The intake/drain light starts blinking mid way into the dishwashing process. The dish washer fills up, rinses, drains, water is hot, everything seems to function just fine. Some time after the tablet drops from its door mounted container, and the time estimate reaches 46 minutes r


... Dishwashers

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Dishwasher does not fill with water when started. Problem began slowly with dishes not rinsing completely. Overfill float appears to work properly. Water fills pipe leading to fill solenoid but does n


I am almost certain that your problem is the fill solenoid.If it does not work, there will be no water entering your machine.I would either remove it and test it or just replace it at this point.Tim ... Dishwashers

I have a Tappen whisper quiet dish washer model number 61-1160-10. My problem is that 2-3 hours after use the tub fills up with water and leaks all over floor. there is what looks like a "D" shaped vent or something on the left side of tub about 1/2 way down appears ther is a trickle of water comming out of this.


Ok here's what the problem could be. Under the dishwasher there is a water valve the is where the water line connects to the dishwasher, This may possibly be a blue valve. From the sound of your problem the valve is not quite shutting off possibly ... Dishwashers

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

Samsung 9E Error - Low Water Level. Dishwasher has worked fine (10 months old). Confirmed adequate water supply/availability. When opening the dish washer after error, the inside has no standing water. I can hear the dish washer initially fill. This happens later in the cycle (maybe 10 mins in) Should I replace the fill switch/sensor. Is there any info available on how to fix it my self. Appreciate your help!


... Dishwashers

DIPLOMAT DISHWASHER FILLS AND EMPTIES WITH NO PROBLEM BUT.... THE WASHER ARMS WILL NOT TURN AS NO WATER IS GETTING TO THE ARMS TO WASH THE DISHES ANDBODY GIVE ME ANY HELP PLEASE


If there is not enough water, the dishes would not get cleaned. This \015\012\011\011\011could be caused by a partially closed water shut-off valve (located \015\012\011\011\011under the sink), or a faulty dishwasher water valve (located at the \015\ ... Dishwashers

Hello, I have a Maytag Stainless Steel MDBH975AWS dish washer. After water fill, it is very noisy almost like a grinding sound. Is there a common problem? Is there an exploded parts view somewhere so I can disassemble the grinder portion to see if there is a loose part?


Impeller is jammed onto shaft ,remove motor with 1 bolt ,remove impeller by putting a plastic pen in bottom of motor turn impeller counterclockwise inspect for clearance or obstruction.either replace impeller or do like I did and put a spacer,poor de ... Maytag Dishwashers

I have a hotpoint built in automatic dishwasher model HDA3740G02SA. When my dishwasher runs all the cups on the top shelf seem to have dishwashing soap powder left in the bottom of the cups. I do not over fill the cup where you put the dish washer powder in. It seems like it isn't rinsing the glasses and cups on the top rack of the dishwasher properly. Do you know what the problem would be and how to correct it?


Make sure the arm on top isnt hitting something, each time you load it each in there and spin it to be sure it moves freely, also make sure your rinse agent container is full of rinse agent. ... Hotpoint 24 in. HDA3740G Built-in Dishwasher

MY HOTPOINT DISH WASHER MOD #HDA2000G00WW WILL FILL WITH WATER AND THEN JUST PUMP IT OUT.


... Hotpoint 24 in. HDA2000Z Built-in Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Hi my L G dish washer is coming up with E1 . It comes on after about 2 min it takes water into the washer then it hummes for about 30 seconds then comes up with E1 and pumps water back out. I have checked the hoses which don't appear to be leaking -I read somewhere in your answers about this problem that it could be the Water Level in Drum lowering, this means there is a leak on one of the pipes. More likely it is the Circulation Pump, which is responsible for pushing the water to the Spray


Hello aderry -\015\012\015\012\015\012I'm a bit short of time as I'm on my way out to a service call, but I've uploaded the service manual to Rapidshare for you to download. \015\012\015\012\015\012Rapidshare download inst ... LG Dishwashers

Dish washer won't fill with water


... De Dietrich 18 in. VZ9456 Built-In Dishwasher

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Hello, Welcome to FixYa.I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

NOT ENOUGH WATER FILLING UP IN WASHER. EVERYTHING ELSE WORKING BUT DISHES NOT GETTING CLEAN AS NOT ENOUGH WATER RELEASED INTO WASHER AT START. WHEN I ADD TO POTS OF WATER IN THEN WORKS FINE??


The presostat or whater level sensor is not good ... Dishwashers

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

Dish washer not filling with water when put on


There are a few things that can cause this problem, it could be a defective water inlet valve, it's usually located behind the lower kick plate on the left or right hand side of the dishwasher, When the washing cycle is started it sends voltage to th ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1945 seconds