Having problems with your Hotpoint 24 in. DWF32P Free-standing Dishwasher ?

Hole in pipe at bottom of dishwasheris this a water pipe or heat

\015 Hole in pipe at bootom of dishwasher\015

Answers :

Replace it., but I suppose you figured that....
Repair Help & Product Troubleshooting for Hotpoint 24 in. DWF32P Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hole in pipe at bottom of dishwasheris this a water pipe or heat


Replace it., but I suppose you figured that.... ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

Hi, I have a Kenmore 15879 that is basically working except the bottom water spinner...lol (don't know technical name). The dishwasher pumps the water into the bottom of the dishwasher, will heat the water, but not disperse the water in the spinning sprinkler manner it's suposed to. I've opened the dishwasher in time to see that water is spurting out of the holes about 2" high, but it's just not spinning. The water also drains just fine after the whole cycle.


This is caused by the impeller being clogged or the pump is failing, When the pump is woring properly the water will shoot out with force. ... Kenmore 15879 Built-in Dishwasher

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

GE PDW8280 - MIDDLE ARM WILL NOT SPIN - WATER FLOWS AND SPINS FROM TOP AND BOTTOM ARMS - MIDDLE ARM HAS WATER FLOWING BUT WILL NOT SPIN. tOOK APART AND CLEANED - SPINS FREELY BY HAND BUT NOT DURING CYCLE. SUSPECT LOW WATER LEVEL? WATER IS ONLY UP TO BOTTOM OF HEATING ELEMENT


Take the whole middle spray arm assembly off -- spray arm and long tube that it is attached to. I cleaned the inside of the spray arm and found some odd stuff but it still didn't swing after the cleaning. I order all new parts and when I was repl ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

I have a Zanussi dishwasher model DA 6141. For some time now it has not been completely discharging the water at the end of a cycle. But sometime it does completely dicharge.Two days ago it started leaking water from its bottom at the end of a cycle.I tried to locate the leak but was unsucessfuly. All the external plumbing is ok andf there is no leak from the discharge pipe nor water intake pipe. So perhaps its something to do with the water pump?


Hello David,\015\012\015\012Have you removed and cleaned both filters and checked they are inserted correctly? I've uploaded the filter cleaning instructions to Flickr for you:\015\012\015\012 ... Zanussi Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

I have model KUDV24seal5. It leaves a film on the glasses, and they don't look clean. The water in the bottom after running it is also cloudy. I run the rinse cycle before loading and put vinegar in the water that helps a little. I've cleaned the bottom and the arm and the pipe the water goes up to the top level. Is my pump going out?


... KitchenAid 34 in. KUDV24SE Built-in Dishwasher

The water didn't drain . I washed a broiler pan and used pot scrubber and heated dry. I opened the dishwasher during heated dry and greasy water is still in the bottom of the dishwasher. Could it be a grease clog?


Yes take a smaller hose and put through the drain hose then push drain/cancle ... Hotpoint 23 in. BFI62 Built-in Dishwasher

I have a baumatic mini4 tabletop dishwasher and when i put it on to start a cycle after 2 mins water starts pouring out the bottom of the door and floods my kitchen? i have checked pipes and they are ok and when i switch the dishwasher off and back on again the water drains out the bottom of the dishwasher ok.


Hi,\015\012\015\012As there are a couple of troubleshooting for this leak. As with out doing it is not easy to understand whether its a plumbing issue or the washer is not draining constantly in cycles.\015\012\015\012 ... Baumatic 18 in. BFD46 Free-standing Dishwasher

Small Burn spots on interior tub below heating element. These spots have small cracks in center of them, and leak right through the bottom of the tub, dripping water all over under the dishwasher. Nothing has falling into the bottom of the tub, and nothing has touched the heating element. What in the world could be causing this to happen? Kenmore Ultra Wash Quiet Guard 4 Mod.# 665.1603* Purchased new from Sears 2006


Hi,\015\012\015\012The heat from the element when the dishwasher is in the "drying" mode has caused the bottom to stress crack and become open so it leaks...\015\012Ultimately this will cause you to have to replace the dishwasher... ... Kenmore Dishwashers

20 year old Maytag jetclean model WU482 small hole in front bottom of tub leaks water


... Dishwashers

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

I have a Kenmore Ultra Dishwasher. The bottom arm spins, the top doesn't, although water drips out. The water fills up under the heating element. The top dishes aren't getting clean and the bottom aren't as clean as they used to be. I also noticed that the soap dispenser is open, some of the soap is gone, but there's still some soap in left in the dispenser. This never happened before and it happens all the time now. Thanks for any help you can give me!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1452 seconds