Having problems with your Hotpoint 24 in. FDW60 Free-standing Dishwasher ?

SDW60 - AL08 Error - No Hot Water

\015 The delicate LED flashes fast at the end of the cycle. I am guessing it is at the end of the wash cycle, because the dishwasher doesn't look like it has gone through the rinse/dry cycles. The dishwasher is cold when opened, so the water isn't heating up. Has anyone got any ideas why this is happening?\015

Answers :

First switch off the machine and unplug it at the mains. Leave for 10 minutes then plug back in and re set your machine to the programme you want. It might be that the control panel needs re-booting. They are a bit sensitive and mine had a mind of its own, washed to its own agenda, left water in the bottom etc etc. so that might be the problem with yours. If that doesnt do it, go on the Hotpoint website and find the customer service number. Ask if there is anything you can do to solve the problem yourself before paying for a service call. It could be your heating element has packed up but try the easy fix first. Thats what I did and it cost just the price of a phone call. They were really helpful.
Dwf 70 al08 water not heating. heater element ok and relay on pcb is ok (tested by removing)
Repair Help & Product Troubleshooting for Hotpoint 24 in. FDW60 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SDW60 - AL08 Error - No Hot Water


Hi fridge-1,\015\012I had the same problem and fixed it by fitting a new control board .\015\012Best of luck.\015\012michael-howe ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

SDW60 - AL08 Error - No Hot Water


First switch off the machine and unplug it at the mains. Leave for 10 minutes then plug back in and re set your machine to the programme you want. It might be that the control panel needs re-booting. They are a bit sensitive and mine had a mind of ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

F4 error - machine gets stuck on a particular time half way through and cycles till it eventually throws an f4 error. When opened- steaming hot, soap tray unopened, undrained water in bottom


Hi,F4 indicates that there has been no temperature increase detected for 2 hours while the element is on. Possible causes are,The element is not connected, broken wires.The element has failed in an open ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

My hotpoint dishwasher SDW80 is flashing error code AL80 and has no hot water can anyone help me with this please.


... Hotpoint Dishwashers

Zanussi zdt 6764 built-in dishwasher. no hot water and no heat during drying, the machine goes through it's whole cycle with no error codes visible . I have already changed the element , what'


... Zanussi Dishwashers

My LG dishwasher is stopping after a few minutes into the wash cycle with an error message OE and making a sound. The dishwasher tablet is still inside the dispenser and while there is water in the unit it isn't hot. Any ideas what is wrong, I don't have a manual


Hi rebeccasolom,OE means "Outlet Error"The drain pump is either clogged or the outlet hose is kinked.- Inspect the Drainage hose at the back for kinks.- Open the unit, and at the bottom sump check the small drain p ... LG 24 in. LD-12BW5 Free-standing Dishwasher

I have an E1 error code coming up on new omega dishwasher. Model ODW707WB/ODW707XB. Have just installed today and have hooked it up to the hot water pipe. What should I do to fix please.


... Dishwashers

Installing a built-in LG dishwasher; got everything ready to go, but a problem with the hot water line coming in. It is barely long enough to reach to the front where I've installed the elbow. Since I have to back the dishwasher in to the 24 in. hole there is no room for error in terms of not running over this hose with the bottom of the dishwasher. Any tricks to handling this situation?


Hi, best way would be to install a "spring" attached to the back of the dishwasher. The hose would connect to that and easily "pull-away" when moving or "pull-tight" taking up the slack. A much simpler method is to tie a piece of string to the hot wa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

There are no error codes showing, water is definately getting hot but dishes on bottom tray not cleaning, i have used few products specially designed to clean the dishwasher itself without any dishes in, checked the filter, salt, etc, used tablets, gels ... nothing seems to work. Dishes just not clean !


Lower washer not working but upper washer is. This is due to the dishwasher thinking it is on half load. the sensor is faulty and you need to replace the whole unit (water circulation pump). However if like me and your not bothered about having a hal ... Baumatic 23 in. BDW13 Built-in Dishwasher

ERROR CODE : THEMISTOR PROBLEM OR WATER TEMP TOO HOT


The thermistor is located in the sump assembly next to the heater element.  The only way to get to it is to remove the dishwasher, turn it on it's side, remove the bottom panel to gain access to it.  Before you do that, remove the front doo ... LG 24 in. LDS 5811 Built-in Dishwasher

Got a Diplomat ADP8322. Starts Cycle then starts bleeping 3 flashes which is a heating error. No hot water at all. Had a look and cleaned watr pressure switch still not working. Any ideas has the heating element gone.


Possibly heating element - only way to find out is to check continuity with a multimeter.there is also a thermal cutout in series with the heater which could also have gone ... Dishwashers

All of a sudden the dishwasher water is not hot (usually the water is very hot when wash the dishes ).... even when I put the hot water sink tap running out hot water... then start the dishwasher. the rinse cycle only warm water ... usually the water is steaming hot and drying cycle the dishes are too hot to touch ....


Check the heater. Heater control circuit. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

I have purchased a Bosch dishwasher SMS50E22au. The manual instructions say cold water connection only yet there is also instructions for a hot water connection . We have solar hot water, and we are unclear as to whether we can connect to solar hot water.


... Bosch SMS69L 24 in. Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

The first cycle does not have hot water - the sink right next to it has hot water - the other cycles have hot water???


Most\015\012washing machine timers are digital or mechanical. The timer controls\015\012most of the operations of the washer: water level, tub filling and\015\012emptying, length of cycles, and cycle setting sequences. For this\015\012reason, a ... Maytag 24 in. DWU7402 Built-in Dishwasher

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own wat ... Bosch SHX46A07UC Built-in Dishwasher

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1354 seconds