Having problems with your Hotpoint 24 in. FDW60 Free-standing Dishwasher ?

Hotpoint FDW80( A10 Appears ondisplay half way through cycle)

\015 Got a hotpoint fdw 80, it gets halfway through a cycle then A10 appears on the screen, Any ideas how to fix this problem?\015

Answers :

Here are the fault codes for your machine...

\015\012Fault codes for LCD Dishwasher Models\015\012 \015\012
  • A01 - Float switch operated - Book a service engineer.
  • \015\012 \015\012
  • A02 - Open/Short circuit heater relay - Book a service engineer.
  • \015\012 \015\012
  • A03 - Short circuit on thermistor - Book a service engineer.
  • \015\012 \015\012
  • A04 - Unable to reach or sense temperature within 70 minutes - Book service engineer.
  • \015\012 \015\012
  • A05 - Pressure switch has not been reset - Book a service engineer.
  • \015\012 \015\012
  • A07 - Open/Short circuit wash motor triac - Book a service engineer.
  • \015\012 \015\012
  • A08 - Open/Short circuit auxiliary wash motor triac - Book a service engineer.
  • \015\012 \015\012
  • A09 - Open/Short circuit with main wash traic - Book a service engineer.
  • \015\012 \015\012
  • A10 - Open/Short circuit fill valve traic - Book a service engineer.
  • \015\012 \015\012
  • A11 - Half load valve traic or alternating motor action - Book a service engineer.
  • \015\012 \015\012
  • A12 - Open circuit heater rely - Book a service engineer.
  • \015\012 \015\012
  • A13 - Open/Short circuit dispenser traic - Book a service engineer.
  • \015\012 \015\012
  • A14 - Drain hose too low causing syphoning. Check drain hose and re-adjust.
  • \015\012 \015\012
  • H20 - Check tap and pressure of incoming water


  • Hope this helps?
    I had the same fault. After searching for advice from various websites I tried using cheaper tablets and filling the salt dispenser. Instead of using the latest Finnish tablets I changed to Daisies from Tesco. Have since completed over 80 washes without the problem recurring.
    Repair Help & Product Troubleshooting for Hotpoint 24 in. FDW60 Free-standing Dishwasher

    Tips for a great answer:

    - Provide details, support with references or personal experience .
    - If you need clarification, ask it in the comment box .
    - It's 100% free, no registration required.

    Suggested Questions/Answers :

    Hotpoint FDW80( A10 Appears ondisplay half way through cycle)


    Here are the fault codes for your machine...\015\012Fault codes for LCD Dishwasher Models\015\012 \015\012A01 - Float switch operated - Book a service engineer. \015\012 ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

    We have a hotpoint aqaurius dishwasher df23n. When put on wash 4, the timer stops half way through and has to be helped. When the programme then continues through the rinse cycle, it stops half way through. I have tested the water heater and thermostat electrically and they seem ok. Is there anyting else that stops the timer at these positions? The timer knob is free to turn and is not jamming? Steve B


    ... Hotpoint Dishwashers

    AEG Favorit 350 dishwasher starts cycle okay but starts beeping about half way through and although dishes appear clean there is dirty water lying at bottom of dishwasher so not draining away and the drying cycle has not started.


    ... AEG 23 in. Favorit 88070IM Built-in Dishwasher

    I have a Kitchenaid KUDK03CTSS2. It goes about half way through the entire cycle, let's say half hour in and then it sits there buzzing/droning for at least 30-40 minutes, then it finishes fine. Had a service guy in and he would't wait for the symptoms to appear. Everything is good at the beginning. He replaced the pump motor, didn't find any debris in the unit. But it's still doing the same thing.


    Turn the dishwasher off about 20 minutes after it starts the droning/ buzzing and feel the water temperature.\015\012\015\012Also run the dishwasher in a short cycle where it uses cold water only and see if there is any difference.\ ... KitchenAid Dishwashers

    We have a Hotpoint DWF31 dishwasher which seems to have a fault in the programmer. On 'Normal (65) and Economy (50)' the minutes to end comes up as '2H' and although I have set it running on both programmes, it doesn't appear to be counting down or performing the normal cycle. On the other programmes it works normally. According to the User instruction book, the programmer is self learning and calculates the minutes to end based on previous use of that programme. Is there any way of resetting th


    Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. Switch off the\015\012dishwasher from the power socket and mains and replace all the cables and\015\012switch it on after five minutes. Yo ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

    I have a Kenwood KDW243A model dishwasher, and half way through programme the bleeper goes off and E4 code appears in the display window. There is nothing in the Instruction Manual which explains this. What is going wrong? The cycle moves on but the dishes are not drying and are greasy.


    Hi,\015\012The E4 error means that the flood sensor is\015\012detecting water in the base pan. Pull the unit out and tip it backwards\015\012for 30 minutes to drain the water out. and reset the flood sensor.\015\012After 30 minutes tip it ... Dishwashers

    Hello My zanussi diva edw1500 stopped working half way through a wash and there is i30 flashing. According to the manual this is some protection against flooding. I thought it was my external drain was blocked and this was stopping the water from being pumped out of the machine. The drains have now been unblocked but when I tried to resume the dishwasher cycle ther same error appears. Please can you advise? Many thanks. Kind regards Jo


    ... Zanussi Dishwashers

    I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


    ... Kenwood Dishwashers

    My dishwasher will start any cycle then half way


    The touch pad has gone bad. Common problem with the GE made dishwashers. ... Dishwashers

    Hi. we have W'house 905 dishwasher. Have had the element replaced. It gets to half way thru cycle then cutes out. Cuts off all electricity in the house. Restart again gets to half way then cuts electricity trip switch. Is ther an answer? Tks.


    \015\012Hi\015\012\015\012\015\012This is happening due to shorted wires or worn out wires connected to the element. It may also occur if you are not using the model specific part as replacement. Please get ... Dishwashers

    Hotpoint, intergrated dishwasher BF12/47916/7 has stopped working, There is nothing happening at all. it has done half a cycle the only thing that happens is when you put the cycle on the dot before cycle no: 2 the power light comes on orange, this usually goes red when the cycle is on. I have changed the fuse & there is no difference. Help!


    ... Hotpoint 23 in. BF41 Built-in Dishwasher

    Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle takes over three hours. When the cycle finally finishes the dishes are not completely dry. Is there a way to adjust the timing for the cycles? I have checked the screens and they were clear.


    \015\012There are no adjustments for cycle timing. What does affect timing is temperature of the water coming into the DW. The hotter your supply water, the shorter the time to cycle, BUT if your water is too hot, the cycle time may become too ... Bosch 24 in. SHU43 Built-in Dishwasher

    Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


    If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

    We have a Frigidaire Gallery Series dishwasher we just purchased in August. Model #GLD2445RFB2. We are experiencing a problem with it. We noticed it started running louder then normal and now it will not finish a wash cycle. It gets half way through and PF lights up on the display and the cycle never finishes. It doesn't matter which cycle we choose it has done it on all of them.


    ... Frigidaire Dishwashers

    Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


    Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

    Dishwasher keeps stopping half way through cycle have to switcxh off and put back on several times hydrapulse dishlex


    ... Dishwashers

    Stops working half way through a cycle and alarm goes off


    How many beeps does it make ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

    Frigidaire Dishwasher (GLD2250rdc6) has all lights light up through cycle and stops half way through


    ... Dishwashers

    I have an older GE dishwasher, model GSD1200T02. I recently put in the wrong soap, so I had to press the clear/reset button. When I did this, the dishwasher ignored me and seemed to continue through the cycles anyway. When it got half way between "drying" and "off", it stopped, and has been that way for several days now. It will not respond to any button pushes at all now. I cannot even reset it because it does not respond at all when I press the clear/reset button. I have had a load of di


    This is only a long shot, try turning the breaker off and on again, may be ???\015\012 Jacques. ... Dishwashers

    I have a Bosch SMU2046UC/14 dishwasher that makes some noise but will not start the wash cycle. I found that the noise was from the timer motor by removing the front of the door. The timer continues to run and but only advances until half way through the wash cycle where it stops permanently. Is this a problem with the timer or could something else be causing this problem.


    HI. The timer motor mechanism regulates the length of time power is to be routed to each component. If the timer motor does not advance properly, it can result in a wide range of problems. Common symptoms will usually include sticking in a cycle(fail ... Bosch 24 in. SMU40 Built-in Dishwasher

    My D3112 Asko dishwasher controls will not respond. There is a pump or motor running non-stop, even after I push the power off buton. The only way to make it stop is to unplug power cord. It is almost like it is stuck in the middle of a wash cycle program, but the water is not spraying inside nor is the heater or dryer cycle appear to be on.


    ... Asko D3112SS Stainless Steel Dishwasher

    Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


    This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

    Dishwasher fills and appears to be going through cleaning cycle ok. However if I open the door part way through the dishes appear as though nothing has happened, dishes are still dry and dirty. have checked hoses, manually added water, observed emptying etc. Any ideas nost welcome, Thank You


    Most of the time it's because the impeller assembly has either something stuck in it or has just plain worn out.\015\012Also you want to check and make sure the holes in the washing arms are clear (Poke a little toothpick threw the ... Bosch 22 in. SKT5108 Free-standing Dishwasher

    Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


    Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

    How do you reset the kenmore elite dishwasher? I replaced the faucet in my sink and forgot to turn on the water to the dishwasher....when I started it it went half way through the cycle when I realized there was no water. How do I reset it so that it will start at the beginning of a cycle?


    Turn off the breaker that powers it. If all else fails, take a jug, fill it in the sink and pour it into the bottom of the dishwashwer until it comes to the bottom of the heater, that's the round think suspended above the bottom, below the rack, and ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
    • Start your question with What, Why, How, When, etc. and end with a "?"
    • Be clear and specific
    • Use proper spelling and grammar
    all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
    Load time: 0.1391 seconds