Having problems with your Hotpoint 24 in. FDW60 Free-standing Dishwasher ?

I have a Hotpoint Aquarius dishwasher (FDW60) The 3hr and 12hr lights are on and the machine won't respond to any other buttons pushed therefore I have not been able to reset the machine (that is if the delay start has actually been activated). It started with the machine not draining however I was able to drain it manually so that rules out any blockages. Please help...The manual doesn't have any troubleshooting advice for those lights... Thanks


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. When 3hr (Prewash) and 12hr (drying) light flashes it indicates\015\012the fault in the heating circuit. This would be\015\012the element itself, wiring between element and control board or the control\015\012board in the door. Please do accept the solution if the issue is\015\012resolved or else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Hotpoint 24 in. FDW60 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hotpoint Aquarius dishwasher (FDW60) The 3hr and 12hr lights are on and the machine won't respond to any other buttons pushed therefore I have not been able to reset the machine (that is if the delay start has actually been activated). It started with the machine not draining however I was able to drain it manually so that rules out any blockages. Please help...The manual doesn't have any troubleshooting advice for those lights... Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. When 3hr (Prewash) and 12hr (drying) light flashes it indicates\015\012the fault in the heating ci ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

My dishwasher started making a whirring sound around 20 minutes into its cycle. I took off the drain pipe to check for obstructions, however it was clear. I started the cycle from the start again, and it started the whirring sound from the start of the cycle. There was a small amount of water that drained into the bucket where I had placed the drain hose, however there was not much water in the machine to start with (I checked when it started whirring the first time and there was no water in the


Hi.\015\012\015\012A blocked pump in absence of water won't be noisy from start. Check that\015\012 the whirring sound is not given by the spray arms. Test without baskets\015\012 and check the spray arms assembly.\015\012\015 ... Fisher and Paykel DS605I Built-in Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

We use our dishwasher daily. However, we have noticed when we have not used it over a series of days water is gathering in the bottom of the dishwasher and leaks onto the floor. We are able to drain the water by pushing the drain button on the front of the dishwasher. Any suggestions for issue/repair? The dishwasher is a Kenmore.


Hello, Welcome to FixYa ! \015\012 \015\012The problem you're experiencing based on your description sounds like (unfortunately) a common one. \015\012 \015\012The water inlet valve can be an issue with dishwasher's if they fail in the open po ... Dishwashers

Good afternoon - I have a Whirlpool model LSR7233EQ0 washer. The washer works fine in regards to draining, filling, lower agitator works...however, the top agitator does not engage and almost sounds like grinding. However (I know you are not supposed to do this), when the machine is in the wash cycle, I push sideways on the top of the agitator and it then does engage and agitate. When I release pressure, the top agitator does not work. Thanks for your help, Michael


Whirlpool uses a split agitator design. The upper portion is called the auger, while the bottom is called the agitator. Between these components is a agitator cam assembly. This problem is commonly caused by worn agitator dogs or the agitator cam ass ... Dishwashers

Our Asko D3112 was not draining, so we had maintenance drain the hoses to clear any blockage but it did nothing. They said it must be our pump not working. I ran one more cycle to see if things went back to normal, however now our pump won't shut off. We have to unplug the machine just to get the pump to stop. We had a repair technician come to look at the dishwasher and he says that it is a problem with the control panel/computer system. Something tells me it is a merely a loose wire and that w


Check your manual to see if you have a drain pan at the bottom of the unit, and a 'float' that checks for water collecting there. On at least some Asko models, water collecting in the pan causes the float to rise, which then changes the operation of ... Asko 24 in. D3112 Free-Standing Dishwasher

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers

Our dishwasher seems to be stuck in drain mode. My daughter put the wrong kind of soap in it. She accidently put Regular dish washing soap in rather than machine dish washing soap. We've got all the suds out. Seems to drain water just fine. However we cant seem to get it to add water. Does the soap have anything to do with it? Anything I can do from my end? Please Advise. Thanks


Plastic base is full of water. Need to remove whole unit to access bottom and dry it out. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

I need the steps to change the hose assembly on my Whirlpool portable dishwasher. When I got it someone had cut the sink connections off so my son connected it to the water and drain with my washing machine which was in the kitchen. However, I have moved and want to use it as portable. I purchased the new hose assembly for the sink faucet, I just need instructions on how to take the dishwasher apart and connect the new hoses.....HELP PLEASE!


... Whirlpool 24 in. Portable Dishwasher Dishwasher

I have a Kitchen Aid Superba KUDS24SEBS1. The inlet water pressure is good and the dishwasher fills and starts the wash cycle, however, after the initial spray of water, it seems that all of the water drains out and there is nothing left to continue the cycle and wash the dishes. It's like it's not able to fill up enough to wash the dishes.


When "full" of water, the normal height of level is about 1/2 below the heater assy(large blackish grey coil below he spray arm).. if theres enough water in the unit nad its still not "spraying",its quite possible that your filter/chopper assy is cl ... Dishwashers

The red intake/drain light comes on. I have removed the filter and drain however, this does not seem to make a difference. The machine works very intermittently so I am not sure what the problem is. Please help!


... Miele 24 in. Novotronic G842 Plus Built-in Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers

My Siemens SL84A305UC/21 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

My catering boss has installed a new midi 50 but the drain is to high and it won't drain. I'm I right in thinking this is a manual drain machine without a drain pump.our old machine had a drain pump. Is there any legal height that a commercial dishwasher has to be installed off the floor in regard to health and safety. thanks.


Lower height can be a violation, higher won't be. Pumps are only used to drain in a high volume environment. Many commercial clippers and washers don't have them. ... Dishwashers

My Siemens SL84A305UC/26 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

The Intake/ Drain light is on. It appears that the machine is not draining and that possibly the pump is not working properly. The drain line appears to be clear though I haven't pulled out the unit to check the drain line at the machine. Any suggestions?


... Miele Touchtronic G832SC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1165 seconds