Having problems with your Hotpoint 24 in. FDW60 Free-standing Dishwasher ?

I NEED HELP CLEANING OUT MY FILTER ON MY HOTPOINT DISHWASHER..... WHEN WE GO TO RUN IT THE WATER STAY'S IN THE BOTTOM AND WILL NOT DRAIN OUT SO PLEASE HELP ME FIX MY PROBLEM CUZ I CANNOT AFFORD RIGHT NOW SOMEONE COMING OUT TO LOOK AT IT SO IF I CAN FIX IT MYSELF THAT WOULD BE GREAT AND WITH YOUR ALL'S HELP IF YOU WILL THANKS ALICIA


Answers :

I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufacturer should have done in the factory and not made 1\015\012dollar off of this defective D/W until it proved this to be ready .What\015\012has happened to Quality Control ? Does it no longer matter ? Very sorry\015\012,you should seek a refund ASAP.
Repair Help & Product Troubleshooting for Hotpoint 24 in. FDW60 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I NEED HELP CLEANING OUT MY FILTER ON MY HOTPOINT DISHWASHER..... WHEN WE GO TO RUN IT THE WATER STAY'S IN THE BOTTOM AND WILL NOT DRAIN OUT SO PLEASE HELP ME FIX MY PROBLEM CUZ I CANNOT AFFORD RIGHT NOW SOMEONE COMING OUT TO LOOK AT IT SO IF I CAN FIX IT MYSELF THAT WOULD BE GREAT AND WITH YOUR ALL'S HELP IF YOU WILL THANKS ALICIA


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Upper spray arm and tube assembly. This part fell off the back wall. Can not figure out how to get it to stay on again. Looks like it should clip in, but nothing to snap it in place. The part does not look brocken when compared to the part would order to replace. No info in the manual and their service department was no help, How do I fix this.


Hi,\012Those p[arts wear and even though the parts do not look broken they are not up to the specs. of a new part...\012That is not that hard to fix and you can easily buy the parts yourself online... ... Bosch 23 in. SHU 8805 Built-in Dishwasher

We have a Kitchen Aid dishwasher model number KUDK03CTSS3. It's only about 3 years old, but the dishes on the top rack do not get clean. We thought maybe it was water not coming out the top, or food stuck somewhere, but do not know how to fix it. Any help would be greatly appreciated.


Had a simular problem, used product called dishwasher magic to clean it well and that took care of it. I got it @ walmart in the diswasher detergent area. Also be sure you are loading according to the manual. I now use lemi shine in every load fo ... Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

Kenmore model 16625691 ultra dishwasher I have this dishwasher and after changing another appliance in the kitchen it will not come on at all. I have looked at some of the help for the reset fix but it does not seem to work on this one. It does not have any lights at all? Thanks


... Hobart AM14-253 Free-standing Dishwasher

I have a Campbell Hausfeld Furniture Paint Sprayer - paint is coming out without me pressing the handle - continuously spraying. When I try to press there is no pressure it just flops back and forth. Can someone help as to what I need to do to fix this? Thank you


The paint is too thick try thinning out the paint would be one possibillity clogged tip/filter. Also what happens sometimes is when using latex it drys fast so sometimes it starts gumming up the springs so it doesnt allow the trigger to close up all ... Pressure Washers

I have a whirlpool dishwasher that won't start even though there is power going to it. I was told by someone at Lowes ro shut the breakers off for 15 minutes and that would no doubt fix the problem. it did not change a thing ,can you help? the model number is DU1145XTPBA the machine was purchased in 2007.


Hi,\015\012 Check there is no water in the tray under the machine.\015\012There will be a switch that turns off everything if there is a possible leak - so may be that. Just blot up any water and try again.\015\012If there is a sli ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a porter and Charles dishwasher. It comes up with two error codes. E1 and 1f. The repair person did not know why these codes meant, and is looking into it for me. Any help would be appreciated. Thanks Don


... Dishwashers

Had new kitchen so just re connected my dishwasher. Warning light to check water has come on. hoses and water going into machine seems ok but machine seems to be slow at filling. looked at filters in case of blockage with no result. Any ideas would be helpful please Merry Christmas Janice


I would remove the water line going to the dishwasher and let it run into a bucket. Sometimes on older shut off valves when you shut them off and try to turn them back on they get gunked up or dont open all the way. If you have good water pressure to ... Bosch Dishwashers

I have a Karcher B402 Pressure Washer and when i plug it in and turn it on - nothing happens, not a sound. I have checked the fuse and the plug itself and this did not help. I contacted a service technician and they said it would cost £45/hr to have a look and it probably wasn't worth fixing! Is there anything i can try to narrow down the problem/fix it myself. Any ideas what might have gone wrong? Sorry i can't give you more info. Cheers


Hi if you remove the torx screws that hold the electric box on and then bypas the on/off switch join wires together. and check the pressure swicth if it is the pressure switch you can bypass this but the machine wont shut down regards ... Karcher K2.26 Electric Power Washer

Hi I have a Siemens SE26T252GB/01 dishwasher which won't drain. (The "check water" light comes on). I have checked all the filters/drains and I think the fault is the drain pump which I would like to replace. I can remove the side panels but cannot remove the base to get access to the pump. Can someone help with instructions or a diagram please? Many thanks


... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standa ... Kenmore 24 in. 16539 Built-in Dishwasher

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Our Maytag dishwasher, mod MDB9150AWS, has abad lower rack due to rust and prongs coming loose. Maytag sent me a replacement BUT without the center spray tower. It looks like trouble to remove the old one and install it in the new lower rack. Any help would be appreciated.


Yes, I resolved the problem after thoroughly studying the assembly. It was relatively simple; all I had to do was turn the spray tower 90 degrees and it came free of the rack.\015\012\015\012Thanks for the web site, nonetheless. ... Dishwashers

I randomly have a sewer smell that comes up through the drains, sometimes in the bathroom, sometimes in the kitchen. My brother built our house and ran all the plumbing and Im wondering if he did something wrong or if it something simple to fix. Its not all the time and its not intolerable...just get a whiff of it now and then. Any advice would be helpful!


Hi, are you in a rural area, running a septic tank, by any chance?Do you have any large trees in the yard. Front, or back? ... Kitchen and Much More Dishwashers

Water is coming out of the main body of my Karcher power washer. It seems difficult to take apart but I would try it if you think I could fix it.


... Pressure Washers

Hi There I am having a problem with my Candynova CD122J Dishwasher, The problem is the water is not emptying out of it, I have checked and cleaned the filter and made sure there was not cutlery etc caught in it, Have you come across this problem before or would you have any help on this?? Any help would be well appriciated. Regards, John 00353852113372


Water pump could be out could be restriction in the hose that runs into the sink drain ... Dishwashers

LG LDS4821 Appears to be leaking from the drying vent. Not sure how to fix or if parts will be required. Looking for guidance. It happens while the dishwasher is washing. I have not attempted to fix as of yet, looking for guidace from someone who hass experienced this problem and resolved.


The leak is coming from the loose gasket in the fan assembly (blower) connected to the vent cover. What I did to fix my leak was a simple step of adding petroleum jelly (e.g., Vaseline) around the gasket holder and reuse the same gasket (clean all p ... LG LDS4821 24 in. Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Power off I have an ASKO D3100 Dishwasher, which is a few years old now. It stopped working a while ago where the power went off and stayed off (no lights anywhere). I've checked the power point and it's okay. I've flipped the dishwasher over to look inside and I can't see a fuse or anything that looks helpful. Can someone help me troubleshoot this one?


Howdy. I suspect a power surge went through your machine and fried its itsy bitsy brain.Its time for a new one unless you have a good supplier and serviceman who will replace the control unit. Get an estimate with a closed top cost before you agree. ... Asko 24 in. D3112 Free-Standing Dishwasher

I own a karcher water blaster 449M and needs an expert to solve the pomblem It does not bring out the presure required to the right job and makes a noise as well when you start it can someone please let help me in solving the delema my self or by repairing it by an expert I LIVE IN SYDNEY AUSTRALIA IN THE SUBERB ROSELANDS CAN SOMEONE LET ME KNOW OF A DEALER OR REPAIRER CLOSE BY THANK YOU FOR YUOR TIME AND HELP IN READING


Sounds as if you have a pump problem. your best bet is to go online to maker or a dealer near you for service help.you may wind up having to replace pump. ... Karcher 2500 PSI Pressure Washer

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

The door now drops hard when opening. In the past the door would drop slowly and was "not heavy" . I found a rubber piece on the floor just below the door. It looks like a rectangular washer . I am assuming the rubber piece helped slow down the drop of the door. Is this a correct assumption? Is this an easily repaired problem? Your help would be greatly appreciated


... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1419 seconds