Having problems with your Hotpoint 24 in. FDW60 Free-standing Dishwasher ?

Hotpoint LFT228A on off light flashing and error code 3 showing. Water left inside dishwasher.

\015 Is there a way of restting this washer by switching it on and off and holding the programme button. I am sure I done somthing before and it worked but cannot remember what I did last time !!!. I ahve tried draining water and checking hoses for blockages but when I run the programme it got all the way to emptying and then the error code 3 comes on and the on / off light flashes\015

Answers :

Repair Help & Product Troubleshooting for Hotpoint 24 in. FDW60 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint LFT228A on off light flashing and error code 3 showing. Water left inside dishwasher.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

The main problem is the dishwasher will not drain after the cycle indicator shows finished. There is water left in the reservoir that needs manually drained and dishes are soaked. Also, the "sanatized" light has not lit up at all. Our code is: SHE43F15UC/61 FD900700314 / SN9G5B.thanks


... Bosch SHU9915UC Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

Error Code E1 means longer inlet time. possible causes faucet is not opened, or water intake is restricted, or water pressure is too low, according to the BRADA portable dishwasher model EP9242AWW What does that mean and how do I fix it? I have shut the water faucet off and the error message still shows.


... Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

Error Code dishwasher is 14 years old, model number 47918 - error code has appeared in the LED panel inside the door but only shows the letter F, any ideas what the problem may be?


... Creda Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Caple DI604 dishwasher stops almost immediately after starting. Error code is that the 3 left lights are on when I open the door. Does anyone know what the error code means?


... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

E4 error light comes on, dishwasher won't run, this apparently means water is on a sensor, have removed water from collection tray in bottom, tilted machine backward to dry out sensor, left for 24 hours, machine still won't run. Currently a very small new counter top but a useless dishwasher.


The problem is related to the floater assembly inside the dishwasher. It is filling up with gunk and stop working properly. I found out the hard way after a good spill. The solution is easy but takes a bit of time.1. Unplug the power and water h ... Danby DDW497W 22 in. Countertop Dishwasher

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

Electrolux Dishwasher Model EIDW6105GB1... no error codes...I select the cycle, everthing appears normal...start to hear water fill, but doesn't progress to point of opening soap container. When I open the door all lights are blinking. I've canceled and tried various cycles, but with same result... all lights are blinking. Even tried just a rinse only. all lights still blinking.... This unit is only 4 years old!


... Electrolux Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Kenmore dishwasher showing error and no blue light but the drain is working but no water


... Kenmore 24 in. 16262 Built-in Dishwasher

KENMORE DISHWASHER Hi, My husband just received a reset "code" for our dishwasher and the light went off and we thought it was going to work. But now no water is going in, we can hear it making like a humming sound and its warm inside when we open the door. Can you guide us?


You probably have a build up of food under the bottom heating element. The excess food falls to the bottom and then clogs up the space where water collects to be heated. The heater works but there is no water to heat, so washer will go on to next pha ... Kenmore 24 in. 16019 Built-in Dishwasher

Hoover dishwasher showing error code E1 seems to start the a few minutes stops. No water filling up but some water in the bottom. What is wrong?


... LG LDF6810ST Stainless Steel Built-in Dishwasher

Indesit dishwasher error codes i have to lights flashing on my indesit dishwasher the second and forth left to right any idea's


Why does the spray arm fall off? ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2828 seconds