Having problems with your Hotpoint 24 in. HDA1000G Built-in Dishwasher ?

Dishwasher completely stopped in the middle of a washing cycle. Any suggestions? I checked and there's no issues with power. It's old and I think something may have been shorted or blown. help ple

\015 I have a Hotpoint dishwasher model# HDA10000G02WH and it completly shut down during a washing cycle. I checked all of the power connections and everything is good. What can I do to fix my problem? Contact me at [email protected] please with any solutions.\015

Answers :

It sounds like the timer. I have replaced the timer because I had the same problem. It now works perfect!
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA1000G Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher completely stopped in the middle of a washing cycle. Any suggestions? I checked and there's no issues with power. It's old and I think something may have been shorted or blown. help ple


It sounds like the timer. I have replaced the timer because I had the same problem. It now works perfect! ... Hotpoint 24 in. HDA1000G Built-in Dishwasher

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Purchased a Bosch SMU50E15AU dishwasher and think the water hose may be too short as the washer needs to be installed in the corner rather than directly next to the sink - read that due to the anti flooding valve may not be possible to extend.. Any other solution?? Please help/advice Rgards


You will have to add drain hose to this type install . do not use a smaller size. 5/8 in ok and no sharp bends . ribed drain hose is good . whirlpool ext hose kit is a good one to use . this should not cause any problems. mm ... Dishwashers

Installed an older model dishwasher for a friend power works oes throuth the cycles but its not pumping water into the uniT there is no clogs and i hear the pump turn on. unsure why its not getting water into the unit another friend thinks its cause the air tube isnt hooked up but i think it may be something more then that any ideas


You will need to disassemble the bottom part where the bottom rotary spray nozzle is(the part that shoots water upwards). The impeller might have come loose or it is clogged in that area. ... Hotpoint Dishwashers

Blanco dishwasher Hi. Saw your answer on the Blanco dishwasher. We have same problem. Dishwasher makes all the pump sounds it used to, but does not start to drain at cycle start, and then no water comes in. read the manual again and think we may have been washing up - ie sinks plugged. Could this have triggered something. You mentioned something about a "micro switch" could you tell me where would this be?. We have a BFDW 650 S. Thanks, Angie


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

I have a Whirlpool Gold Quiet Partner III that is 8 years old and recently stopped cleaning top rack dishes. I remember finding a mylar like piece in the bottom of the tub and threw it away thinking it came off of something we washed (I know, bad thinking.) The mylar piece measured roughly 3-4inx2in and was folded in half. Anyways....the upper arm does not spin and the detergent doesnt get fully dispensed so dishes dont get fully cleaned. I am guessing not enough water pressure to upper arm. Wou


I'm having a similar issue. Are you sure the arm isn't moving at all?\015\012\015\012Generally what I'm finding is either you have a clog or the pump motor is bad.\015\012Hear is the service manual.\015\012 ... Dishwashers

Have a 6 month old UC65E. Machine continues to run. I think the green start switch may be bad. Is there a way to bypass the switch until Monday?


THIS MACHINE USES A COMPUTERIZED CIRCUIT CONTROL BOARD AND THERE IS NO WAY TO BYPASS THIS WITHOUT POSS DAMGE TO THE CONTROL COARD. U MUST STILL BE UNDER WARRANTY AND ANY TEMPERING WILL VOID THAT WARRANTY, I HIGHTLY RECOMMEND YOYU LEAVE THIS ALONE. ... Cma Dishmachines Dishwashers

I have a kenmore ultra wash 11 models number 15715. it isn't doing a good job cleaning dishes anymore and i think it may have something to do with the filter


... Kenmore Dishwashers

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

Have spent $300 in the last week on Haier HDW101ss repairs. It still isnt fixed. The repair guy 'thinks' it is now a faulty timer. The unit hangs at certain points in the cycle. At these points the timer (ticking) noise stops but the machine carries on washing. It will hang at this point indefinately. I have taken the timer out, and it looks brand new (the unit is only 4yr old). Any advise, does this sound like a timer issue, or could it be something else? Where can i source a cheap (2nd hand)


... Haier Dishwashers

I have a Fisher & Paykel fridge (freezer top, fridge lower) probably approx 3 to 4 years old, fridge and freezer works ok, but drips water from top plastic tray below freezer into fridge and into door trays. I'm thinking that defrost or whatever line is blocked (possibly/hopefully ice) Will turning fridge off for a few days fix it ? or is it something worse ? The round plastic bowl/catcher is always empty thank


Hi,\015\012The drain may very well be blocked with ice....that is not at all uncommon...\015\012\015\012Let the fridge off for a day to clear any ice and then blow through the drain to make sure it is open...\015\012\015 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

It appears that water is not running through the dishwasher or that the sprayers are not working correctly. There doesn't appear to be a clog. However, I did find a round rubber "washer" (I think that is what they are called) laying in the bottom of the dishwasher - where does this part go. It was working fine until this wash. The heating element works fine but like I said it appears that something may be wrong with the spray tower. Please advise Model number of Hotpoint: HDA3420Z01BB T


Hi,\012When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Hotpoint Dishwashers

The dishwasher makes a whining noise while washing; It started doing this a short time age. The dishwasher is about 1 1/2 years old. It almost sounds like there is something in the pump, , but I can't find a schematic.


The problem would be either something in sump area of the pump near the chopper or a bad main bearing in the motor. Since it is fairly new I would suspect something in the sump. I have put together some instructions on how to take this apart and clea ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

My dishwasher (Maytag MDBH965AWQ quiet series 300 was purchased in May 2006 (making it just a little over 4 years old). The handle broke on it initially and now the control panel has gone out including the start button. The cost of the replacement parts is right around $200, so I don't think it is worth investing that kind of money into it since it seems to be a lemon anyway. I have always been faithful to Maytag. At the time of our kitchen remodel in 2006, we chose all Maytag appliances. I


Well Kathy, you may be in luck. There has been a safety recall on your model of dishwasher and Maytag will give you a considerable allowance to replace with another Maytag. You may contact them at 1-800-544-5513 with your model and serial number and ... Maytag Dishwashers

Silly Dishwasher Hello, I have a huge problem with my less-that-12-hour-old Bosch SGS56E18GB. We are not generally thick people. We plumbed our dishwasher in, like we have plumbed in many appliances. Switched on the dishwasher for the first time and GREAT!!! Here we go! I can tell this is not going to be plain sailing. The dishwasher has already decided that it wishes to do the short cycle. (19/29mins or something) I Press on then off - no change. Reset, Off - on, still no change. So I decided t


Press and hold scrub and delicate at the same time for 3 seconds then let it cycle turn off it should reset. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

I have a Beko D 2731 FW its about 4 years old and recently it has begun to leave a gritty deposits. I think this may be due to the top spray arm not running as freely as it used to. I would appreciate any help. Thanks.


Hello,Here are a few things to check.* Worn wash impeller (depending on design). Test by placing a glass upright in upper rack with full charge of water in the basin. Run dishwasher for 30 seconds. Glass should fill up. If not, repl ... Beko Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

LG - LDF7811ST Dishwasher will not turn on at all. I have replaced the main PCB board and checked all wires for shorts. The PCB board does have 120Vac to the board. I have also checked the latch and it does close the switch when the dishwasher is closed. I think it may be the main switch/power button board but can't seem to find the part number or alternate part numbers that can be used.


Hi. The likely culprit will be the power switch. The part number for this switch is 5020ED3011A.NOTE_ Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for po ... Dishwashers

Our KitchenAid Superba model KUDS01DJss0 ( about 7 years old and has always worked fine) I think is not heating . . the dishes come out wet and don't seem very clean if they had especially if they have a small a bit of something like peanut butter on them when loaded ( so lately I've been dong a pre-wash by hand). Unit doesn't seem to get very "hot" during the wash/dry and steam does not billow out when I open the door soon after the cycle completes like it used to. It does feel warm to the


Hello. The new heating element will come with a new control board. There are no tricks to the change actually, the easiest way to change the heating element is to unhook the plumbing, electrical, and drain hose then pull it out and get to the back ... Dishwashers

I have a Frigidaire FDB2410LDC3 Dishwasher. It was working great until my 5 year old fell on the door and it does not spring back up now. I tried looking with a flashlight in the sides and the springs may be OK. What is most mystifying about this is something has gone wrong with the part your hand uses to close and open it. The latch is limp so I wonder if there was some other spring in there that broke in the incident. Now after some time of forcing it to shut (due to that pesky latch that


Prhandle and latch.obably sprung the hinges. The reason it dont want to work right is the door latch is not latching properly and therefore it wont start. I would start by replacing the hinges and springs and the ... Dishwashers

Motor on kenmore dishwasher hums then kicks out,will not run , think something may be jammed up in it, how do I get it apart


We have a bosch aqua sensor and it doesnt fill with water ... Kenmore Dishwashers

My Inglis dishwasher (E71195), 13 years old, doesn't clean properly. There is a film on everything that is especially noticable on glassware. I have cleaned every filter and unclogged everything that I could think of. I tried different detergents; right now I am using the same stuff in the dishwasher as we use to clean the milking equipment in our dairybarn because it gives the best result. It still is not as it should be however, there is still something left on the bottom of the glasses. It is


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0969 seconds