Having problems with your Hotpoint 24 in. HDA1000G Built-in Dishwasher ?

Dishwasher won't drain nor will the lower arm rotate and spray. When turned to the ON position it just makes a clank noise (like a motor is trying to turn on) and hum for a short bit. Nothing afterwards. There is water standing in the basin.


Answers :

I don't know if this is unusual or not. But, I found A solution. Thinking about what I said in the problem descriptor, I disconnected the power to the dishwasher. Got to messing around with the electric motor and found it was seized up...don't know with what or how...but it was seized up. So, I broke out the trusty WD 40 and a long thin flat tip screwdriver. Sprayed a bit of the WD on it and tried to move the motor with the screwdriver. Got it to move fairly freely and re attached the power. Turned the nob till it started to run and sprayed some more WD on it. It broke free. Everything works fine on it. If there was a better way to fix it, which I am sure there is, please pot it. This is just the way I found to get my to working. Thank you everyone for your time.
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA1000G Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher won't drain nor will the lower arm rotate and spray. When turned to the ON position it just makes a clank noise (like a motor is trying to turn on) and hum for a short bit. Nothing afterwards. There is water standing in the basin.


I don't know if this is unusual or not. But, I found A solution. Thinking about what I said in the problem descriptor, I disconnected the power to the dishwasher. Got to messing around with the electric motor and found it was seized up...don't kno ... Hotpoint 24 in. HDA1000G Built-in Dishwasher

When i turn my Viking dishwasher on the motor starts to run but no water comes out. It was humming along for several hours before i realized that nothing was really happening. I turned it of and then tried again but the same thing happened. It sound like a motor and/or pump working but no water enters the chamber. Thanks, Jonathan


It sounds like the Water Supply Solenoid is bad. I would change that and let all of us know what happens. ... Dishwashers

Dishwasher turns on water trickles in but spray arm doesn't spin. I hear humming in the wash cycle like it's trying to work but no spray, and little water. Is the motor gone or pump or? frigidaire DW model # fdb510lcso


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Kenmore Elite 665.17053400. Powers up ok, fills up with water ok, but wash cycle won't start. I can hear the motor trying to turn but sounds like its seized up. If I cancel the wash, the machine drains out the water ok. Does this sound like the moter is shot and if so, what should I expect to pay to have it replaced?


This dishwasher has a very sophisticated wash system. In order to improve the wash efficiency it uses a chopper and a soil sensor. It is very likely the chopper assembly is clogged which is blocking the water from circulation and straining the wash m ... Kenmore Dishwashers

I have a Kenmore Elite dishwasher (model 630.17303406) and it just stopped working. Doesn't drain what's left in the bottom and just makes a humming sound when turned on. Power is good, sounds like the motor is working. Doesn't seem like it is drawing water in. I want to check the pump and motor, anybody have any advice?


If nothing obvious like blocked / obstructed outlet pipe\015\012You need to check if the outlet pump motor in line with the outlet hose is spinning when in the outlet mode. First check if it is spinning by looking at it and see if the small fan ... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I turn on the dishwasher and it just hums with no water spraying the dishes. I tried the sani wash cycle and it worked but just one time. Now every cycle is the same - turn it on and just the mild motor noise


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Kenmore Model 1590 Dishwasher, 1985, sitting unused since about 1994. Takes water into tub but never goes through any washing/rinsing cycles; water stands in bottom (I stop it below door level). A click, like a solenoid activation from the timer area, but motor never does anything. Removed the shroud covering what I assume is the impeller, which was stuck, but freed it by turning several times...made no difference. Suggestions??


... Kenmore Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

Kenmore dishwasher fills with hot water but will not wash, just a faint hum. goes through cycle, drains fine, like motor doesn't turn on.


The faint "hum" sound is your wash motor trying to turn on. You either have a piece of glass/tooth pick/ ect.. or a worn out bearing. Its time to change your wash motor. If you do a DIY you can save money over having a service man come out and charg ... Kenmore Dishwashers

Kenmore elite dishwasher won't drain, water stand in bottom. It doesn't sound like pump turn on. We tried to start a load and cancel it to see if it would empty. Didn't hear anything after we pushed cancel button


... Kenmore Dishwashers

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

European Bosch SKT 5002/02. Was disconnected by our plumber to install new cabinets. Not used during winter, as it is never used in winters. Fills with water, makes no noises but does nothing else. Have been told on-line to try to turn the motor (blades, I suppose) but it looks like the whole unit is behind galvanized panels and I don't want to do what I shouldn't......


Hi.Re:"Have been told on-line to try to turn the motor (blades, I suppose)" Someone has probably told you to energize the impeller pump motor directly by jumping its contacts to find out if the motor is working. That is a deli ... Bosch 22 in. SKT5108 Free-standing Dishwasher

Maytag DWU6402AAB dishwasher hums but motor does not run. I've taken the inside apart down to the disk-shaped impeller. It turns freely so the pump and motor are not stuck. When control knob is turned motor hums at the places where it normally should run. The water valve & heating coil seem to be operationg normally. i assume the next step is to test the motor &/or motor relay. Is this correct and how do I do that?


... Dishwashers

I have a Bosch dishwasher model SHU9915 that is 8 years old. It just give a ''hum'' when it tries to go into the wash cycle. It stops humming after a few seconds, like it overheats or overloads, then after a minute or so it tries to start the motor again and ''hums''. It continues this as long as you wish to watch it. Does it sound like the pump has gone out or just a capacitor or something small?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are right the issue is with\015\012the motor; don’t think it’s related to a capacitor. The hum ... Bosch Dishwashers

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure


What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Model #363.14232100 dishwasher. When you turn the switch to on, it will not come on. If you keep turning the knob slowly you can hear the dishwasher trying to start up,but it doesn't. Keep turning the knob and its the same thing, sounds like it will start, but it doesn't. It did fill with water, but once it was opened it didn't start up where it left off. The lock switch was in position, and still nothing. Now I have water in the bottom but can't get the thing to come on. Any suggestions? Help!


... Kenmore 24 in. 16539 Built-in Dishwasher

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1562 seconds