Having problems with your Hotpoint 24 in. HDA3400G Built-in Dishwasher ?

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


Answers :

If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of the disposal, it should go UP and be clipped to the highest point of the inside of your cabinet, then down. Think about it, sh*t flows downhill, but it can't get over a hump. Good luck
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA3400G Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Racks corroding. The dishwasher works great. Just had recall repair done. Problem is the racks are slowly corroding away and new ones cost as much as a new dishwasher. How do I find good used racks and what model racks are interchangeable? The actual model number is mdb9100aww, but it won/t let me enter the ww. Ted


Check on Ebay. I just entered this to check for you. maytag dishwasher racks" and there were several on there. One was universal and could be used with 40 different model numbers. ... Maytag MDB9100A Dishwasher

I turned on my Whirlpool dishwasher last night before I went to bed. It is a model number DU915PwP82. Sometime shortly after that, a water line broke in my neighborhood. The water was off and caused some sort of problem with my dishwasher. There is some water in the bottom of the dishwasher. It won't drain or start washing. Do I need to call a repair man or is there a reset button of some sort. Thanks for your help. Rina


Hi.\015\012Often there is a lot of grit in the water supply after a pipe has been repaired, and this may have clogged one or more of the valves in your line, or the gauze filter in the inlet port on your machine. I would first turn off the wate ... Whirlpool Dishwashers

Model Number 87378918 TD Soft Touch ( 12 years old ) no previous problems. Dishwasher will not complete normal wash cycle or any other fast wash cycle etc. The electronics may be the issue, as the cycle appears to start , then stops and goes to an end beep to advise cycle complete.However, nothing has actually happened. Dishwasher in very good condition otherwise. Will an on site visit be necssary? Cannot locate original guide at present, so cannot refer to any troubleshooting issues. Any a


Hi\015\012\015\012Terry...as the motor works fine then you are right the issue\015\012is with the main board of the unit also known as the electronic control board.\015\012Please check this link and enter your zip code in order to locate ... Fisher and Paykel Dishwashers

I have a kitchenaid model KUDS01JBT dishwasher. The Chopper Assembly keeps pluging up causing the dishwasher not to wash properly. Can I remove the chopper Assembly and run the dishwasher without causing any further problems to the dishwasher or will it cause other problems with the pump etcetera? Thank you for your assistance. Sincerely, Pat


\015\012\015\012Check the water temperature. Should be 125 to 140 F. \015\012\015\012Check pump re-circulation., Listen, see if it sounds like it is spraying the water around with enough pressure. ... Dishwashers

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

I have a Hotpoint dishwasher Model # HDA3500N10BB and it does not drain the water out completely. Actually, it doesn't look like it has drained any of the water out. How do I go about repairing the problem?


... Hotpoint Dishwashers

I have a Kenmore Dishwasher. Model Number 665. Serial Number 15762000. Stock Number FL4413201 Type 280-1 15762 The tag that lists these numbers is a little confusing. The numbers are to the right of the words but don't line up directly, so perhaps all the "numbers" above are shifted down one? Problem: Today (10/07/10) my dishwasher stopped working...for no apparent reason. I inherited the dishwasher when I bought the house about 3 1/2 years ago. I don't know of any extended warran


... Kenmore 15762 Dishwasher

Dishwasher We are having a problem with our Whirlpool ADP5540 dishwasher. We have just moved into a new house with this model dishwasher and have tried running it on a number of cycles. It always seems to stop part way through and the start button then flashes three times. Any ideas what the problem is or how to fix it?


If\015\012this is a blinking "clean light", this is a common problem with some\015\012of the Kenmore\015\012and Whirlpool models. I believe the problem is attributed to water supply\015\012temperatures being too low when filling. Apparently, th ... Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Kenmore dishwasher I have a kenmore dishwasher and in the middle of a cycle all my front panel lights went off. I have checked the power going into the dishwasher it is fine. I also checked the door latch it is fine. Not sure what else to check? Same exact problem model number 665.15934 We have had nothing but problems with all of our sears products - highly suggest to SHOP SOME WHERE ELSE before you get stuck too.


Check the continuity of the thermal fuse (part # 8193762). It's clipped onto the electronic control inside the console.Let me know if you need more help. ... Kenmore Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Our dishwasher won't start (model number 665.16049401). We had a similar problem last summer and a repairman came and fixed it. The problem was that the water level had gotten too low and so the machine locked itself off. This made sense as, at the time, I remembered filling the pool, running laundry and someone taking a shower all at the same time that I turned the dishwasher on. I am guessing this is the same thing that has happened now. The repairman put in a code and the machine worked. Can


Hello,\015\012\015\012ahhhh, you're taking about the reset sequence.\015\012okey dokie :)\015\012\015\012Here it is:\015\012Push the NORMAL WASH then HEATED DRY buttons in that sequence two to three t ... Kenmore Dishwashers

I have a neff dishwasher that is maybe 5 years old. im pretty sure there is nothing wrong with it as it was working perfectly fine before i had a plumbing problem a few days ago. after the plumbing problem was fixed the dishwasher doesnt seem to want to fill any longer. it sounds like it wants to work but its just not filling and going thru the cycle. does it just need to be reset or something? im not sure of the model number as ive misplaced the directions for it. could you please help? by the


Look for the connection from the valve to the inlet of diswasher. Check the hot water valve to be on. It is probably closed when anyone working on the plumping. Good luck. ... Neff 24 in. S5443X2 Built-in Dishwasher

I have an older hotpoint americana dishwasher. It is not cleaning the dishes well and in fact have to wash them first before using the dishwasher. Have checked the drain to make sure there are no clogs and found none. Doesn't have a drain problem, just doesn't seem to actually clean well. Any suggestion as to what the problem could be?


... Hotpoint Dishwashers

I have a hotpoint built in automatic dishwasher model HDA3740G02SA. When my dishwasher runs all the cups on the top shelf seem to have dishwashing soap powder left in the bottom of the cups. I do not over fill the cup where you put the dish washer powder in. It seems like it isn't rinsing the glasses and cups on the top rack of the dishwasher properly. Do you know what the problem would be and how to correct it?


Make sure the arm on top isnt hitting something, each time you load it each in there and spin it to be sure it moves freely, also make sure your rinse agent container is full of rinse agent. ... Hotpoint 24 in. HDA3740G Built-in Dishwasher

I have a Kenmore Elite Dishwasher about 7... Problem with the Kenmore Dishwashers I have a Kenmore Elite Dishwasher about 7 years old. The Model # is 665-16462300. It works beautifully, except that about every 2 months the spray flow intensity ( and the cleanliness of the dishes) drops significantly. The cause is the metal screen located just upstream from the sump is clogged with food particles. I have taken apart the dishwasher several times to remove, clean and replace the screen. This fix wo


Check the inlet hoses; if the catch screens have sediment build up, that will reduce the pressure of the rinse water. Also, look for missing plugs on the rinse arms... ... Kenmore 24 in. 16462 / 16464 / 16469 Built-in Dishwasher

How do i replace the lower spray arm tower on a hotpoint dishwasher model number hda2100v00ww


... Dishwashers

I have the dishwasher model number FGHD2433KF, I have noticed the last few times I try to run the short cycle that after a few minutes it jumps to 99+. What could be causing this and how do I fix it?


Sounds like the control board is having a communication error. Reset the unit at the circuit breaker and retry. If it happens again contact the manufacturer for a repair. ... Frigidaire FGHD2433KF Builtin Dishwasher

My dishwasher (model # DU81ODWGU1) is leaking water and suds during the wash cycle. I ran out of dishwasher powder so I had used regular dish soap for this cycle. Did this cause the problem? My dishwasher is 11 years old.


MOST DEFINITLY You can put regular dish washing liquid in a dishwasher will do that every time take a few washings to stop run 2-3 times empty it will stop. ... Whirlpool Dishwashers

Hi, I get a problem reading " E4". I have now switched the machine off and on again, but still it says the same. Incidentally the machine has already pumped the water out, so the 'overfill" is actually not supposed to be a problem. It is KELVINATOR EXTREME CLEAN DISHWASHER, model KD14SS. Please help, how am I to get rid of this problem, I really do not have the time nor the money to get outside help! Anita Kleynhans


... Kelvinator MDP531RF Dishwasher

How to find problem and repair my Bosch dishwasher, European model?SKT5002/02 is model number. One site suggested trying to manually turn the impeller on the motor as it might be stuck from not being used since last fall. But how do I get to the motor? This is a European model used in Europe.


... Bosch Dishwashers

I have a 12 year old Kenmore Ultrwash Model #665.15951790. I recently replenished the rinse aid dispenser and am experiencing an oversuding problem. It was oversuding to the point that suds were coming out the bottom of the door. Did notice that the blue rinse aid seemed to have leaked into the dishwasher due to a puddle of blue rinse aid at the bottom of the dishwasher. Have run a "quick rinse" cycle 4 times with no dishwasher soap added and still have sudsing. Can the rinse aid cause oversudin


... Kenmore 15129 Built-in Dishwasher

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2692 seconds