Having problems with your Hotpoint 24 in. HDA3400G Built-in Dishwasher ?

My Hot Point Dishwasher is leaking water. It was

\015 My Hot Point Dishwasher is leaking water. It was on the wash cycle. Water every where. Can not see where it is coming from. The model # is HDA3400G02BB\015

Answers :

Hi
\015\012
\015\012
\015\012Check for any kind of leaks around lower spray arm or soap door. Replace the arm if any cracks are found. Also make sure that door latches firmly, and the gasket is not cut.
\015\012The leak can also happen due to a broken fill valve. To check, take off the access panel from the front of the dishwasher so you can reach the fill valve attached to the metal bracket. Use a multimeter to check the continuity across the two black terminals at the top of the fill valve. If it reads 120 V, replace the fill valve. Make sure the thin filter screen between the bracket and fill valve is not blocked by debris.


\015\012Please post back for any further assistance.
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA3400G Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

My Hot Point Dishwasher is leaking water. It was


Hi\015\012\015\012 \015\012Check for any kind of leaks around lower spray arm or soap door. Replace the arm if any cracks are found. Also make sure that door latches firmly, and the gaske ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and


... Dishwashers

Dishwasher leak My dishwasher has a slight dip leak on the copper hose that rund from the hot water. The leak is between the copper hose and its connector nut. I tired fixing it with plumbers tape but it still leked out the sides of the tape.


Tape won't solve this issue. The fitting I assume is a compression fitting which is a ring on the copper pipe that is compressed when the nut is tightened. If tightening the nut won't resolve the issue, then you will need to cut the copper behind the ... Dishwashers

I have a single draw Fisher and Paykel dishwasher. I stupidly put washing up liquid in the dishwasher which resulted in a F1 problem. Water started leaking under the draw and onto my floor. I turned the dishwasher off at the power point and have cleaned up the leak. Have I damaged my dish washer? How do I fix it?


Ok , F1 means your flood switch has activated, which is underneath the drawer. now they show the F1 fault because of 2 reasons.1st there is still water underneath drawer causing switch to activate. 2nd your activator board which has the flood switch ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My GE Profile model PDW9280N00SS dishwasher is 3 years old, and has the SmartDispense feature. Over the last month or so, a noticeable amount of detergent is leaking into the dishwasher between cycles. The dispenser is not clogged, and it does not contain water at this point. I also exclusively use Cascade liquid detergent. What needs to be done to correct the leaking detergent?


... GE Profile PDW8600J Built-in Dishwasher

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

I have a Whirlpool DU9000XR-9 dishwasher that was leaking. No leaks were coming from the bottom of the tub or any connections, etc. I replaced the door seal where it closes on the tub. There is still a leak on the bottom of the door. Can you point me to a possible issue(s).


... Whirlpool Dishwashers

I have a 12 year old Kenmore Ultrwash Model #665.15951790. I recently replenished the rinse aid dispenser and am experiencing an oversuding problem. It was oversuding to the point that suds were coming out the bottom of the door. Did notice that the blue rinse aid seemed to have leaked into the dishwasher due to a puddle of blue rinse aid at the bottom of the dishwasher. Have run a "quick rinse" cycle 4 times with no dishwasher soap added and still have sudsing. Can the rinse aid cause oversudin


... Kenmore 15129 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have an old Bauknecht dishwasher GSF 3160 S that a friend gave us 10 years ago. It was stored for that time, and now if I try to use it, it leaks out through the bottom and floods the kitchen. I would like to know 1) is it worth fixing from the point of view of how energy/water efficient (or inefficient) an old dishwasher is - if you know the specs for this particular machine, and 2) what needs to be changed if it is worthwhile fixing. I don't know what else might not work, because I only pu


... Bauknecht Dishwashers

I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v


... Asko D1876 Dishwasher

I have an LGF6920ST dishwasher, puchased 18mos ago. since i've had it, it's gone from marginally ok to bad, now leaking puddles onto my floor from the lower left side (as i face it) of the door. besides occasional poor drainage, smelly water in the bottom to horrid cleaning (yes, it's attached to the hot water, i use rinse agent, etc) i rinse my dishes, in fact scrub them before putting them into this dishwasher, and honestly they come out nastier than when i put them in...primary concern righ


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers

The dishwasher has a small leak that appears at the floor when it is in the filling cycle. Not too bad at this point, but I took the bottom panel off to inspect, and it?s not leaking from the supply hose, but further up on the body of the washer. any thoughts? thanks


Many of the manufactures today have gone to a plasticcorrugated drain hose on there dishwashers. These hoses have been trouble forleaking!!. Where the drain hose makes a bend it seems to get weak and splits =water on the floor. If you ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Dishwasher not filling w/ water hot point - Dishwashers


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Dishwashers

Water usage for the Kenmore 2 Draw Dishwasher - 465.1332. I am considering an ''instant'' Hot Water heater, or a Point of use hot Water heater. I am unsure of the size to get since i do not know how much water is used per cycle.


... Kenmore Dishwashers

My dishwasher is leaking from underneath, front left as you look at it. If i go underneath it, there appears to be a seal on the outside (it does not appear to be the one that runs along the bottom of the inside of the dishwasher) that has come away at one point. Do you know a) how to get the front panel off (the bit that makes it look built in),b) how can i get another one of these seals. I assume if i get one we can just fit it into place. Many thanks, Robyn J


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012p80897 ... Neff 24 in. S5453X1 Built-in Dishwasher

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

My hot point dishwasher is not draining,after all cylces are complete there's always 2 or 3 inches of water on the bottom of the washer, what is causing this? I have a Hotpoint dishwasher 24" built in. The switch won't come on just hums. When I oprn the door ther is 2" of water on the bottom? Any solutions . Where is the reset button on serial number hda430vww, hda400vba> Thank you!


... Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1976 seconds