Having problems with your Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher ?

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Answers :

Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair.
Wow, slow down. you should be looking for something simple. make sure your door lever is in the off position and or the timer at the off position for safety's sake. take bottom cover off. turn the fins on the motor counter clockwise. the seals in the motor pump assembly may be stuck. this is a very simple design washer. good luck.
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers

When I replaced my garbage disposal I forgot to remove the knockout tab that would have allowed my my bosch SHE58C05UC dishwasher to drain into the disposal. I discovered my error the first time I ran my dishwasher and discovered that none of the water had drained. I then removed the knockput plug and reattached the drain line. My dishwasher now drains correctly but makes a loud sound whenever the pump turns on. Have I ruined my pump or is there something I can do to eliminate the loud noisy pum


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thank You for using\015\012FixYa. To start with check the pump and try to clean it out, then check drain\015\012hose for any obstructio ... Bosch Dishwashers

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

I have a Bosch Dishwasher, Model SHE46C06UC. No mater what cycle I start it in, it simply activates the drain and continues to run without ever starting. Within the last week prior to the dishwasher not working, I noticed a low hum/vibration emitting from the dishwasher. I've clean out the screen and drain filter, removed the pump cover to check for any debris. I've manually added water and it does drain. Additionally, the drain cycle continues to operate even with the door open.


First thing you may want to check is the door switch. You can pull it off and measure the resistance with an ohmmeter. If you get good reading while pushed in and none while switch button is released, then it is a good start. Next, you may want ... Dishwashers

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

I have Frigidaire model FDB130RGS3. This seems like a pretty cheap dishwasher that is provided by my management company. This is third dishwasher I've had in this apartment. The others have all broken. Now this one, which is less than 6 months old, seems to have broken. It does not clean the dishes. I removed the round plastic cover in the base of the dishwasher and the bottom of the dishwasher (sorry don't know how else to describe this) is filled with dirty water. I drained the water and tried


Hi,\015\012\015\012the round plastic cover in the base should just push back on, but you need to make sure it is correctly rotated before doing so. It should look like this:\015\012\015\012\015\012 ... Frigidaire FDB130 Built-in Dishwasher

Bosch dishwasher Over the weekend my drains backed up into the dishwasher. After cleaning the drains I ran the dishwasher 3 times. Under the screen there is still about an inch of water. I never noticed this before because I never removed the screen before. Can you tell me if this is normal or is there a problem with the dishwasher. The water in the little area below the screen is clean.


Its normal. its there to keep moisture around the rubber seals so they dont dry out. ... Dishwashers

Ge profile dishwasher not draining Model no. pdw9280n20ss I checked the drain line at the garbage disposal. No blockage. Line is clear. The back flow loop is high and not kinked. Only a small trickle of water comes out of the disposal drain at the end of cycle. No forceful pressure of water like before. I removed the smaller grill drain area and cannot feel any objects down in there. I do not know how to remove the larger fine mesh grill on bottom. Any suggestions?


Did you ever figure out how to remove that large mesh bit? I am stuck at the same spot and would love a hint. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

Plumber installed new garbage disposal without removing plug. Dishwasher ran all night without draining. I removed plug and it drained but now the dishwasher doesn't have water coming out of sprays. Is the motor burned out?


Spray's are most likely clogged with food debris,carefully use a small nail or similar object to clean them out. ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

I have a Whirpool DU1145XTPQA dishwasher... It has started "Not Draining the water" at the end of the cycle. Dishwasher is only 2-3 years old. I have completly disconnected it and have taken it to my garage so It could be tested in a more userfriendly envoronment... I have found no blockage of any line..... The screen in the dishwasher is completely cleen...yet , when you press drain, It drains at a very very slow rate. I have noticed a small 40 Watt pump (drain pump) that attaches to the mai


There is only one motor that drains the unit.it seems to me that the impellar wheel is not turning fast enough to do the job,you have eliminated all other possible cause with the exception of the main board.\015\012\015\012replace the dra ... Dishwashers

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

Bosch dishwasher = machine on but no water, so the lower basin has water in it and because of it the FLOOD CONTROL SWITCH IS ON, so how do I drain the rest of the water so the FLOOD CONTROL SWITCH goes off? A plastic cover with a seal is stopping me from drain the water below?


If you can see the water use a shop vac if not you will have to pull the unit out and remove the left side panel after removeing the water you will need to find the leak that caused the bottom to fill with water ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Bosch Model SHV46C03UC/14 Dishwasher won?t drain completely. The drain hose is not kinked or obstructed and it drains into the garbage disposal. If I push the combination of two buttons on the panel, I can pump out residual water, but if I don?t, it stays there. It will become foul smelling within a day if I do not manually remove the water. Bosch technical support won?t talk to me unless I am a service technician, but I can handle this as I do all my appliances. The screens at the bottom o


THE DISHWASHER DO NOIT DRY THE DISH ... Bosch Dishwashers

Dishwasher only faintly comes on. The detergent compartment opened but, there is a great deal of detergent residue on the inside of the door. Additionally, I removed the "mesh" drain grates from the base of the dishwasher and they are covered with chemical buildup. I was able to remove a good deal of chemical buildup. When the dishwasher would come on before, you could here the cycle start up, you could here the water, etc., now it is very faint, and you can barely hear any sound.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Asko D3531XLHDSS Stainless Steel Built-in Dishwasher

My dishwasher leaks water from the top of my sink when in the drain cycle mode causing a mess on the counter top. How do I stop this leak? The plastic cover to the part which is located next to the faucet is cracked but there appears to be no leaks on the hose or on the part itself. Also, what is the purpose of this part? Is this the actual drain for the dishwasher and if so, why doesn't it tie directly into the drain?


... Whirlpool Dishwashers

GE model GSD600003 repair manual: Before you answer this, please tell me if I will be charged for the answer, in case I'm not interested at this time. Do you have a diagram of the drain area and water inlet area? I took apart the plastic drain cover for cleaning because it was had pink mildew all around it where residual water pools. I cleaned it all up and put it back and now the dishwasher doesn't fill with water (none comes in). I'm just a guest trying to troubleshoot for relatives, so I'm


I'm not sure how mildew can grow in a dishwasher that is working well, but after cleaning it and putting things back together, it does now seem to be working. I thought that the water wasn't filling but I guess the heating element heats up before the ... GE Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2686 seconds