Having problems with your Hotpoint 24 in. HDA900X Built-in Dishwasher ?

Motor will not start

\015 Hotpoint HDA 900x....Water starts process, but motor will not start. Had this problem before, repair tech stated if dishwasher not used often a reset switch had to be reset? Where is this swith located?\015

Answers :

Hi, the reset switch is located on the inside of the dishwasher. its on the actual motor. here's a tip to keep the motor operational during low usage cycles.


If you do not use your dishwasher often, set it to fill and pump out once every week.
This will help keep the seal moist, and the garbage disposer clear. it will also keep the motor form deactivating itself.
Repair Help & Product Troubleshooting for Hotpoint 24 in. HDA900X Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

My RMW 2.2G24 will not discharge water once the motor is running. When motor not running the water will flow through. It also appears the pump locks up every now and then becasue I cannot pull to start the motor. Bleed pressure and motor will start.


... Annovi Reverberi RMW2.5G25D

I am getting a buzzing noise from my electric motor. i tried changing the capacitor but still no change. The motor starts up sometimes but starts making a noise.Isusupect the winding or a bearing in the electric motor. How do I strip the motor from the pump?


First thing you must check the machine with load, without load with water fed, and without load with no water fed. Then check the simpler cause. See if the cooler fan is hitting the casing.\015\012If you check machine without pressure load and ... Karcher PSI Electric Pressure Washer

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

SORRY FOR MY ENGLISH .I HAVE A FAVORIT 54750 WHEN I START ANY PROGRAM IT FILLS NORMAL WITH WATER AND THE MOTOR BEGINS AND RUNS BUT AFTER A FEW SECONDS THE LIGHTS VORSPULEN-REINIGEN-SPULEN STARTS WINKING I HEAR AN ALARM SOUND AND THE PROGRAM STOPS. THE MOTOR HAS TWO YELLOW WIRES THAT TELLS THE PROGRAM IF THE MOTOR RUNS .I TRY TO MEASURE THIS WIRES WITH A MULTIMETER IN OMMS AND SEEMS NO CONNECTION BETWEEN OF THEM.


... Stainless Dishwashers

The dishwasher started making horrendous noises. I removed the bottom panel and narrowed the noise down to the motor (the noise starts and stops when the motor kicks on and off). How do I remove the motor to visually check it out? I thought I had all of the screws removed, but it feels like something is still holding it in place. thanks My model number is GSD4060N10SS (GE Dishwasher)


... General Electric GSD4060NSS Built-in Dishwasher

MaytagMJD2005 Machine is in middle of cycle power on. water on. The main pump motor attempts to start. motor spins so the pump is not jambed. pump out pump starts at the same time. Motor does not overheat.


So what is the problame it jusy seems you telling us there isnt one and u have solved it and giving advice. ... Maytag Dishwashers

GSD2200G00WW. When starting washer, part of the time the machine will not start, other times if machine has been running for a while and you open the door and try to restart the machine it will not restart. You can hear the motor humming as if it wants to go but it will only restart if you turn the motor shaft even just a little. I am wondering if the electric motor is dying??


... GE GSD2200G Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

Hello I just borrowed a k archer k 2.87 water blaster from a friend and forgot to turn water on before starting motor. Motor stopped after a few seconds and now won't start. Online guide says to change fuse but nz version doesnt have fuse in plug. Do i have to take machine apart?HELP Please!


Most of the time it is the GFCI on the end of the plug that goes bad. If it were me I would cut off the GFCI and wire in a standard 120v plug. If it still doesn't work after that then there is a good chance that something electric internally has gone ... Karcher PSI Electric Pressure Washer

I accidentially sprayed water on the pressure washer motor and got it wet and the pressure washer stopped and won't start up. Will it start back up after things dry out or is the motor broke?


Yes it most likely will, BUT you need to dry OFF ALL electrical items well.\015\012\015\012Check also that you haven't dislodged anything from the system.\015\012\015\012If it still will not go, you may need to use WD40 or similar water d ... Pressure Washers

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

Problems with my Karcher k2. It just stopped dead. On removing all the casing i was able to move the fan at the rear of the motor and it started up, but on stopping i had to move the fan manually for it to start again . are there brushes on the motor that are worn, if so where can i download detailed drawings. Regards john.


Sounds to me that you might just want a replacement capacitor which is on the side of the motor. Thanks Shaun. ... Karcher K2.26 Electric Power Washer

Why does drain motor start when pushing the start button on the door before the door is closed?


It's almost certainly the float switch in the bottom of the machine. In the bottom is a polystyrene 'float' that is either active due to water in the bottom or is faulty. Tip your machine to the side and remove water and try again, bridge or replace ... Bosch Dishwashers

Blown Motor DW is about 16 months old. Started making some real bad noise. Lasted about a minute and then had a death howl. Called in repair tech who says motor is blown. $399 for repair which includes $125 for the part. I've rebuilt car engines, so can probably replace a DW motor. Any insight on how to replace the motor? is it worth paying 275$ for labor? Just bugs the hell out of me paying $400 bucks for a repair when i can get a new one for $450.


I haven't changed that particular brand of dishwasher motor, so I cant give a step by step, sorry. I do know the other brands it is optional to get the motor alone or the motor with the pump assembly attached, so you may want to ask abo ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a Frigidaire Dishwasher model #FGBD2431KBO. The problem is when I push the start button it fills with water and then will not start wash cycle. If you push the start button again to stop and again to start then the washer will empty the water. So it seems that the motor runs only in one direction.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

I have a Kenmore dishwasher, and when we shut the door, without starting a ccyle or anything, the motor will start going!! When we do start a cycle, it will get stuck at some point during the cycle and won't sanitize or show the "clean" display light as being lit.


... Kenmore Dishwashers

Beko dw600 integrated dishwasher will not start cycle. all conections are ok, salt in, rinse agent in but will not start washing cycle. motor starts but cuts out after 10-15 seconds then nothing?


... Beko Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0924 seconds