Having problems with your Hotpoint-Ariston LFT 321HX Dishwasher ?

Lcode 1 flashes and drain pump doesn't stop


Answers :

The flash code means there is water in the base panel underneath appliance first check the support on your lower arm isn't loose then leave to dry out
Repair Help & Product Troubleshooting for Hotpoint-Ariston LFT 321HX Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Lcode 1 flashes and drain pump doesn't stop


The flash code means there is water in the base panel underneath appliance first check the support on your lower arm isn't loose then leave to dry out ... Hotpoint-Ariston LFT 321HX Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Hello My zanussi diva edw1500 stopped working half way through a wash and there is i30 flashing. According to the manual this is some protection against flooding. I thought it was my external drain was blocked and this was stopping the water from being pumped out of the machine. The drains have now been unblocked but when I tried to resume the dishwasher cycle ther same error appears. Please can you advise? Many thanks. Kind regards Jo


... Zanussi Dishwashers

The dishwasher pump sounds like it is trying to drain, even when the stop button is pressed and the door is opened. The only thing that stops it is turning the power off at the power point. However, when the power is turned on the pump continues. The wash cycle icon flashes, but the usual cycle indicator is not lit at all. The dishwasher will not commence a new cycle.


... Asko D3122XLW / D3122XLB Dishwasher

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Hi, Zanussi dishwasher DE6344, when starting any program the machine start pumping (draining) for a while and then stops, lights start flashing saying that the draining is faulty. Checked the drainpipe and when adding some water the machine drains it perfectly, still the program won't start. Looks like it thinks there still water inside ? Suggestions ?


... Zanussi 24 in. DE6544 Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Neff s5443x1gb/07 drain pump starts at beginning of any cycle then stops. when due to fill with water nothing happens and the end light is flashing. there are no blockages. is there ant way to check the supply hose which is in one with the valve or could it be something expensive?


... Neff 24 in. S5443X2 Built-in Dishwasher

Miele dishwasher starts pump runs then stops and inlet drain light flashes


Here is a manual for servicing it.http://ww2.justanswer.com/uploads/smitty1486/2011-11-25_043923_g600__800_miele_service_manual.pdf ... Miele Dishwashers

My asko 1585 overflow switch is activated. I fixed the drain problem now how do I stop the pump from running and the lights from flashing?


Hi drlebo,\015\012\015\012You can go about that one of two way's. 1) wait a day or two until the water in the overflow basin evaporates enough to satisfy the "overfill float switch" or...2) remove the toe panel and soak up the water in the basin with ... Dishwashers

Whirlpool model du1100xtpq6 machine will not start clean lite flashes 7 times stops and repeats must be code 7 blinks only drain pump runs when drain/cancel button pushed


Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again. ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Miele G 870 SC dishwasher had blocked drainage due to stopped up sewer which got snaked out by plumber. Ever since, the drain pump won't stop running. Have cleared the trap, filter, and drain-filter and still the pump runs continuously.


Hi\015\012\015\012The problem is with the float switch mechanism located at\015\012the bottom of the unit...either this has gone bad and should be replaced or the\015\012pump itself is bad & should be checked. Hope this helps...please pos ... Miele 24 in. G870 Built-in Dishwasher

Have a Zanussi 6344 dishwasher, when starting the machine it starts pumping en then stops. When adding water the same problem, starts pumping to drain the water and then stops again ? It drains perfectly, seems the machine thinks there's still water inside, is there some sensor that checks the water level or so ?


... Kuppersbusch 24 in. IG6344 Built-In Dishwasher

My Bosch SHX46A06UC/42 stopped working today. I can hear the drain pump constantly pulsing about once every second. I checked the control board and found a relay contacted burned. I re-soldered the relay so it now has a good connection, however the drain pump still just pulses. How do I verify if the drain pump is bad or if the relay failed, or yet another problem?


... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0931 seconds