Having problems with your Hotpoint Dishwashers ?

I have a Hotpoint Super Plus dishwasher 7820. It worked well for a long time. Towards the end of the cycle it leaks a lot of water from the underside of the door, so it seems. I have fitted a new door seal. No success. What may be the cause?


Answers :

The door seal has to be in a proper position completely around the door (including the bottom area of the door). If not, it will leak. Also, there are two black corner baffles/seals (located in each front corner inside the tub area) that may also be the culprit. Additionally, there may be an issue with the float switch assembly that shuts off the water supply prior to the wash cycle. If the float switch assembly is allowing an extra amount of water in the tub, it will cause a leak.
Repair Help & Product Troubleshooting for Hotpoint Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Hotpoint Super Plus dishwasher 7820. It worked well for a long time. Towards the end of the cycle it leaks a lot of water from the underside of the door, so it seems. I have fitted a new door seal. No success. What may be the cause?


The door seal has to be in a proper position completely around the door (including the bottom area of the door). If not, it will leak. Also, there are two black corner baffles/seals (located in each front corner inside the tub area) that may also b ... Hotpoint Dishwashers

My Zanussi DS17 slimline dishwasher is leaking from below the door at the front. The inside seals all seem to be fine, but the catchment moulding below the door (which is revealed at the front when the door is opened) is filling up with water, and then overflowing. I can't see where the water is comming from, but it is definitely the water from the washing cycle as it's hot. Any ideas? I haven't dragged the maching out from the wall yet, but I may have to. David R


Hello,\015\012Have a look at the bottom spray arm and check the ends of the arm for splitting as this will cause the water to be directed at the door lower section and leak.Try taking arm out and run for a short while and see if it stops the le ... Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

We lost electricity very briefly today which caused the dishwasher, washing, drying, clean buttons to blink when the electricity came back on. I opened the door to do a load of dishes hours after the electricity came back on and the basin was filled with water which caused water to spill out of the dishwasher. The basin was empty last night when we used it. It seemed to fill up when it was not running.


It seems unit fill valve is stuck open and water is coming in even when machine is off.fill valve opens up only when u start the unit.2 chks this u can open the door and look at the hole inside from where water comes in.if water is coming in with do ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Ge Triton dishwasher GSD5500GOOWW was not cleaning like it used to- I cleaned screens at back bottom-very dirty- also-detergent cup stuck opne - took door apart and got it unstuck - it works fine now. - it seemed to do better but now it is cleaning poorly. It seems to fill and start a lot sooner than before - after 30-45 seconds it starts up. I tested the water temp and it is 90 degrees! Hot water coming in is at 105 degrees. Also - it is leaving a white residue on dishes - didn't do that be


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers

Model number 665.13763k600 Seems like dishes on the top rack do not get hit with a lot of water. Also, when soap packets are put into the soap compartment, the soap packets no longer dissolve. It appears that there may be a problem with water flow. Have had the unit for a few years. Wondering if it could be a filter or something?


... Kenmore 24 in. 16039 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Our Maytag MDB5000AWB has stopped using all its soap. Instead the soap just seems to run down the door and stay gooey (same Cascade we've used for years). I cleaned all the water jets to no avail. Also, the dishes don't seem clean and there is lots of soap spotting. Tom S.


Try running some type of delimer through a cylce or 2, like lime-a way or clr. Not with dishes though. ... Dishwashers

Hello, Im trying to diagnose poor cleaning of glasses in the top rack of my Fridigaire FDB751SCB0. everything seems to work fine but while testing I noticed the upper arm isn't spinning. the lower arm is. i believe the pump is working as water is spayed everywhere inside but no matter which position I leave the upper arm in, I find it in the same place when I open the door. what could cause the upper arm to not get water preventing it from spining?


Hello; first thing to check, which you don't mention, is which side of the glasses aren't coming clean; the outside, which would be caused by the TOP spray not working properly, or the INSIDE, which would be caused by the spray BELOW the top rack not ... Dishwashers

Top rack water does not seem to be causing arm to turn. tried to reallign water but not successful


There is most likely a clogg in the very tiny holes in the spray bar due to calcium build up or the arm is not inserted all the way or leaking at the connection. Chat away................. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Rinse Aid dispenser seems to use a lot of product. Could almost need to be refilled daily. Is there somewhere or somehow to determine where an internal leak may be or to check that the rinse aid door is leaking or is not the problem. This seemed to happen very suddenly. This unit is approx. 6-7 years old. The rinse aid settings have not been changed.


Turn the settings down. the amountof rise aid dispenced. ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

I have a Diplomat Fully integrated dishwasher model ADP 8242 when put on any program it fills and seems to be washing then stops after 5 minutes and the dispenser door has not opened. There is a lot of water left in the bottom of the machine which is cold water. Any suggestions?


Check the small drain pump. Possibly its asking the pump do drain to allow for fresh water, but because low level is not detected it shuts down. The dispenser draw normall opens when the hot wash cycle starts.When you think its washing,briefly open d ... Dishwashers

My Maytag MDB 4000 dishwasher is leaking from the door at the lower left front corner. The seal seems to be OK and the water is at the proper level. It runs out of the door when the cycle shifts and on other occasions. Any idea what might be causing it?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Maytag 24 in. MDB4000 Built-in Dishwasher

WE HAVE A 3 YEAR OLD BOSCH DISHWASHER WHICH NOW HAS PRESENTED US WITH A PROBLEM. DURING A WASH CYCLE IT APPEARED TO MAKE SLIGHT NOISE WHEN WE DECIDED TO INTRRUPT THE CYCLE BY OPENING THE DOOR AND CHECK THE CAUSE OF THE PROBLEM. WE NOTICED THE WATER IN THE APPLIANCE HAD NOT DRAINED. WE PROCEEDED TO CHECK THE FILTER WHICH SEEM TO BE FREE OF ANY REMANANTS OF FOOD AND ANY OBJECTS. THEN WE FOLLOWED WITH THE CHECK ON THE PUMP FOR SAME AND FOUND NOTHING THAT WOULD CAUSE A BLOCKAGE. WE DECIDED TO R


... Bosch Dishwashers

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

Our dishwasher is leaking lots of water from the bottom of the door. It is even causing the breaker to blow. Could it be the seal or maybe the hose issue that was mentioned above?


Hi, W/D here.Most likely, it is the seal, but it might also be the door sweep. Here is a good video, with a good place to start:http://www.youtube.com/w ... Maytag Dishwasher

Dishwasher has stopped during programme - door may have been opened during cycle??!! - although cycle had only just started. bottom of washer has water in but cant seem to restart on ANY programme - pls help!!! have turned off at power and back on etc - no joy :(


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

I have a Bosch DLX Series dishwasher. The cycle seems to take hours to run. I was told that this may be caused by the water not heating up enough? Comments?


Have checked it does get hot enough through the wash cycle. ... Bosch Dishwashers

I have a Bosch SHU43C. I have a leak it seems to come out from the door. I removed the front panel. Inspected the seal and all seemed smooth and not damaged in any way. So I decided to run the machine. Waited for a few minutes and the water leaked from both corners at the same time. The water settled in the rubber trough under the door. After a few more minutes the water leaked over the trough and onto the foor. Is there to much water entering the machine? What limits the water entering


... Bosch 24 in. SHU43 Built-in Dishwasher

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1361 seconds