Having problems with your Hotpoint Dishwashers ?

No water is geting to dish washer - Hotpoint Dishwashers


Answers :

The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation may take a couple minutes to start a fill. If you have power and it's not clogged up replace the valve .If you have no power to the water inlet valve check float switch. This can be done by checking the continuity. Here is a video checking the water inlet valve and the float switch. It may be a different model but the testing procedure will be the same. You can also enter your model # for diagrams and illustrations for most models. All parts come with installation instructions.

If you've not changed anything on your water system and you know that you have water pressure at the machine, the problem is in one of two things: The timer isn't turning on the hydromechanical valve, or it is the hydromechanical valve itself. Both of these are common problems that are easily solved. A tech call will be in order, or if you're handy, test these two items with an ohm meter for power to the valve. If you have power (this means timer is good - remember to set it on "fill") and can hear an audible click in the valve when you energize it (with water pressure attached), the rubber diaphragm is bad. If no click, something is wrong with the valve coil. Replace items as indicated. The entire valve will need to be replaced if either no click or click and no flow.
Repair Help & Product Troubleshooting for Hotpoint Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water is geting to dish washer - Hotpoint Dishwashers


The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you g ... Hotpoint Dishwashers

Dish washer will run but no water comes out. - Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher


Sounds like your float switch is stuck in the up position. If not you need to check your water inlet valve to see if it is clogged. If you don't hear it click when you turn on the dishwasher it's either stuck in the up position or needs replaced. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

Water is not draining from the dish washer. - Hotpoint 23 in. BFI62 Built-in Dishwasher


Hi,Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain out ... Hotpoint 23 in. BFI62 Built-in Dishwasher

The model number for the hotpoint dishwasher is HDA110S48BA. The washer had water inside once the cycle finished and the dishes were not fully clean.


... Hotpoint Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

Samsung 9E Error - Low Water Level. Dishwasher has worked fine (10 months old). Confirmed adequate water supply/availability. When opening the dish washer after error, the inside has no standing water. I can hear the dish washer initially fill. This happens later in the cycle (maybe 10 mins in) Should I replace the fill switch/sensor. Is there any info available on how to fix it my self. Appreciate your help!


... Dishwashers

My dish washer isn't cleaning the dishes well. There are little particals inside of every cup and on dishes after it is done. I just emptied and and now I'm running it with bleach. But before I started it I looked at the drain hose under the sink. The drain hose had water in it. The drain hose is going uphill from the dishwasher to the sink so I don't know if this is normal to have some water in the drain hose when the washer completes since it's not would have to pump uphill to get to the garba


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I own a build-in LG Stainless Dishwasher (modle: LDF1178ST). It stopped draining water during its recent startup due to its idle (no operation) for about a year:). I can only feel the hose full of water by touching the drain hose between the washer and the sink desposal. It's hard to check other part of dish washer since it's built in our cabinet. Could any dishwasher expert help to advise how to trouble shoot or fix this problem. Thanks, Alex Chen 571-220-7484


There is a float in the bottom of the dishwasher that tell the motor to turn on and pump out the water. I would check the float first to see if it is hung up and not raising to tell the dishwasher that there is water in the base. Check the check valv ... LG Dishwashers

Dishwasher does not get enough water. Dishes are always dirty after running dish washer. The center part where the water is suppose to spray out of doesnt even pop up to allow water to spray dishes thru out.


Check your water inlet screens, and the pump for blockage of some sort or no pump operation condition ... GE Nautilus 24" Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

No water is getting inside my Bosch dishwasher compartment. Water supply to dishwasher is ok. Checked hose at input of dish washer and water supply is ok. Could pump have packed in? Model 004 920 378. Dishwasher used daily since 1999.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

I have a 8 year old Bosch dishwasher model # shu3032uc /14. There is no water getting in. I put water in, turn the dishwasher on and the water drains out. I do not see any water under the dish washer.


I have covered this in several previous solutions for Bosch dishwashers. I have copied the text below from a previous request for help, rather that write the entire thing again.\015\012 \015\012If this doesn't help, ple ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

Can you change the temp of the water coming in the dishwasher? Other than the temp from the hot water line. The temp to the sink is very hot but when you open the dish washer the water just seems very warm. I didn't know is there a temp setting for the dishwasher?


THE WATER LINE TO THE DISHWASHER SHOULD BE FROM SAME HOT WATER LINE TO THE SINK. RUN THE HOT WATER IN THE SINK UNTIL HOT THEN TURN ON DISK WASHER AND CHECK THAT THE TEMP IS CLOSE TO SAME TEMP. HAVE SEEN COLD WATER LINE USED. YOU SHOULD BE ABLE TO SEE ... Samsung DMR78AHS Builtin Dishwasher

Dishwasher continually beeping midcycle. Open washer - dishes wet, water in bottom of dishwasher and water faucet sign illuminated. Can anyone advise what's going on? Just checked the water valve to make sure it was open. Thanks.


... Thermador DWHD630GPR Builtin Dishwasher

Hi, I have a Miele G681 dish washer with an intake/drain light problem. I've read all posts about similar problems I could find both on this forum and others but I'm afraid I still can't figure my problem out. The intake/drain light starts blinking mid way into the dishwashing process. The dish washer fills up, rinses, drains, water is hot, everything seems to function just fine. Some time after the tablet drops from its door mounted container, and the time estimate reaches 46 minutes r


... Dishwashers

My hot point dishwasher is not draining,after all cylces are complete there's always 2 or 3 inches of water on the bottom of the washer, what is causing this? I have a Hotpoint dishwasher 24" built in. The switch won't come on just hums. When I oprn the door ther is 2" of water on the bottom? Any solutions . Where is the reset button on serial number hda430vww, hda400vba> Thank you!


... Dishwashers

Water inflow light comes on midcycle and alarm sounds open and closing door usually solves the problem occasionally dishwasher over flows. Fully intergrated dish wash and no obvious occlusion to water inflow. Dish washer only 2 years of use. Tim Jeffery


Check the outlet waste pipe, if this is partially block it could cause your problem. ... Gaggenau Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2314 seconds