Having problems with your Indesit 24 in. D61 Free-standing Dishwasher ?

Indesit dishwasher sump keeps filling up with water when turned on

\015 When I turn my dishwasher on it just fills the sump up with water instead. can anyone advise me to is wrong. many thanks\015

Answers :

I had a similar problem every time i bailed the sump out by hand and turned the machine back on it would fill the sump or just shut off.
\015\012
\015\012Having spent ages checking various site it boiled down to one of three things there is a thermostat switch underneath they are know to go on the indesits and cost next to nothing to replace
\015\012
\015\012second cause and most probable is to take machine outside before you do this front cover below front door removes to give access to pump you ll know it the pump because it has a pipe rinning into it and one out on my indesit i turned it upside down and got really easy access to it comes of easily take it to pices bit by bit really easy probably need small allun key depends on model check put for foreign objects , spinx blackpool rock etec etc only kidding it might be a bit of plastic or something that stop the spindle turning freely inside the pump if you find anything clean put back and off you go if pump is knackered you can get them off the web for 4.95
\015\012last but not least is the problem that mine actually had in the end and the easiest to fix `water pressure` if there is insufficient water pressure the machine regognised this and activate a shut off valve the machine lights flash you can reset the programme but it still does nt work. take the water pipe off the back put it into a bucket and open the valve you ll now what good pressure looks like mine was poor when i took the adjacent kitchen unit out it transpired a shut off vavle had been placed on the pipework the vavle had never been opened fully by the plumber and was restricting the water supply . take your time dont rush and be methodical take advantage of a local parts supplier ash them what most repairers will do first. it can be very rewarding to find that a/ you can do it and b/youve saved 60 or 70 quid in the process.
\015\012
\015\012ps never mess with the machine whilst connected to the mains or spiky hair might come free with the repair and do take the machine outside or you ll have water evrywhere trust me
Repair Help & Product Troubleshooting for Indesit 24 in. D61 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Indesit dishwasher sump keeps filling up with water when turned on


I had a similar problem every time i bailed the sump out by hand and turned the machine back on it would fill the sump or just shut off.\015\012\015\012Having spent ages checking various site it boiled down to one of three things there is ... Indesit 24 in. D61 Free-standing Dishwasher

Model #363.14232100 dishwasher. When you turn the switch to on, it will not come on. If you keep turning the knob slowly you can hear the dishwasher trying to start up,but it doesn't. Keep turning the knob and its the same thing, sounds like it will start, but it doesn't. It did fill with water, but once it was opened it didn't start up where it left off. The lock switch was in position, and still nothing. Now I have water in the bottom but can't get the thing to come on. Any suggestions? Help!


... Kenmore 24 in. 16539 Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

I have a lx30h dishwasher and the problem is that when i turn it on the first time,normally it should fill the sump and wait to fill after it has reached 166 deg .so whats happening now is that it fills only 2 seconds and tries to heat the water but there is not enough to water so the element gets hot and the high limit does it's job.what do you think of my problem.i have never seen that before good luck and i can't wait to have the answer best regards sylvain ouellet


Hi\015\012\015\012\015\012To correct this make sure the water inlet hose is firmly connected and is not kinked or blocked. Clean the inlet hose and inlet filter (inlet screen). If this doesn't resolve the issue then check the ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Dishwasher fills tub continuously until float turns it off whether in cyle, during drying or after cyle complete. That means during drying when the dishwasher is trying to dry the dishes the tub fills up preventing drying. This is a new dishwasher that I've never used. I allways noticed the tub was full of water, but thought that was just to keep the seals moist so they don't rot. I've been in my house 5 years and only hand washed my dishes because it was more convienient. Now that there ar


Ayacht, the fill is a timed fill controlled by the control board (part number 99003158). The float is a safety device designed to cut power to the valve in the event of a failure. The fact that the float is doing it's job and stopping the fill tend ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

My Bosch dishwasher keeps on filling with water. It won't turn off. I had to turn off the water source to it for the night. Please help. I have a large family and rely on this appliance every day. Thanks!


The problem that you described should be the float switch. It could also be a defective fill valve (stuck open) ... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

My frigidaire dishwasher will not shut off the water being pumped into the dishwasher. It just keeps pumping in even after the required fill time and will not shut off, eventually I have to turn off the shut off so that it doesn't overflow. The float is working ok. Is this a sensor,circuit board?


... Frigidaire Dishwashers

Indesit DV620 HiWhen I turn my indesit dishwasher DV620 on it fills with water for pre-wash with the first button lit and then the first and second buttons flash and nothing else happens!


Check your manual it should tell you what this code means and wether you can deal with it yourself ... Indesit 23 in. DV62 IX Built-in Dishwasher

My ignis intergrated dishwasher keeps turning itself off. It starts fine fills with water, then cuts out turns off then drains.


Does it work on a different cycle ... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

No water is coming thru the water valve to fill the dishwasher. The water is turned on. I had a Kenmore portable dishwasher and we just converted it to a built-in. The electricity is on and the water line installed. When I turn on the dishwasher, it comes on ok but no water is coming into the machine.


Most probable cause a faulty intake solenoid. OK start simple and go from there.If your have power and light etc come on then we know you are good for power. I'll assume that is OK. If\012you are not getting any li ... Dishwashers

My dishwasher keeps filling with water and the water then starts to come out of the bottom of the door. It therefore does not go into any cycle but keeps trying to fill with water but the water keeps coming out of the bottom of the dorr from the inside


... KitchenAid KUDS24SE Built-in Dishwasher

Dishwasher keeps filling with water at the end of the drying cycle even if you turn it off.


Hi and welcome to FixYa, I am Kelly.\015\012 There is a tiny speck of debris that is caught in the diaphragm of the inlet water valve allowing it to bypass water even when off. The Diaphragm is located under the solenoid. Some ... Dishwashers

GE Nautilus M# GSC3400JWW When started, dishwasher does not stop filling up with water up When turned off dishwasher continues to fill up until water is turned off at the faucet. What is wrong with this thing?.


... GE Nautilus 24" Built-in Dishwasher

I have a Baumatic dishwasher and the E4 error message keeps coming back. We empty the water in the base of the unit, check the float triggered switch OK. It works for a while then the error re-occurs as the sump fills up again. What could be the cause?


... Baumatic 23 in. BFD61SS Free-standing Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have an Asko DW 95.2 model 1706 dishwasher that keeps filling with water. Every morning and evening, the whole bottom of the dishwasher fills with water. What is the solution? Do I need to replace the water inlet valve? If so, what is the part number?


... Asko Dishwashers

Whirlpool dishwasher my dishwasher seems to work fine except that it won't fill with water. what do you think is up with it? Will not fill with water??? Ran fine yesterday, went to turn it on today and it will not fill/spray any water.


The very first thing to check is the float inside the tub. Most of them look like a mushroom in one of the front corners. Raise it up and drop it back down. It should move easily and you should hear a slight click as it sets back down. It is common f ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2308 seconds