Having problems with your Indesit 24 in. IDL500 Built-In Dishwasher ?

My dishwasher light comes on but will not run


Answers :

Put some towels dowm and tip the dishwasher over to one side about 45 degrees, if water pours out of the base it means that the dishwasher is in "flood mode" and you have a leak into the base that will need resolving.
Thanks

Repair Help & Product Troubleshooting for Indesit 24 in. IDL500 Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Control panel buttons don't work. Seem to be stuck in the "Lock On" mode. Can't turn off, and dishwasher won't run. When you open the door all lights go off, but as soon as you relatch the door, the "Lock On" light comes on, although sometimes it can be another light. In any case, it won't run.


... Kenmore Dishwashers

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

E4 error light comes on, dishwasher won't run, this apparently means water is on a sensor, have removed water from collection tray in bottom, tilted machine backward to dry out sensor, left for 24 hours, machine still won't run. Currently a very small new counter top but a useless dishwasher.


The problem is related to the floater assembly inside the dishwasher. It is filling up with gunk and stop working properly. I found out the hard way after a good spill. The solution is easy but takes a bit of time.1. Unplug the power and water h ... Danby DDW497W 22 in. Countertop Dishwasher

My KitchenAid KUDI01FL dishwasher will not start. When I run the self test all of the LED lights come on and stay on indefinitey without blinking until I press cancel. Then the cancel light comes on without blinking. What does this mean? Thanks!


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a whirlpool dishwasher Quiet partner 2. I am using cascade detergent, my dishes coming out spotty. I have tried running with a very light load and the same thing happens. I notice that there is a white film around where the water comes out during a wash. I am running a normal cycle with heated dry.


Your problem is hard water. the minerals dry on your glassware causing a white film or residue. go to www.dishwasherfilter.com. they have an awesome product designed for yo ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenmore quietguard 7 dishwasher...clean light flashing, dishwasher won't run repair guy a few weeks ago couldn't come, but told my husband to push a couple of the buttons on the control panel, and it worked for a while... repair guy coming back on Monday, but I''d like to know the buttons to push to reset it so I can use it till then


... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Lock light comes on and dishwasher will not run on water miser cycle


... Kenmore Dishwashers

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you


... Bosch SHX46L1xUC Dishwasher

My Kenwood dishwasher KDW24FI/B has worked fine for approx 2 years. But now when I put my dishwasher on, the cycle never seems to end. After a few hours of running I opened the door to find the tablet hadn't dissolved but lots of steam coming out. I tried 2 more times and the same thing happened. The pump is working and everything seems ok. After reading the manual I have noticed the salt and rinse aid lights are iluminated. I have never put salt or rinse aid in since I had the dishwasher so thi


Lol is it a stereo or a kenmore, dishwashers dont use salt, but water softeners do ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1986 seconds