Having problems with your Indesit Dishwashers ?

Glasses and dishes coming out unclean and smeary have put a cleaner in but no difference part where salt goes in keeps filling up with water


Answers :

Make sure that there is no blockage of the water flow to rotors (i.e. a pot located over a central water spout, misaligned movable water connections).

Next, make sure there is no cutlery or the like that goes through the slide out baskets to stop the rotors from turning.

Also, just give the rotors a spin by hand to make sure they are free to do their job.

Have never heard of a salt being put anywhere in a dishwasher - just in a water softener which is usually not part of a dishwasher.

Repair Help & Product Troubleshooting for Indesit Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Glasses and dishes coming out unclean and smeary have put a cleaner in but no difference part where salt goes in keeps filling up with water


Make sure that there is no blockage of the water flow to rotors (i.e. a pot located over a central water spout, misaligned movable water connections).Next, make sure there is no cutlery or the like that goes through the slide out baskets ... Indesit Dishwashers

GU2700 Whirlpool - Does NOT FILL 2 Gallons on INITAL FILL - unit has new parts FILL VALVE IS NEW OVER FILL SWITCH IS NEW while filling if you reach under the unit and push the over fill float up it turns off the fill cycle - if you let go - unit keeps filling - but does not add the correct 2 gallons - water is not even close to the heating element - does not have enough water to come out of the TOP SPRAY Arm


... Whirlpool Dishwashers

Water softener Salt residue remains on the dishes. The water softener is going throught salt like crazy. I fill the salt and make sure that the light is off before I start the cylce. Within the first 20-45 mins the salt light comes on again and the dishes will not wash properly. We have come to the conclusion that the salt is being distributed to quicky but cannot figure out why the light keeps coming on. The switch inside the cap for the salt is set a the min.


Just a thought, I hope the lady did not use table salt :-) ... Danby 17 in. DDW1802W Designer Series Built-in Dishwasher

We have an Rangemaster RDW459F1 integrated dishwasher and there is a strong taste of salt on everything.We indroduced 2 kg of salt into the dispenser after first filling with water as instructed. We live in a hard water area but even so I turned the arrow more to the - side, but it has not made any difference. It did seem alot of salt to put but it was first time being used. Can you help me please? Jackie


Stop using the tablets. they don't work in hard water areas. I think what you are dealing with is hard water deposits. Use "Lemi shine" for your main wash and the packets for your pre-wash. No one has harder water than where i live... Lemi shine work ... Dishwashers

I have an Asko DW 95.2 model 1706 dishwasher that keeps filling with water. Every morning and evening, the whole bottom of the dishwasher fills with water. What is the solution? Do I need to replace the water inlet valve? If so, what is the part number?


... Asko Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

We have a Whirlpool mod# DU1055XTVD0 dishwasher .. the blue latch designed to keep the lid to the detergent dispenser closed after filling has come loose from the inside door panel and now will not stay in place to keep the detergent lid shut. We did find a small o-ring in the bottom of the tub that apparently is part of what helps maybe hold this latch in place, but obviously there must be something else that fits inside the hole the latch goes in that keeps it secure. This


... Whirlpool Dishwashers

Hi, My dishwasher keeps stopping mid cycle and the door pops open. The soapy water is always gathered in the bottom and there's no way for me to get rid of the water, unless i restart the full cycle. The dishes are all getting stained with white marks, even though the salt and rinse aid is filled. Please help!


Sounds like the latch is worn out you mabe able to get a new one at appliancezone.com.... also check the drain for debris ... Baumatic 23 in. BDW9 Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Nobel stainless dishwasher. water comes in but keeps pumping and does not go into cycle. for example, if we put the washer on towas dishes and leave it over night, in the morning it will still be pumping water into the machine.obviously it does not over fill because i am assuming it goes out the overflow. please help


Lookout the following things:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely rep ... Dishwashers

My dishwasher keeps filling with water and the water then starts to come out of the bottom of the door. It therefore does not go into any cycle but keeps trying to fill with water but the water keeps coming out of the bottom of the dorr from the inside


... KitchenAid KUDS24SE Built-in Dishwasher

The tank where the salt goes should that be filled with water, never used a dishwasher before


Yes it should. Mine is always full of water when I fill it with salt. If there is no water how can the salt dissolve? ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

Carlton Cs1w. Hi I have a Carlton slimline dishwasher. No problem with filling, heating and emptying. But if I set it to full programme it sticks. Starting with pan setting and letting run right through programme it just keeps sticking. On last programme timer moves ok for first 10 or so minutes then gets no further. Tried different settings, checked everything I can think of and cleaned added salt etc. Got given. Last owner only used a few times, moved house and no room for it. But was sitting


... Dishwashers

Grinding The situation: I have had my Whirlpool DU915PWPB1 for 2 1/2 years, it isn't the greatest dishwasher but does the job good enough. Recently, the water will fill, the washing cycle will run but then when that part stops it goes into a whirring that seems like a motor is going but nothing is moving. I have removed the Filter Modual in an attempt to find out what the grinding would be. There doesn't seem to have anything in the way or under the filter. I have ascertained that the grin


Noise probably not from there when reassembled the plate will not be direct contact with screen noise is probably from wash motor itself..suggest checking owners manual for warranty info ... Dishwashers

Hi, I have an ASKO D3250 dishwasher and it keeps stopping during the wash cycle and flashing the heavy pots and pots symbol simultaneously. I tried cleaning the filter basket and found a little plastic part floating in there that has printed on it PP-T20. I don't know where this piece goes or if it's even the culprit. There is a little bit of water not draining from the filter area when I unscrew the outer filter basket, I cleaned it out, but when I re-run it, it still stops and gives the dual f


The part is a cap for the drain pump. You can put it back into position by removing the filters and placing it to the left of where the circular filter would be positioned. The part goes in with the part numbers on the bottom facing down. When posit ... Asko 24 in. D3530FI Built-in Dishwasher

The salt warning light came on (red) and went to put salt in but noticed it was filled with water. I have filled it with salt now and the warning light has gone off but now when I try to select a program it wont. I have drained the water in the salt dispenser but it still wont work! Help!


What is the make and model of the item? ... Dishwashers

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

My Bosch SHX46A dishwasher keeps filling up with water and won't stop. The water just keeps coming up through the bottom. It will drain fine, but after the cancel drain sequence, water just keeps coming up, overflowing the tub onto the floor. I had to shut off the water.


... Bosch Dishwashers

My dishwasher salt container is filled with water, what should i do to get the water out so I can fill up my salt? and does it mean my machine is broken?


... Bosch Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

MY GE WATER SOFTENER QUIT WORKING PROPERLY AFTER 6 MONTHS ,I HAVE HAD SERVICE CALLS AT $150 EACH TO NO AVAIL IT DRAWS SALT BRINE MY WATER HARDNESS IS 17 I HAVE SOFTENER SET TO 22 .I HAVE PRE WATER FILTERS HAVE TRIED DIFFERENT SALTS ALL TO NO AVAIL, NEITHER GE OR HOME DEPOT WANT TO HELP AS NOW I AM OUT OF WARRANTY I HAVE BEEN ILL AND IN THE HOSPITAL (CANCER) THAT'S WHY I HAVE GONE OUT OF THE WARRANTY TIME MODEL GXSF30H PURCHASED 19/02/10


As you have purchased GE water softener and stop working after 6 months,then you need to check it from an expert technician and if he is able to solve this issue,then it good and well, but if this takes more money to repair and not under warranty the ... GE 30000 Grain Water Softener GXSF30H

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1604 seconds