Having problems with your Indesit Dishwashers ?

Indesit IDE 750 Display is showing H20 what is the problem?


Answers :

Repair Help & Product Troubleshooting for Indesit Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Indesit IDE 750 Display is showing H20 what is the problem?


... Indesit Dishwashers

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Indesit dishwasher ide 1005...... not working flashing A10 on the display panel what does this mean???


... Hotpoint Dishwashers

Fixing a float switch problem in indesit ide 750


... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

We have an LG dishwasher model LD-12AW2 that randomly goes into alarm tone & displays "PE" on the display. what is the problem??


... Dishwashers

INDESIT IDE 750


... Indesit Dishwashers

My asko dishwasher(1504) keeps running sometimes, The time will run down to 1 min on the disply and stay there and run on and on until I turn it off. Prior to this another problem occured, when the washer does shut off on it's own, the display will read F1(Falt in the heater), I am wondering if one problem has to do with another. The heater problem I can deal with but not the continueous running.


F1 doesn't mean that it's always the heating element itself, often it \015\012can be the control board relay that has shorted and isn't sending power \015\012to the element. If the element is the faulty part, you'd be looking at \015\012about $250 f ... Dishwashers

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

Bosch dishwaher Model # SHX46A does not display indicator lights and does not function in any mode. There is power to the on/off switch that works and power to the control panel. Other wise the unit is dead. The problem occurs consistantly. I have not tried to fix this problem. Please advise. Thanks, Al


Having same problem, power to outlet, but unit is "dead", no lights, won't turn on. Unit is 6 yrs old and don't want to spend $100 for a repair man to tell me there is no hope....anyone else experience this? ... Bosch Dishwashers

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers

We have a KitchenAid KEBC147KSDS06 24" conv. oven. After putting it through a clean cycle, I tried to preheat it to conv, bake @ 350 deg. The display comes up normally and the fan runs, but after 5 sec. the temp disappears from the display and 'Lo' appears in its place. The conv. fan continues to run but neither upper nor lower element heats. Following a suggestion, I tried to reset the oven by turning off its circuit breaker and powering back up, but it did not correct the problem.


It depends how long you had the self-clean function running. The oven is known to overheat and damage the thermostat during self-clean.\015\012\015\012See postings on some user forums.\015\012\015\012 ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was "I" indicated, or maybe means "1". Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling out the plug from the wall socket, and reconnecting the machine, on the display stays the indication "I" or "1". I can't do anything ...what's the problem


I do not know if you been talking to other experts but without knowing how far you went with them if any I may need to start from the beginning these units are sold in Europe and not the US is that true. Second from your post you went t ... Dishwashers

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

INDESIT IDL505 DISHWASHER(2nd hand working fine for 3 months) started to notice some light/slight streaking, misting especially glasses(annoying but not to much of a problem) then about two weeks later heavy streaking,glasses totally misted completely did have a brief problem with water inlet solenoid but checked it and its working properly (only malfunctioned once) i refilled the salt container and put on a simple wash and found that it used about half the salt in the container,changed the hard


Maybe the machine got a leaked inside.. ... Dishwashers

No lights on the display. Alarm going off ? Changed main board , same problem ...no display alarm keeps going off.


I think there a shorted inside the wiring in your unit,much better call an technician to fine were the wire split or broken. ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0588 seconds