Having problems with your Integra SHX33 Dishwasher ?

Do4esnt clean My Bosch SHX33a05 dishwasher has a problem. It fills and drains well but nothing gets clean. It appears as if the arms are not rotating but the inside is wet when I look inside. I have put a bit on catsup on the inside door and even that is on at the end of the cycle. I have opend and clodes the door multiple times during the cycle and bot arms appear to not be rotating. Nothing is blocking them. I have clean the microfilter, the drain screen and open up the impeller to make sure t


Answers :

Repair Help & Product Troubleshooting for Integra SHX33 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Do4esnt clean My Bosch SHX33a05 dishwasher has a problem. It fills and drains well but nothing gets clean. It appears as if the arms are not rotating but the inside is wet when I look inside. I have put a bit on catsup on the inside door and even that is on at the end of the cycle. I have opend and clodes the door multiple times during the cycle and bot arms appear to not be rotating. Nothing is blocking them. I have clean the microfilter, the drain screen and open up the impeller to make sure t


... Integra SHX33 Dishwasher

I haave dishwasher model 665.743893. The top dishes do not come clean and I suspect that the top arm is not rotating because it is in the exact same position each time I open the door and at the end of the cycle. I took it off to remove possible debris but found none, though difficult to look inside. Do you have any suggestions?


If you can use a high-pressure washer or air hose to blow it out, that would be helpful. Otherwise soak in hot dishwater. Do check the hose to the arm and make sure that is not blocked as well. ... Kenmore Dishwashers

I have a Frigidaire dishwasher, FDB-1100RHC, that is not cleaning dishes. My fiance cleaned the trap at the bottom of the washer, removing both the small basket and the larger mesh grid. After replacing both, the washer doesn't seem to have enough water pressure to spin the lower and/or upper arms. If I interrupt a cycle and open the door, water is dribbling out of the upper arms, but they are not rotating and do not move from whatever position you place them in. Both arms are completely uno


Hello :)don't feel bad, I run into this kind of problem at least once a week.\015\012It does sound like the pressure isn't there so you're not getting water to the upper spray arm. What you need to do is take the pump apart, which i ... Frigidaire Dishwashers

The tablet is still still in the door when the cycle has finished. It is wet and part disolved and the litle door has opened. I have checked the rinse aid and salt and cleaned the spray arms but they were clear. I always check nothing is in the way of the arms spinning. Any suggestons?


It actually sounds like maybe the packet is getting partially melted to the inside. Have you tried washing with no heat at all? Or maybe change brands on detergent packets. The main thing is your door is actually opening all the way, if so, then the ... Bosch Dishwashers

GLD5900N00WW I have noticed that my dishes in the upper racks are not getting clean. I emptied the dishwasher and ran it without dishes. I noticed (when I opened the door mid cycle) that the bottom arm is rotating but the upper arm does not appear to be rotating. Any ideas why this is and how I might be able to fix it?


You need to remove the top wash arm and check for any blockages in the holes, clean them out and make sure the arm spins freely. ... Dishwashers

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

DISHES ARE NOT COMING CLEAN BYPASSED THE DOOR LATCH TO WATCH CYCLES,LOOKS LIKE THERE IS NOT ENOUGH WATER PRESSURE TO ACTIVATE THE WATER TOWER AND ROTATING ARM?WATER PUMPS OUT BUT NOT ENOUGH TO MAKE THINGS MOVE?


I had the same problem and fixed it by disassembling the lower spray arm and return filter, and cleaning all the junk out.\015\012Most dishwashers have 'risers' that bring the water up to the top\015\012sprayer or arm located under the top rack ... Dishwashers

It acts like it is washing and it will start I can hear water going into the dishwasher then it just stops after a min or so. Then it just sits there and does nothing when the cycle is finished the detergent really hasn't been used it is just smeared on the inside of the door and the dishes are not clean


Hi,\015\012\015\012can you hear it draining? it will start hissing at the aerator at the sink, hopefully you have an aerator-its a small usually chrome cylinder thing next to the faucet, check this, remove the top of the aerator by pulling it s ... Dishwashers

Dishes don't get clean. soap still on inside of door. . . water coming up to fill line and hot enough and dishwasher drains after cycle, spray arms are clear. . . help!


Water from the wash arms must be able to reach the detergent cup during the wash. It sounds as though the machine may be over-loaded during the wash and water does not cause the detergent to mix with the wash tank water. Try washing a cycle with noth ... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

After running a cycle, there is some water in the tub and the soap dispenser is open but the soap has only run down the inside of the door. It does not sound like there is a vigorous spray during the wash cycle. Opening the door during the wash cycle reveals only a little water reaching the upper arm.


May have a stripped wash impeller. I would tear into the pump and look for any kind of obstruction but if its clean probably the motor assembly needs replacing. ... Frigidaire Dishwashers

Siemens integrated dishwasher not cleaning dishes properly anymore and tablet not dissolving anymore, going through cycle perfectly normal, both upper and lower rotating arm working perfectly, salt in screwcap area, very hot as usual at end of cycle, unless dishes go in cleaned, they wont come out clean, any ideas please ?


I have exactly the same problem - did you work out what the issue was & how did you resolve it? Rob ... Siemens 24 in. SE64A630GB Built-In Dishwasher

I have a Whirlpool Quiet Partner I (DU920PWKQ0) that the detergent dispenser door is not opening to allow the detergent out during the cleaning cycle. So, the dishes are not being properly cleaned. I do not regularly run a dishwasher cleaner through the dishwasher like some sites recommend. Is this problem more related to cleaning than mechanical ..... If it is a mechanical problem, can I take the door plate off the inside of the dishwasher and get parts if needed??? without a service vist? Than


... Whirlpool Dishwashers

Dishes on top rack are not getting clean. the spray arm does rotate when I spin it by hand, but not sure it is spinning when door is closed. Water is present on the spray arm when I open the door to check. Can you suggest things I might check or tell me what may be occurring?


Remove the spray arm and clean each nozzle then fixed it back and test but be sure that the wash pump is working. ... KitchenAid Dishwashers

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

Hello, Im trying to diagnose poor cleaning of glasses in the top rack of my Fridigaire FDB751SCB0. everything seems to work fine but while testing I noticed the upper arm isn't spinning. the lower arm is. i believe the pump is working as water is spayed everywhere inside but no matter which position I leave the upper arm in, I find it in the same place when I open the door. what could cause the upper arm to not get water preventing it from spining?


Hello; first thing to check, which you don't mention, is which side of the glasses aren't coming clean; the outside, which would be caused by the TOP spray not working properly, or the INSIDE, which would be caused by the spray BELOW the top rack not ... Dishwashers

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

I have a Bosch SHX98M dishwasher and the top arm will not rotate. I can see water coming out of the holes when open during a cycle and I have made sure there are no obstruction for the arm or anything stuck in the arm feed line. I just had a technician here who was at a loss and did not think the pump was bad since alot of water is being pushed around inside. The bottom arm works fine.


... Dishwashers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

The spray arms do not seem to be rotating. The dishes are not getting clean and even though we had the spray devices cleaned by a service tech and just ran a full wash cycle with vinegar, the soap dispenser isn't fully cleaned of soap and the dirtiest of the dishes are still soiled.


Probably the pump is bad ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1762 seconds