Having problems with your Jackson 24 in. JPX-300H Built-in Dishwasher ?

Model JPX-300H, the unit does not fill, but it will drain if you fill with water from a bucket. Also when the unit drains there is water coming from under the unit. How do I check the fill valve for proper operation. Thanks


Answers :

The fill valve is easy just take the coil off and there is a hole in it put a metel screwdriver in the hole and turn the unit on if it pulls the screwdriver like a mganet it works is more likely i bad diaphram now as for the draining it drains bu turning a valve dirverting the watter from the pump down the drain hose so you must have a hole or leak in the hose
Repair Help & Product Troubleshooting for Jackson 24 in. JPX-300H Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model JPX-300H, the unit does not fill, but it will drain if you fill with water from a bucket. Also when the unit drains there is water coming from under the unit. How do I check the fill valve for proper operation. Thanks


The fill valve is easy just take the coil off and there is a hole in it put a metel screwdriver in the hole and turn the unit on if it pulls the screwdriver like a mganet it works is more likely i bad diaphram now as for the draining it drains bu ... Jackson 24 in. JPX-300H Built-in Dishwasher

Cycles improperly My dishwasher does not cycle properly. It races through the cycles, even when set to pots & pans, in about ten minutes. At first I thought it not filling properly, checked the fill switch, it's fine and water does come in. Then when it's finished it does not always drain completely. I have checked everything on the drain end as well. It seems to have a mind of it's own. I replaced the $145 computer control with no luck. It actually sped up from the original 16 minute ful


Hi there,\015\012\015\012please let me know the make and full model # off your d/w.\015\012\015\012thanks ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

MAYTAG MDBH979AWS DOES NOT SEEM TO FILL WITH WATER, AND HAS STOPPED CLEANING THE DISHES..My husband took everything apart and we cleaned each piece and put it back together , there was no indication that anything was clogged, and he was able to determine that water was coming in to the washer, but dishes are still dirty. There seems to be soap residue on the bottom of the tub. We also check to see if it was draining properly and that was fine also. Any other suggestions?


... GE Dishwashers

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Miele dishwasher model# g868 could be 4 or u at end, customer complained water not coming into d/w ,when i got there water was coming in.for a few minutes then stopped filling ,drains fine, customer had not operated machine for a few days.i disconected the safety valve hose from under sink to see if water comes through does not when advancing cycle by hand, washes ok when water came in, thanks, Murray


... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

I have a Frigidaire dishwasher. Model FDB520RHS0, Serial TH92539147. The drum fills with water but will not drain. I purchased the unit about 2 years ago. It has been used sparingly and mostly on light wash. I removed the basket and could find nothing blocking the drain. Is there a fix? Can I replace the drain pump? The unit is making a noise as if it is trying to drain but nothing is happening. I have checked the drain line for clogs and it is clear and the terminal end is conn


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Kenmore Elite dishwasher (2004) and recently it has been leaking internally at a very slow pace. When not in use it will slowly fill until the floor of the unit is filled and then leak onto the kitchen floor unless we press the drain button and then it drains completely. The water seems to be coming from the front of the washer, potentially from the door itself. The amount of leakage is barely discernible but will fill over the course of a 24 hour period. The dishwasher otherwise wo


Hello,\015\012The water is admitted into the dishwasher through a little magnetically controlled valve underneath your dishwasher. This valve opens and shuts electrically. There is a little plunger in it that is pushed shut by a spring when no ... Kenmore Dishwashers

Hi, I have a Neff S5457XOGB dish washer. The unit is programmed to start - but the pump just keeps empying water, even when the door is open. After approx 5 mins this can stop and thedishwasher enters its normal cycle - however there is no water. I have checked and clean the pump assembly I have filled the base with water - and the pump successfully empties the into the drain I have checked the filter that conects directly to the cold feed. - Any advice please? Many thanks.


... Neff 24 in. S5457X0GB Built-in Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

Our G1140 SC starts with the drain pump running and then after draining all three amber lights come on and stay on and the dishwasher does not fill with water. I have checked the water supply which is on and connected.


... Miele Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

My dishwasher (Optima G2420) had an error F13 for sometime. By turning it off and restarding it would work. But now drain/intake light flashes and nothing is happening. We have checked the triple filter, the filter where water comes in ect. It drains the water but it appears that it cannot take water in. There is a white unit that the intake water goes in and I think that might be the proble.


... Miele Optima G2420SCi Stainless Steel Builtin Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

Upper spray arm is not turning round even though water is coming through. We have checked the internal system for blockages and the machine is filling / draining as normal. When a full programme is run, many of the dishes, particularly on the top shelf, are dirty and many have hardly been touched by water. Could a pump or other part be faulty?


I found the problem to be neither blockages of the upper arm or roof spray arm or the upper basket arm hitting the the back of the dishwasher. the problem was that the pump inlet where the food scraps are macerated was blocked with all manner of gung ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1928 seconds