Having problems with your Jackson JP-24B Built-in Dishwasher ?

We have jp-24B series dishwasher it was doing great until about 2 months ago and the glasses come out all spotty. The dishwasher seems to be running through all the cycles and it gets up to temperature but the glasses have all thses lines when the water drains out of the glasses and spots, a light chaulky color. We have ran the dishes for 2 or 3 cycles and it helps a little bit. What is the problem?


Answers :

The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your dishwasher and removes the hard minerals that cause these spots. Very affordable and guaranteed to leave your dishes looking amazing every time.
Repair Help & Product Troubleshooting for Jackson JP-24B Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have jp-24B series dishwasher it was doing great until about 2 months ago and the glasses come out all spotty. The dishwasher seems to be running through all the cycles and it gets up to temperature but the glasses have all thses lines when the water drains out of the glasses and spots, a light chaulky color. We have ran the dishes for 2 or 3 cycles and it helps a little bit. What is the problem?


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Jackson JP-24B Built-in Dishwasher

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

Glasses int he top rack of my kitchenaid dishwasher don;t get clean. they finish the run spotted and covered in what looks like baked on dirty dishwater. dishes in the lower rack look ok, but the silverware is always dirty, too. i figure it's one of two things - either the top sprayer isn't working, or the machines doesn't drain the dirty water well enough. or maybe it's something else - cycle regulator? the machine is about 4 years old. thanks


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is to add some vinegar to the bo ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

First we had drain issue with Bosch Integra® 500 SHX55M05UC Built-in Dishwasher ECO cycle. It stopped after a while. I thought it may be because last cycle might not be finished well. When we ran again ECO cycle with no drain issues but cycle did not finished as it used to be. I am sure because cycle countdown were not zero and because infra red light was off which is sing of complete cycle.


... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers

Not draining caloric dishwasher is not draining...was working fine before i stopped it mid cycle to take out a glass...then the next time i used it i put it on the pots and pan cycle and after it dialed to off i opened up and found a "block" of detergent and it hadnt drained... i just put it back on the normal cycle and am trying again... we'll see ?


Does the motor come on when it is supposed to drain? If it does then by stopping the unit mid cycle you could have had a freak instance of food particulate blocking the air gap located on the back of your kitchen sink (if you have one) It would loo ... Caloric 24 in. CDU210C Built-in Dishwasher

Maytag dishwasher The dishwasher goes through the first wash cycle on a light setting and first two on a normal cycle but will not continue.The motor hums but does nothing else.It drains fine as well after the wash cycle.


Hi kimleh.\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your question is: The dishwasher goes through the first wash cycle on a light setting and first two on a normal cycle but will not continue.The motor hum ... Maytag Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

We have a 2003 KitchenAid KUDI01IL Dishwasher that will not start . We had problems with the top rack dishes getting clean and we replaced the chopper. The dishwasher worked fine for one cycle, but now will not start. The buttons have lights except for the high temp scrub light. The dishwasher will drain when cancel is hit but that is it.


... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

Hello .i have a dish washer model du1010xtxq1.this is a brand new dishwasher. when i select the cycle it starts. and it runs for approx 8 min then it goes into drain cycle the red light goes on . then it drains when is finishn drainning it will shutt off. what can i do? i need help


We are having the same problem. Did you find out anything to help? ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Intake drain The dishwasher is an excellent machine but the intake drain problem is driving us crazy. I have had pumps changed twice and that has not been the problem. I start the dishwash and within a minute the intake drain light comes on right after the first cycle. I need help!!


... Miele 24 in. Touchtronic Platinum Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2346 seconds