Having problems with your Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher ?

The only button that is working is "quick wash" - when I push the other ones nothing happens


Answers :

Repair Help & Product Troubleshooting for Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The only button that is working is "quick wash" - when I push the other ones nothing happens


... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

Hello I'm looking for advise on my 11 year old dishwasher. It's a kenmore ultra wash model # 15812. The problem is that when you push the wash button nothing happens. The drain funtion still works and all the lights on the front panel work but no water is flowimg into the washer. Do I try to fix this or just buy a new one?


Hello there:To be honest with you i would first try these solutions and see if they work cause a new machine would cost a lot of money.But if you can fix yours it would cost a lot less so plese try these solutions that i have provid ... Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Hi, I've got a dw 681es wh nemo dishwasher. I turn it on, it starts working but it sounds funny....and nothing happens. after a while the start/reset button flashes and then it doesnt continue. Any clues? I start it on the quick wash cycle but it quickly flicks to the rinse cycle when this problem occurs. I used to just reset and it worked again but now it just wont work.


... Fisher and Paykel Dishwashers

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

Control panel is locked. no buttons work when pushed. door panel says to push and hold ''heat dry'' button for 4 seconds to clear. nothing happens. this is on kenmore ultra wash dishwasher


Try unplugging the machine and wait 5 minutes. Plug it back in, the problem should clear. ... Dishwashers

I have a Bosch SHE6AP05UC dishwasher. All of a sudden when I turned it on to wash a load the clean light and the quick wash light came on and when you push the wash button nothing happens. When you turn it off and on those 2 lights come on solid and you can't wash. How can I reset or what can I do to troubleshoot this?


... Bosch SHE6AP05UC 24 in Builtin Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Bosch SHE43F02UC/50 Lights on, but won't start any cycle....Regular Wash light only one on with timer showing 188.....pushing other buttons does nothing.....no noise, no water fill, just those two light remain on and nothing happens?


... Bosch Dishwashers

Hi, I have a Fisher and Paykel DD603 dishwasher. The bottom drawer works fine but the top drawer doesnt work at all. It appears normal until the start button is pushed and then I get 3 very quick beeps followed but a 4th slightly longer beep. Then nothing happens, any ideas or help would be much appreciated. Thanks Neville.


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

I have a Frigidaire dishwasher, Model # FDB1050REB2, Serial # TH74114244. I push the start/cancel button and the washing lite just blinks, and nothing happens. There is also 1-2 inches of water at the bottom of the dishwasher. What can I do. I installed the dishwasher myself. It worked fine up to this point.


Sounds like the control panel has failed . but ck the drain pump for a plug . if it cant drain the the prosser knows and the flashing is the trouble code .. mm ... Dishwashers

I have the maytag dishwasher series 300 MDBH975AWW and my control panel have stopped working, I push on the washcycle button and nothing happens it will not rinse, it will not wash. What can I do to fix this?


... Maytag 24 in. MDB9750AW Dishwasher

When I push the start button on my dish washer, nothing happens. Part of the problem is, is that I never use it, but I don't want it not to work. It was like new when I moved here two years ago, but I don't have enough dishes to wash in it, so it sits all time.


A dishwasher is like a car and needs to be used once in a while. If you put your car in the garage and don't try to start it for a year, chances are, it will not start. A dishwasher should have at least some water in the pump to prevent the seals f ... GE Nautilus 24" Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

I own a Maytag MDB5100AWB three lights are flashing on the panel, the clean button, rinse only and heavy wash. I've tried turning off the breaker for 20 minutes, pushing the buttons in sequence, holding them down, nothing seems to work. It's done this before and a repairman pushed the buttons and it worked. Is there anything I can do to avoid another service call?


... Dishwashers

The dishwasher won't turn on to wash dishes when any buttons are pushed (quick wash, normal etc). However, other lights and buuttons work (drain, 1-2-3 buttons all light up). The door is closed and latches. Any ideas what I can do to make it work?


Probably the touch pad or may be called user interface. ... Whirlpool Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

When I push the start button nothing happens, all the other buttons work


... Whirlpool MDBH979AWB Builtin Dishwasher

Dishwasher control buttons do not work. Machine is stuck on low wash and headed dry. Pushing butttons on crontrol panel do nothing. Dishwasher seems to work, fills with water , you can here it run it's water agitation, and drains, but only works in low wash


Hello,This means the touch pad has failed, you can make this repair it's simple. Try flipping the breaker off for several minutes this may reset the glitch.Applian ... Dishwashers

My frigidaire dishwasher (FFBD2405KB) is not working... when I press the wash button, it will blink, but nothing happens. I've tried it on all settings, but nothing works. It's obviously getting power since the lights are working. I've cleaned the drain thoroughly and made sure there were no obstructions. Any ideas?


... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1638 seconds