Having problems with your Jenn-Air 24 in. JDB1080AW Built-in Dishwasher ?

The operations touch pad is not working properly. It does not illuminate and when I select a washing cycle is does not activate.


Answers :

Repair Help & Product Troubleshooting for Jenn-Air 24 in. JDB1080AW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The operations touch pad is not working properly. It does not illuminate and when I select a washing cycle is does not activate.


... Jenn-Air 24 in. JDB1080AW Built-in Dishwasher

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -


... Kenmore Dishwashers

Amana model ADB1500AWW, start/cancel touch pad does not work...power to unit...wash cycles can be selected. Could it possibly be a door switch?..touch pad or circuit board?


... Amana Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or


Ya id say until u open the door after it has washed ... Bosch Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

Cannot operate touch control pad - Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher


Hi,Your control pad has gone bad and you will need to replace it... it is easy to replace, just make sure to mark your wires before removing so you can get them back where they belong...\012How to Buy ... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Touch pad to select wash function at top of door not coming on when pushed


... Jenn-Air 24 in. JDB4950 Built-in Dishwasher

Cannot select any wash cycle but quick wash. No other wash cycles will light up when selected. If you select the start button, the quick wash lights and the dishwasher starts (even with door open).


I had this same problem and being an electrical engineer, I decided to see what I could fix before replacing the board. The symptoms were the only cycle I could run was the QUICK WASH - no other cycle buttons responded.\015\012\015\012I took t ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

Du1100xtpq7 has had the touch pad replaced along with the circuit board that goes behind it and yet it just keeps repeating the wash cycle and goes for hours


\015\012Hi,\015\012\015\012\015\012\015\012\015\012The basic reason for longer wash cycle is due to more time taken for the temperature to reach the adequate temperature. The sensor keeps going into new cycles till it finds the wate ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

The start button on touch pad does not light and start the wash cycle


... Maytag 24 in. MDBH940AW Built-in Dishwasher

Touch pad to switch wash cycles is not working


The touch pad is bad ... Dishwashers

AMANA ADB1500AWQ Control buttons not working properly. Will not allow selection of wash cycle or heated dry. Occasionally the controls are completely dead, and none of the lights light up. This dishwasher is only 18 months old!


Unplug the power cable from wall socket.check the voltage from the household receptacle to the dishwasher, volt meter.It might be your neutral line is bad,or the console is bad ... Amana Dishwashers

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Indesit idl 535, washing on usual cycle but not heating and dishes not being cleand properly? Disolves tablet and goes through full wash cycle as usual but doesnt wash dishes properly and the dryer isn't working as it normally is hot when you open the door, but it is just cold. water draining as normal too.


Your problem is very clear, you need to replace the wash tank heating element. ... Indesit 24 in. IDL500 Built-In Dishwasher

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1041 seconds