Having problems with your Jenn-Air 24 in. JDB8910 Built-in Dishwasher ?

Not enough water to wash dishes and machine keeps filling

\015 This is a 9 year old dishwasher in a house with problem limescale. I hear hardly any water when it is running and the dishes are gritty when finished. Now the water continues to trickle into the machine when it is not running and must be shut off at the valve between uses. If this is a problem with the inlet valve, is it worth the cost having it replaced on a dishwasher of this age? Any suggestions other than a conventional water softener for limescale problems? We have replaced three coils in our boiler. Thank you for your help.\015

Answers :

The " inlet valve" as you call it is very cheap $20.00 at right store! easy fix
Repair Help & Product Troubleshooting for Jenn-Air 24 in. JDB8910 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not enough water to wash dishes and machine keeps filling


The " inlet valve" as you call it is very cheap $20.00 at right store! easy fix ... Jenn-Air 24 in. JDB8910 Built-in Dishwasher

I have a Kitchen Aid Superba KUDS24SEBS1. The inlet water pressure is good and the dishwasher fills and starts the wash cycle, however, after the initial spray of water, it seems that all of the water drains out and there is nothing left to continue the cycle and wash the dishes. It's like it's not able to fill up enough to wash the dishes.


When "full" of water, the normal height of level is about 1/2 below the heater assy(large blackish grey coil below he spray arm).. if theres enough water in the unit nad its still not "spraying",its quite possible that your filter/chopper assy is cl ... Dishwashers

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

I have the Siemens SL84A305UC Dishwasher. All of a sudden it stopped cleaning dishes, but everything sounds normal and it fills and drains water, and sounds like it is completing the cycle. In the past when I opened the door while it was actively washing the water would spray out aggressively. Now, when I opened it while it was supposed to be washing I see just a small amount of water coming from the bottom wash blade, and not even enough to turn the blade very far. I thought it was just a c


... Siemens 24 in. SL84A305UC Built-in Dishwasher

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

My kenmore washing machine fills with water but will not wash..it sounds like its doing something then it stops after a while i hear it drain and then stops again..water doesnt spray..I let the dishwasher run for a while but dishes werent even wet


Often these work by reversing the motor which has two pump impellers. One direction will pump the water out and the other will pump it through the spray bar. IF the one pump impeller has broken then that would explain your symptoms. \015\012 ... Kenmore 24 in. 16193 Stainless Steel Built-in Dishwasher

Machine will fill with water but will not spin the water to wash the dishes. machine does drain though.


... Whirlpool GU1200XTKS Dishwasher

Dishwasher fills tub continuously until float turns it off whether in cyle, during drying or after cyle complete. That means during drying when the dishwasher is trying to dry the dishes the tub fills up preventing drying. This is a new dishwasher that I've never used. I allways noticed the tub was full of water, but thought that was just to keep the seals moist so they don't rot. I've been in my house 5 years and only hand washed my dishes because it was more convienient. Now that there ar


Ayacht, the fill is a timed fill controlled by the control board (part number 99003158). The float is a safety device designed to cut power to the valve in the event of a failure. The fact that the float is doing it's job and stopping the fill tend ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

Water softener Salt residue remains on the dishes. The water softener is going throught salt like crazy. I fill the salt and make sure that the light is off before I start the cylce. Within the first 20-45 mins the salt light comes on again and the dishes will not wash properly. We have come to the conclusion that the salt is being distributed to quicky but cannot figure out why the light keeps coming on. The switch inside the cap for the salt is set a the min.


Just a thought, I hope the lady did not use table salt :-) ... Danby 17 in. DDW1802W Designer Series Built-in Dishwasher

My kitchenaid KUDI01DL dishwasher began making a lot of noise while running, then subsequently decided not to circulate the water around to wash the dishes. It sounds like the motor is running (maybe) but there is no washing action going on. The machine will fill, drain and heat the water but nothing else. Is it likely that the pump/motor assembly has ceased to function properly? thanks...


The problem is very likely in the chopper and/or somewhat possible in the impeller. The chopper is replaceable from the front. Disassemble the pump, the chopper will be on its left side under a cover. That cover is kinda tricky to remove (remove all ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Dishwasher just started not filling enough water to wash dishes.


It does sound like a circuit board problem but lets not rush out and pay an exorbitant service fee yet...I checked the user manual and this model does have a timer also...so often timer go out and many people think the problem lies elsewhere...but wh ... GE 24 in. GSD6660GSS Built-in Dishwasher

My ge dishwasher fills with water just fine,cycle starts, but soon after, starts draining some of the water while washing. It then seems like there is not enough water in there to get the dishes clean. Why is it doing this?


... GE PDW8680NSS Built-in Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

My dishwasher fills and runs but the water does not drain out of the machine and I have dirty water that then mixes with clean water to rinse the washed dishes and stays in the bottem.


There is a drain hose for your dishwasher that often gets clogged. Remove the drain hose and clean it out. reinstall the hose and your dishwasher will drain. The dishwasher should have a panel to remove and then comes out easily, just be careful not ... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

My Neff S5443X2 built in dishwasher is not washing my dishes properly. I don't think enough water in getting into the machine as the dishwasher tablet is whole at the end out the wash cycle usually stuck to something. What should I do? Do I need a part replacing by a plumber or can I fix it?


I left the dishwasher off all night then prest the reset button and it worked ... Neff 24 in. S5443X2 Built-in Dishwasher

Dish washer will not wash. Machine will go through all cycles in about 5 minutes. will fill very little water, but wii pump out the water


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Sunbeam SNB542UCAS Built-in Dishwasher

The dish washer will not fill. It starts to , but the float switch apears to be stuck. It runs thru all of the cycles, there is not enough water to wash the dishes.


... Kenmore 24 in. 17669 Free-standing Dishwasher

I have a three-year-old Sears Kenmore Elite dishwasher. I find that despite the fact that we scrape and rinse our dishes before loading the machine, after each three months of use (two loads a day) or so, I have to take the machine apart (spray tower, racks, bottom impeller, bottom screen housing, food grinder cover) and clean-out the food grinder area, for it fills-up with sludge. The sludge restricts the water flow and there isn't enough flow to turn the impellers via that steering jets.


Have you tried different detergents? Some detergents after getting wet and going through the wash cycle with the debris from the wash turns into a grease substance that grimes up in some dishwashers. Try running the machine with hot water this someti ... Dishwashers

Whirlpool ADP 5966 Dishwasher using the complete salt load in 6 washes and coating all the dishes in salt that would not rinse off. I filled the salt and 6 washes later it was requiring a new load of salt. We have had the machine for 5 years no trouble The problem is a complete overload of salt coating everything in the rinse water and drying on during the heated drying cycle. The problem is not caused by the following Cracked of failed seals on the lid to salt compartment N


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2002 seconds