Having problems with your Jenn-Air Dishwashers ?

My Jenn-Air Dishwasher (JDB12070AWF) the heating element won't shut off it just keeps staying hot. I unplugged it but it melted 3 cutting boards and now I am afraid to plug it back in. What do I do to fix this?


Answers :

Repair Help & Product Troubleshooting for Jenn-Air Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Jenn-Air Dishwasher (JDB12070AWF) the heating element won't shut off it just keeps staying hot. I unplugged it but it melted 3 cutting boards and now I am afraid to plug it back in. What do I do to fix this?


... Jenn-Air Dishwashers

The control board is not working. this happened after i took the inside panel off to fix the latch. i took the panel off again to see if anything came unplugged and nothign is unplugged or loose. i checked the outlet i am plugged into and its hot. is there a reset?


Hello there:normally if you unplug the appliance for 10 to 20 minutes this will allow for it to reset it'self internally than plug it in and try it again But if the appliance was plugged in when you tried to reconnect the contro ... Jenn-Air JDB1250AWR Built-in Dishwasher

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standa ... Kenmore 24 in. 16539 Built-in Dishwasher

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Westinghouse Silhouette 906 dishwasher cuts out after pre-wash, sometimes goes through cycle to rinse, then cuts out. Obtained service from sole dishwasher technician in Ballarat - he was very discourteous, claimed to have corrected fault, charged $125.00. Fault not fixed - that was many months ago but don't want him back. Please advise


... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Hi i have a problem with my bosch dishwasher model no.5600 061 333 en(8311), there is no power light and not functioning with any mode and when plugged in it makes a big flash sound from underneath. The plug fuse is still intact. The plug has also melted the plastic backing plate when plugged in. Could you tell me what the problem is and how to go about fixing it. Thankyou.


... Dishwashers

ASKO 1595 Dear greendude, thank you for your reply! i haven't checked the solution yet but wanted to specify: i've got ASKO 1595 and have had it for 4 years. recent year it started to mulfunction: sometimes it would stop in the middle of draining cycle and fault light would flash. this could be normally fixed by unpluging power cord, waitng for a few minutes and pluging power back again. wahat happened now is the different: dishwasher came on on its own, nowbody started it. it came on (draining


Yes have you tried what i suggested yet ... Asko D1776 Stainless Steel Built-in Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

I have full power to the washer, but as soon as i hit start to begin the cycle, i lose all power. i then have to unplug it and then plug it in again and then i get power back agin. as soon as i hit start again i lose all power to washer again. im thinking maybe the mother board is shot????


... EuroTech 24 in. EDW154E Built-in Dishwasher

KitchenAid control board melt down


... KitchenAid Dishwashers

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?


The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Global 300 KA dishlex dishwasher shorts out power board cuts out straight away


... Dishwashers

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Mod m.d.c.5100aww ser28126829ax I had a repairman come out. He said the "sprayers" are plugged. I'm on a fixed income. With my bills I can't afford to get it fixed. Trying to fix it myself. I have the bottom sprayer unsnapped & can't get it back on. Thank you Don


Most dishwashers dispense the detergent via gravity and the sprayer\015\012arms spraying against the soap dispenser once the little door flips\015\012open during the wash cycle. Since it sounds like the soap door is\015\012opening I would look at the ... Dishwashers

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

Leaking my hobart dishwash is leaking. I have taken the back panel off & there is a plastic water tank at the back - it keeps overflowing! How do I fix it? Please help.


... Hobart LXIC-6 Dishwasher

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

I have a KitchenAid drawer dishwasher model kudd01dppa and it has a mind of its own starting and stopping in the middle of the night/day and chiming all different beeps and sounds like its computer is glitching out. We had a service person out and they changed the main computer board and it seemed to fix it for a few days then started again. They gave up. They also tried some sort of reset or reboot but nothing has fixed this intermitten but long term problem. Any ideas?


"it seemed to fix it for a few days then started again" (sic) OK, well if this is so, then in my experience you are getting some, sort of Power Bourne Spike, Surge, or Transient, problem. If there is nothing else it can possibly be. Use a Pow ... Dishwashers

Mod. mdc5100aww ser. 28126829ax purchase date dec. 02 i called the serviceman he said the sprayers are pluged. i'm on a fixed income. with food house payment medicine dr. bills. i can't afford to get it fixed. i tried to get the bottom sprayer off. i could not get it off. now i have it unsnapped & can't get it back together. if you can help me i would appreciate it!!!!!!


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0934 seconds