Having problems with your John Deere 020297 Gas Pressure Washer ?

Wand pressure lost

\015 I WAS WASHING MY HOUSE AND HAD GREAT WATER PRESSURE COMING OUT OF WAND BUT THEN I LOST THE PRESSURE FROM THE WAND. I HAVE CHECKED WATER SUPPLY ITS GOOD CHECKED TO SEE IF SCREEN WERE STOPPED UP AND ENDS BUT THEY WERE NOT , WHAT ELSE COULD I CHECK ? AND CAN YOU TELL ME WHERE THE UNLOADER VALVE IS?\015

Answers :

Repair Help & Product Troubleshooting for John Deere 020297 Gas Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wand pressure lost


... John Deere 020297 Gas Pressure Washer

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a power washer that needs a wand for the high pressure, the low pressure wand is part number PA6630GF. I need the part number and where tp urchase the high pressure wand.


... McCulloch FHH18A Electric Pressure Washer

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

No pressure to the wand. Motor runs and pressure gauge reads 4000 psi.Feels like no power in the wand Is a Honda pressure washer model #BEEX-2965HWCOMX.


... Honda Pressure Washers

My karcher pressure washer is switching on and off when the wand is not being used. the pressure should hold but it appears to cut in and out every 2 secs. the machine works o.k. when pulling the wand trigger but i think the pressure is slightly reduced.


Unfortunately these little units have this problem commonly, 9 times out of 10 it will be the plastic head on the unit will be cracked and leaking slightly... it builds up pressure then leaks out and tries to build up the pressure again ... Karcher K2.26 Electric Power Washer

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

Lost pressure Have honda excell 3200 psi washer. Was using it for about 5 minutes and it lost pressure. Has been working great to this point.


Try this dissconect hose and lance , and check for water flow through the machine , if theres none or just a trickle then you may have gunk in your inlet filter ( usually a small plastic gauze insert just where the water feed hose connects ) ... Honda Pressure Washer PSI 3000

Husky 500 2200 psi. starts and runs ok, but no pressure through the wand. hooked up garden hose to power washer turned water on and it comes through the hose ok, but start up and put wand on and no pressure.


... Pressure Washers

I have the Karcher 2400 psi, 5.0 Honda engine. Starts fine, but when you pull the handle on the spray wand, the pump does not kick in and the water just continues to trickle out of the end of the wand at regular faucet pressure. Occasionally the "clutch" will kick in and you have full pressure, but if it does and I let off of the trigger then chances are that it won't kick in again. has been getting worse for several years.


... Karcher 2500 PSI Pressure Washer

My pressure washer doesn't start/work when I attach my wand to the trigger. It works fine when I take it off, but there is no pressure, just normal water coming out. I'm thinking I may need a replacement wand?


... McCulloch FH160G Pressure Washer

Pressure washer lost pressure in the middle of a job


The pressure valve has stuck in the high pressure position. This prevents anymore inflow and hence no further water will be pumped. \015\012\015\012Rebuild the valve... There are O Rings to replace and clean the bore with croocus cloth. ... Honda Pressure Washer PSI 3000

Troy Bilt pressure washer 2600psi. Engines running fine with supply line, wand, and pressure line hooked up but no water or pressure is coming from pump. pressure line is limp. What is the problem?


... Troy-Bilt Pressure Washers

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

I have a XR 2600 Honda pressure washer. After using it for about an hour, the pressure dropped drastically. I turned it off. I started the following day to finish the job and the pressure was a steady "stream" coming out of the wand - no pressure to clean the concrete. Can you tell me what might be wrong?


Change the spark plug. ... Honda Pressure Washers

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?


Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

Husky Model HU80833 pressure washer was working, then no pressure. What is wrong? Unit is over two years old. Had been working properly earlier in day. While trying to finish job, it lost pressure and nothing would make it get back up to pressure. Also tried it again later, same result


... Honda Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

No pressure Pressure washer PC2525SP engin works great, no pressure from wand, water comes out just like a garden hose


You will have to try the following start up purge up onece with just water then start the powerwasher if that does'nt give u pressure ther is gaskets inside the pumping sometimes 4 to 8 of them these might be to wore down to hold pressure if u can lo ... Porter Cable PCH3200 Commercial Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

I have a tpw 2200 pressure washer that has lost high pressure. i have low pressure but not high pressure.rn The machine i have is a titan tpw 2200 if some body can tell me what is wrong please help. Thank john


Pour a large amount of liquid TSP into the fresh water inlet where the garden hose connects and let is sit for a couple of days.\015\012This is how I fixed my pressure problem ... Pressure Washers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0381 seconds