Having problems with your Karcher 1750 Psi Elec Pressure Washer ?

Motor running, water supply adequate but when

\015 Karcher 6.85 motor running, water supply adequate but when trigger pulled, pump not activated\015

Answers :

Clean whole water supply and outlet from all debris, clean inlet filter as well. connect water and pressurise washer, pull trigger and wait about 3sec for pump to activate, if pump do not activate adn you have pressure from nozzle as it will be from main, this determines pressure sensor (it is extremelly rare for pump itself) is damaged.

check if you have still warranty,this will qualify as warranty repair, if warranty is expired, pressure sensor need to be replaced.

if you find my advice useful, please do not hesitate to leave your remarks and vote for me, thanx!

Repair Help & Product Troubleshooting for Karcher 1750 Psi Elec Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor running, water supply adequate but when


Clean whole water supply and outlet from all debris, clean inlet filter as well. connect water and pressurise washer, pull trigger and wait about 3sec for pump to activate, if pump do not activate adn you have pressure from nozzle as it will be from ... Karcher 1750 Psi Elec Pressure Washer

Karcher K2.36 Pressure Washer I've just fired up my Karcher for the first time since last year and the motor started running fine, I then switched on the tap to allow the water through and the motor cut out. Now it won't restart, any ideas? I'm wondering whether the water supply should have been on before I switched the motor on but it's too late now! Help!


The water must be switched on, and seen to be running freely from the nozzle for a few seconds before switching on the power - suggest you check the fuse in the plug, and then try the above. ... Karcher K2.26 Electric Power Washer

The Motor is running but will not fill with water. I checked the water supply and drained the water out but it still will not fill with water.


I have a gibson energy saver disheasher and the water will not fill. motor is working ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

Whirlpool GU1100XLTQ1 dishwasher, 4 years old is leaking water during cycle. I cannot see exactly what is leaking by looking up through the acess panel in front...there are what appear to be plastic support ribs for the tub and water is leaking through several of them to the left of what appears to be the motor in the center...please help! I don't think I can run the washer and tilt it back at the same time as the water supply line only allows me to pull it out just enough to clear the counter t


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012wahgfadh ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

I've got a GE dishwasher, a GSD2800. It's giving a C4 code and it just won't drain the water. I turned the breaker to it on and off, shut off the water supply and tried to cycle it but no luck. I can hear the motor running. Any ideas out there??


If this is a new install where there was no dishwasher before. Or if your garbage disposal has been replaced. Then the plug in the garbage disposal inlet for the dishwasher drain may still be in place. You will have to disconnect the dishwasher drain ... General Electric GSD2400NWW Built-in Dishwasher

My five year old Viking dishwasher won't fill ...no water. Motor runs. No problem with water supply. the manual says check filter inlet valve. Where is that? thank you.


Hello, Yes your problem is going to be with the inlet valve. Remove the panel at the front bottom of the dish washer, turn the water and power off. You will see the inlet valve normally on the left side underneath your dishwasher (sometimes on right) ... Dishwashers

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

No water/pressure Motor runs and pumps for a few seconds then the revs increase and pressure and water fail as if there is no supply.There is a good supply and the input filter is clean


... Pressure Washers

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

My RMW 2.2G24 will not discharge water once the motor is running. When motor not running the water will flow through. It also appears the pump locks up every now and then becasue I cannot pull to start the motor. Bleed pressure and motor will start.


... Annovi Reverberi RMW2.5G25D

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

My Troybilt pressure Washer Model 020207. runs forabout 30 seconds then the motor stops. Acts like motor is locked up. Motor can't be pulled until water hose is disconnected. Took the water pump off and the 6.75 Briggs starts and runs like new. What could be the problem.


It sound like a digafame problem/or/carborater bowl has some water or needel valae is sticking cheack them if not the problem then you may have a crank shaft problem good luck see if there is oil in motor ... Briggs & Stratton Pressure Washers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Bosch SHU9925 motor is running but no water is coming in to wash


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers

Honda 3540CWHP cannot get water to spray with or without motor running. I have cleaned the filter and motor runs fine still no water? Help! Gary


... Pressure Washers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Won't start After two months of no use my dishwasher won't work. I can hear motor running but no water. We tried cleaning by filling with water (priming motor) but nothing happens. Now the dishwasher if full with water, motor makes noise but nothing is happening. Help!!


It sounds like you have a food blockage or some blockage between where the water fills up and where it goes into the pump you need to take out the water wand (the rotating thing with water coming out) only the bottom one. You need to unscrew the wate ... Hotpoint 24 in. HDA1000Z Built-in Dishwasher

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1427 seconds